HYDROPHOBICITY OF CONTAMINATED SILICONE RUBBER SURFACES

Silicone rubber (SIR) shows superior performance when used outdoors, but its surface can be transformed frominherently hydrophobic to hydrophilic by the adsorption of contaminants. Al(OH)_3, Al_2O_3, quartz powder and active carbonwere selected as authentic contaminants. Hydrophobicity of the surface was determined using contact angle measurement.The results indicate that the adsorbability of the contaminants can strongly affect the hydrophobicity of contaminated SIRsurface. The increasing rate of contact angle of specimens contaminated by Al(OH)_3 was much faster than that by Al_2O_3 andquartz due to the adsorption of migrated low molecular weight (LMW) polydimethylsiloxanes. Specimens contaminated byactive carbon could achieve sunde hydrophobicity within 15 min because active carbon has high adsorbability. Surfaces ofcontaminated ultrapure SIR, polytetrafluoroethylene (PTFE) and glass remain hydrophilic because they contain no mobileLMW components. The addition of oligomeric polydimethylsiloxanes has little effect on the hydrophobicity of contaminantscovered on SIR surface.     

An investigation of dynamic mechanical, thermal, and electrical properties of housing materials for outdoor polymeric insulators

The present paper reports the results about a study of mechanical, thermal, dynamic mechanical and electrical properties of housing (weather shed) materials for outdoor polymeric insulators. Silicone rubber, ethylene-propylene-diene monomer (EPDM) and alloys of silicon-EPDM are known polymers for use as housing in high voltage insulators. The result of dynamical mechanical measurement shows that the storage modulus of blends enhances with increase EPDM in formulation. It can be seen from the result of TGA measurement that initial thermal degradation of silicone rubber improves by the effect of EPDM in blends. The blends of silicone-EPDM show good breakdown voltage strength compared to silicone rubber. Surface and volume resistance of silicone rubber improve by EPDM content. The mechanical properties of EPDM such as strength, modulus and elongation at break improve by silicone.     

Photocrosslinking of functionalized rubber. II. Photoinitiated cationic polymerization of epoxidized liquid natural rubber

Low molecular weight epoxidized natural rubber has been crosslinked within seconds by UV irradiation in the presence of a triarylsulfonium salt. The photoinitiated cationic ring-opening polymerization was studied quantitatively by infrared spectroscopy and shown to proceed with surprisingly long kinetic chains in such solid medium. The high conversion (60%) needed for complete insolubilization, together with the presence of tetrahydrofuran structures, argue in favor of an intramolecular polymerization process involving neighboring epoxy groups. The photoinitiator concentration has a strong influence on the rate and extent of the reaction, as well as on the depth of cure profile. Because of an efficient dark process, close to 100% conversion was reached upon storage of the irradiated elastomer at ambient, with a concomitant increase of the gel fraction and the polymer hardness. The grafting of pendent acrylate groups onto the polymer chain leads to a three-fold decrease of the initial rate of polymerization of the epoxide. The photocuring of natural rubber bearing both epoxy and acrylate groups generates a dual polymer network which combines the properties of the two moieties. © 1995 John Wiley & Sons, Inc.     

Chemical preparation of conductive elastomeric blends: Polypyrrole/EPDM. I. Oxidant particle-size effect

This work describes the preparation of polypyrrole and EPDM rubber blends, PPy/EPDM, by the sorption of pyrrole (vapor phase) in an EPDM matrix containing CuCl₂. We investigated the effect of the oxidant particle-size on the sorption and polymerization equilibrium, electrical conductivity, and mechanical properties of the blends. Independently of the CuCl₂ concentration and polymerization time, the polypyrrole weight fraction in the blend, X_ppy, increases when the oxidant particle-size in changed from 150–250 μm to smaller than 106 μm. For blends containing 50 phr of CuCl₂, obtained following 72 h of exposure to pyrrole, an increase in the Young's Modulus (from 2.2 ± 0.2 to 3.9 ± 0.6 MPa) and an increase in the electrical conductivity (from 10^?9 to 10^?7 S cm^?1) was observed when the oxidant particle-size was decreased. Infrared spectroscopy, thermogravimetric analysis, scanning differential calorimetry, and scanning electron microscopy were used in sample characterization. © 1994 John Wiley & Sons, Inc.     

Synthesis of N,N-diethyldithiocarbamate functionalized 1,4-polyisoprene, from natural rubber and synthetic 1,4-polyisoprene

N,N-Diethyldithiocarbamate functionnalized 1,4-polyisoprenes were prepared from 1,4-polyisoprenes (natural or synthetic). The syntheses were performed by nucleophilic addition of N,N-diethyldithiocarbamate salts upon oxirane rings of epoxidized units according to a SN2 mechanism with ring opening. Studies on model molecules of epoxidized 1,4-polyisoprene units (1,2-epoxy-1-methylcyclohexane and 4,5-epoxy-4-methyloctane) were previously achieved to develop the procedure. The best yields were obtained at low temperature in polar medium, and more especially in water with sodium N,N-diethyldithiocarbamate (DEDT-Na) as reagent. A diastereospecific addition was noted when reaction was performed in water with DEDT-Na. Afterwards, the developed procedure was successfully generalized to epoxidized synthetic polyisoprenes and epoxidized natural rubber (in THF, then in latex medium). Excellent results were obtained in latex medium with epoxidized natural rubber (ENR) latices. As with the models, a diastereospecific addition of sodium N,N-diethyldithiocarbamate trihydrate onto epoxidized 1,4-polyisoprene units of ENR was observed at the condition to bring the latex medium to pH 8 before introduction of DEDT-Na. Influence of temperature, drc, and DEDT-Na concentration were successively examined to determine the best conditions of the addition on ENR latices.     

A study for quality evaluation of Taxilli Herba from different hosts based on fingerprint-activity relationship modeling and multivariate statistical analysis

In this study, a fingerprint-activity relationship modeling between chemical fingerprints and antirheumatic activity was established, and multivariate statistical analysis was used to evaluate the quality of Taxilli Herba (TH) from different hosts. Characteristic fingerprints of 20 batches of TH samples were generated by high-performance liquid chromatography coupled with triple quadrupole-time of flight tandem mass spectrometry (HPLC-Triple TOF-MS/MS), and the similarity analysis was calculated based on thirteen common characteristic peaks by hierarchical clustering analysis (HCA). Subsequently, nine efficacy markers were discovered by combining fingerprints and antirheumatic activity through grey correlation analysis (GCA) and bivariate correlation analysis (BCA). Meanwhile, the content of 5 constituents in 9 markers was determined by high-performance liquid chromatography coupled with triple quadrupole-linear ion trap tandem mass spectrometry (HPLC-QTRAP-MS/MS). The comprehensive quality of TH was assessed using multivariate statistical analysis, including principal components analysis (PCA) and technique for order preference by similarity to ideal solution (TOPSIS). The results showed that a high dose of TH extract could markedly ameliorate arthritis damage compared to other doses, with flavonoids playing an important role in the antirheumatic activity. The comprehensive quality of samples from Morus alba L. (SS) was superior to those from Liquidambar formosana Hance (FXS). The present study will demonstrate the markers associated with efficacy, and provide an applicable strategy for more comprehensive quality control and evaluation of TH.     

Studies on accelerated sulphur vulcanization of natural rubber using 1-phenyl-2, 4-dithiobiuret/tertiary butyl benzothiazole sulphenamide

The use of binary accelerators has gained tremendous importance since it increases the production rate of the article made of that elastomer. The authors have analyzed the performance of a novel binary accelerator system in the sulphur vulcanization of natural rubber (NR). The vulcanizates resulting from the binary accelerated process obtained good mechanical properties, ageing and swelling resistance. Network characterization of the mixes was done using swelling measurements, stress-strain analysis etc. The chain entanglement density was measured using dynamic mechanical analysis. However the performance is found to be dependent on the relative proportion of mono, di and polysulphidic linkages in the material. The result of the study points out that the proposed system can be active in NR regardless of the vulcanization recipe and temperature. The performance of the new binary system in filled vulcanizates is also studied. Based on the processing, mechanical and chemical characterization an optimum concentration is suggested for the new system.     

Mechanical properties of fiber reinforced styrene-butadiene rubbers using surface-modified UHMWPE fibers under EB irradiation

Aiming to develop a high performance fiber reinforced rubber of SBR, a special technique using electron beam (EB) irradiation-induced graft-polymerization was applied to ultra-high molecular-weight polyethylene (UHMWPE) fibers. Although UHMWPE is chemically inert, N-vinyl formamide (NVF) could be graft-polymerized onto the UHMWPE fiber surface with this special technique. A maximum grafting percentage of 23.6% was achieved. The composite of SBR and grafted UHMWPE fibers with maximum grafting indicated a linear increase in the initial modulus and strength with the fiber content. At the fiber content of 10%, the initial modulus was improved about five times with respect to that of the pure SBR, while the strength was done about twice. At this moment, only a small reduction could be observed in the strain compared with that of pure SBR. The fiber reinforced rubber with a good performance was obtained in the system of SBR and grafted UHMWPE fibers.     

环氧化橡胶及其合金的研究与应用

综述了国内外环氧化橡胶及其合金的研究现状和应用趋势,重点介绍了环氧化天然橡胶、环氧化聚丁二烯、环氧化苯乙烯-丁二烯-苯乙烯三嵌段共聚物及其合金的优点,以及影响其物理机械性能的因素和环氧化橡胶的发展方向。     

Quarter wave plates for submillimeter wavelengths

A review is given of different types of quarter wave plates as presently used in the optical and microwave spectral range, with a view to their application in the sub-mm wave-length range. Two types of quarter wave plates have been constructed and results of measurements at 640m are given.