Differential thermal analysis of the Al+20% (Fe-50%B) system

In the present study, aluminium and mechanically alloyed (36 h) Fe/B (50 wt%) are mixed. Al+20 (wt%) Fe/B mixture has been studied by differential thermal analysis to determine the aluminium quantity that is supposed to melt and afterwards does not solidify as it reacts with Fe/B powder. The different areas between endothermic reaction (melting peak) and exothermic reaction (solidification peak) allow in knowing the quantity of aluminium that reacts with Fe/B and the amount of intermetallic phases formed at high temperature. In order to follow the process, compacts were sintered at different temperatures (700, 800, 900, 1000 and 1200 °C), in N₂/10H₂/0.1CH₄ atmosphere. Microstructure was evaluated by image analysis and the results obtained by both techniques are compared.     

High modulus polyimide/polyimide molecular composite films that utilize acetylene unit as a crosslink site

Polyimide/polyimide molecular composite (MC) films comprised of a rigid polyimide derived from biphenyltetracarboxylic dianhydride (BPDA) and p-phenylenediamine (PDA) and a flexible polyimide derived from BPDA and bis (3,3'-diaminodiphenyl) acetylene (intA) and/or oxydianiline (ODA) were prepared by blending the polyamic acid solutions in 7 : 3 weight ratio, and then imidizing the blend films. Acetylene content in the flexible polyimide backbone was controlled by the ratio of intA and ODA. Cold-drawing of the blend polyamic acid films, followed by imidization, gives high modulus polyimide/polyimide MC films. The modulus of the MC films increased almost linearly with the draw ratio, reaching 25.5 GPa for the 40% drawn film. Acetylene groups in the flexible polyimide can be thermally cured to crosslink. The onset of exotherm appeared at 340°C on DSC, reaching maximum at 398°C. After the thermal crosslinking, the MC films maintained the high modulus, though elongation became small. Taking advantage of the crosslinkable acetylene units, two MC films were laminated and processed at 400°C for 20 min under 100 kg/cm² to give a good-quality laminate film. The interface of the two films was strongly bonded through the crosslinking of acetylene groups. Laminate films maintained the high modulus afforded by the cold-drawing. © 1994 John Wiley & Sons, Inc.     

分析信号处理方法的比较研究

研究了高效液相色谱－火焰原子吸收光谱联用系统分析信号处理方法，比较了各种处理方法的优缺点，用积分与适应平滑法综合处理色谱峰分析信号，不仅能有效地消除噪声，而且能使分析信号得到加强，以测定镍为例，经积分与适应平滑法综合处理后，检出限改善了２．７倍。     

Crystallization Temperature Limit of (Ba,Sr)TiO<Subscript>3</Subscript> Thin Films Prepared by a Non Oxocarbonate Phase Forming CSD Route

A new chemical solution deposition (CSD) route for the fabrication of Ba_0.7Sr_0.3TiO₃ (BST) thin films has been developed which completely prevents the formation of an intermediate oxo-carbonate phase. The latter has been reported previously by several authors to be responsible for increased crystallization temperatures. Barium and strontium diaminoethoxides were synthesized starting from pure barium and strontium metal and aminoethanol. These alkoxides were found to be readily soluble in a wide range of solvents and thus were excellent candidates for the CSD process. To prepare a stable precursor solution the aminoalkoxides were dissolved in 2-butoxyethanol and then used for the deposition of BST thin films. We conclude that the minimum crystallization temperature of 600C to be independent of the formation of the oxo-carbonate phase. DTA-TGA were performed on the precursors and their solutions to study their decomposition behaviour. All films annealed at different temperatures were physically characterized by XRD, IR, and SEM. The films prepared by this route at 650C were found to have high dielectric constant and the leakage currents were comparable to BST films prepared by normal carboxylate based routes at 750C.     

Thermal degradation of vinylidene chloride/vinyl chloride copolymers in the presence of N-substituted maleimides

As a consequence of their excellent barrier properties vinyl chloride/vinylidene chloride copolymers have long been prominent in the flexible packaging market. While these polymers possess a number of superior characteristics, they tend to undergo thermally- induced degradative dehydrochlorination at process temperatures. This degradation must be controlled to permit processing of the polymers. Three series of N-substituted maleimides (N-alkyl-, N-aralkyl, and N-aryl) have been synthesized, characterized spectroscopically, and evaluated as potential stabilizers for a standard vinyl chloride/vinylidene chloride (85 mass%) copolymer. As surface blends with the polymer, these compounds are ineffective as stabilizers. However, significant stabilization may be achieved by pretreatment of the polymer with N-substituted maleimides. The most effective stabilization of the polymer is afforded by N-aralkyl- or N-arylmaleimides, most notably, N-benzylmaleimide and N-p-methoxyphenylmaleimide.     

Extrapolated Smoothing Descent Algorithm for Constrained Nonconvex and Nonsmooth Composite Problems*

In this paper, the authors propose a novel smoothing descent type algorithm with extrapolation for solving a class of constrained nonsmooth and nonconvex problems,where the nonconvex term is possibly nonsmooth. Their algorithm adopts the proximal gradient algorithm with extrapolation and a safe-guarding policy to minimize the smoothed objective function for better practical and theoretical performance. Moreover, the algorithm uses a easily checking rule to update the smoothing parameter to ensure that any accumulation point of the generated sequence is an (affine-scaled) Clarke stationary point of the original nonsmooth and nonconvex problem. Their experimental results indicate the effectiveness of the proposed algorithm.     

Learning to align organizational design and data

The relationship between organizational learning and organizational design is explored. In particular, we examine the information processing aspects of organizational learning as they apply to a two-valued decision making task and the relation of such aspects to organizational structure. Our primary contribution is to extend Carley's (1992) model of this process. The original model assumes that all data input into the decision making processes are of equal importance or weight in determining the correct overall organizational decision. The extension described here allows for the more natural situation of non-uniform weights of evidence. Further extensions to the model are also discussed. Such organizational learning performance measures provide an interesting framework for analyzing the recent trend towards flatter organizational structures. This research suggests that flatter structures are not always better, but rather that data environment, ultimate performance goals, and relative need for speed in learning can be used to form a contingency model for choosing organizational structure.     

Thermal and mechanical-induced phase transformations during YAG and alumina–YAG syntheses

The preparation of pure Y₃Al₅O₁₂ (YAG) and 50 vol% Al₂O₃–YAG composite powders by a wet chemical route is presented. The role of the synthesis temperature during reverse-strike precipitation has been investigated, showing its relevant effect on the purity and homogeneity of YAG powder. The composite material was prepared by comparing two different synthesis routes. A composite powder was synthesized via reverse-strike temperature-controlled co-precipitation. In the latter case, a pure-alumina precursor was firstly reverse-strike precipitated and then doped with an yttrium salt solution. For both syntheses, the role of thermal and mechanical pre-treatments on the phase development was demonstrated.     

Modern Analysis

The important advances being made in modern analytical methods are indicative of the fundamental changes that are occuring in the theory and practice of “analytical chemistry”. “Information optimization” demands a new approach in teaching and research, and calls for the intergration of chemistry with other scientific and technical disciplines.     

Study of process parameters for starch,gluten, and glycerol mixtures

This work involved a study of the effect of processing variables (temperature, water content, rotor speed, and time) on the mechanical properties of starch:gluten:glycerol mixtures in the weight ratio of 40:40:20. The properties of the materials were affected by the processing variables. The torque decreased with water content, indicating that water facilitates the plasticization of mixtures, whereas the increase in temperature accelerated the evaporation of water, thus increasing the torque. Ultimate tensile strength was achieved at the lowest temperature (110°C) and the highest water content (20%), whereas maximum elongation was achieved for the material processed at the highest temperature, 150°C, and the fastest rotor speed, 70 rpm. Copyright © 2007 John Wiley & Sons, Ltd.