Experience Gained Using Second-Moment Closure Modeling for Transitional Flows Due to Boundary Layer Separation

This paper presents detailed information on the experience gained during the attempts to model a set of transitional flows due to boundary layer separation. These flows are developed on a flat plate with a semi-circular leading edge and they have been coded by the ERCOFTAC Special Interest Group on Transition, as T3L flows. Different freestream velocities and turbulence intensities configure these transitional flows and, by consequence, govern the transition mechanism, resulting in larger or smaller transitional regions. The modeling of the T3L flows has been performed by adopting a low-Reynolds number second-moment closure turbulence model. The results showed satisfactory agreement with the experimental measurements, although some difficulties regarding successful convergence have been faced. The final conclusion is that turbulence modeling can present quite accurate results for transitional flows without any additional use of ad-hoc modifications or additional equations based on various transition models and intermittency transport modeling.     

Carbon–epoxy composites based on fibers coated with nylon 6,6: hygrothermal ageing versus interlaminar shear strength

Carbon fibers were coated in situ with a thin film of polyhexamethylene adipamide by an interfacial polycondensation technique. The modified fibers were used for the preparation of epoxy-based unidirectional composites. Specimens of these materials were immersed in water until equilibrium conditions were attained. The weight gain at equilibrium was determined as a function of the immersion temperature, the fiber volume fraction and the polyamide content deposited on the fibers. Water penetration in specimens made with uncoated carbon fibers increases when the volume fraction decreases. Introduction of the polyamide interlayer initially increases the water absorption, but reduces it at higher immersion temperatures and/or higher polyamide contents. The treated specimens were subjected to the short beam test to determine the interlaminar shear strength (ILSS). The data show that the ILSS decreases with water penetration but increases when the immersion temperature increases from 40 to 70°C. The overall performance encountered is discussed in terms of the possible roles of the polyamide interphase while taking into account mechanisms concerned with matrix plasticization, interphase degradation and residual stress relaxation.     

各向异性材料中共线刚性线夹杂的纵向剪切问题

本文研究各向异性材料中共线刚性线夹杂，（有时称作“硬裂纹”或“反裂纹”问题）的纵向剪切问题。利用复变函数方法，提出了一般问题的公式和某些实际重要问题的封闭形式解，考察了刚性线端点附近的应力分布．从本文解答的特殊情形，可以直接导出各向同性材料相应问题的公式和结果，包括某些已有的结果￣［７］．     

Measurements and simulations of particle dispersion in a turbulent flow

A particle imaging technique has been used to collect droplet displacement statistics in a round turbulent jet of air. Droplets are injected on the jet axis, and a laser sheet and position-sensitive photomultiplier tube are used to track their radial displacement and time-of-flight. Dispersion statistics can be computed which are Lagrangian or Eulerian in nature. The experiments have been simulated numerically using a second-order closure scheme for the jet and a stochastic simulation for the particle trajectories. Results are presented for non-vaporizing droplets of sizes from 35 to 160 μm. The simulations have underscored the importance of initial conditions and early droplet displacement history on the droplet trajectory for droplets with large inertia relative to the turbulence. Estimates of initial conditions have been made and their effect on dispersion is quantified.     

一维应变压缩下TC4钛合金绝热剪切研究

 利用内径为57 mm的压缩气炮，在撞击速度为0.2~1.2 km/s（相应的靶中压力为3~15 GPa）范围内进行对称碰撞实验，以研究TC4（Ti-Al6-V4）钛合金在一维应变冲击压缩条件下的绝热剪切现象。对回收得到的受冲击样品，在扫描电镜（SEM）下进行细观金相分析。结果指出，一维应变冲击压缩条件下，TC4钛合金中绝热剪切带产生的对称碰撞速度阈值为500 m/s（相当于样品中的压力为5.87 GPa）；主剪切带与冲击方向约为45°角，带上有圆形和椭圆形两种孔洞且随碰撞速度的增大而增多和长大，这是典型的韧性损伤特征。随碰撞速度增大，产生与主剪切带成15°角的支剪切带。这些与理论预言相符。X射线能谱分析结果指出，剪切带内材料发生了(α+β)→β相的转变，是典型的相变带。剪切带的温度估算与实验提供的信息吻合。     

A generalized Adadorov theory for anisotropic thin-walled beams

This paper presents a generalized Adadorov theory for anisotropic thin—walled beams. The theory takes account of the shear strain of the middle surface, which exerts a significant influence on the anisotropic thin-walled beams. A new approach is established to solve the governing equations, which have the same form for both open and closed section beams. The numerical examples show that the effects of the shear strain cannot be neglected for this class of beams.This work was part of research project supported by the National Natural Science Foundation of China     

Mindlin板几何非线性分析的附加内部剪应变法

本文在几何非线性分析的Ｍｉｎｄｌｉｎ板元中引入单元附加内部剪应变，有效地解决了薄板情况下的剪切自锁问题．文中导出了相应的能量相容条件，给出了有限元非线性列式的全过程及有关簿板及中厚板大挠度问题的数值结果．     

Stress concentration around a circular hole in a transversely isotropic spherical shell

Analytical expressions for the stresses near a circular hole in a transversely isotropic shallow spherical shell under uniform pressure are derived. The form of the solution depends on the range of change in the compliance to transverse shear. The influence of the relative radius of the hole and the compliance to transverse shear on the stress concentration is analyzed.__________Translated from Prikladnaya Mekhanika, Vol. 40, No. 12, pp. 99–106, December 2004.     

冲击载荷下剪切断裂研究

利用Hopkinson压杆技术对单边平行双裂纹试样倒向加载，在较大的加载率范围，对Ti6Al4V钛合金和40CrNiMoA两种材料的动态剪切断裂行为进行了研究．实验结果表明：存在两类韧性剪切断裂模式，即常规的韧性剪切型断裂和绝热剪切断裂．常规剪切型断裂模式的断裂韧性KⅡd随加载率的提高而增大，而绝热剪切型的断裂韧性KⅡd则随加载率的提高而减小，并且，当加载率增大至某一临界值时，常规的韧性剪切断裂模式将转变为绝热剪切断裂破坏模式．     

Thickness decrease of a grafted polyelectrolyte membrane exposed to shear flow

The effect of the shear flow on the thickness change of a polyelectrolyte membrane grafted onto a glass substrate was directly investigated with a flow cell combined with a confocal laser scanning microscope. The membrane thickness decreased proportionally to an increase in the shear stress of the flow when the shear rate exceeded a critical value of 1 s^?1. The higher the ionic strength was of the fluid, the greater the thinning effect was. The correlation between the critical shear rate and the relaxation of the polymer in the gel membrane was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2808–2815, 2003