水煤浆喷嘴热冲蚀磨损机理研究

采用1Crl8Ni9Ti不锈钢、YG8硬质合金和Al2O3／(W，Ti)C陶瓷3种材料制备了水煤浆喷嘴，考察了其在水煤浆雾化和燃烧过程中的热冲蚀磨损机理．结果表明：喷嘴材料的硬度对水煤浆喷嘴的热冲蚀磨损行为具有重要影响；在相同条件下，高硬度的Al2O3／(W，Ti)C陶瓷喷嘴的冲蚀率最低，YG8硬质合金次之，硬度较低的1Crl8Ni9Ti不锈钢喷嘴的冲蚀率最高；在热冲蚀磨损工况下，1Crl8Ni9Ti不锈钢水煤浆喷嘴主要呈现微切削特征，YG8硬质合金水煤浆喷嘴主要呈现晶粒剥落特征，而Al2O3／(W，Ti)C陶瓷水煤浆喷嘴主要呈现研磨损伤和热崩特征．     

耐磨环氧胶粘涂层冲蚀磨损特性的研究

本文对气固冲蚀和浆体冲蚀条件下耐磨环氧胶粘涂层的磨损特性进行了研究。结果表明,这种涂层的冲蚀磨损是由粘结剂的磨损和抗磨填料的磨损所组成;填料粒度和磨料粒度都对涂层的气固冲蚀磨损有影响,但在给定的试验条件下,填料粒度对涂层的浆体冲蚀磨损影响甚微。文章指出,耐磨环氧胶粘涂层在气固冲蚀和浆体冲蚀下的磨损机理相似,但磨损规律却有所不同;耐磨环氧胶粘涂层尤其适用于浆体冲蚀的场合,可以明显地提高机械过流部件的使用寿命。     

几种高分子材料的磨粒侵蚀机理

本文采用自行设计制造的磨粒侵蚀试验台对聚氨酯、丁苯橡胶、尼龙6和聚四氟乙烯4种高分子材料的磨粒侵蚀行为进行了试验研究,并且通过扫描电镜对试样磨损表面进行了观察分析,分别提出了这4种高分子材料磨粒侵蚀的物理模型和物理过程,阐明了它们的磨粒侵蚀机理:具有一定动能的固体颗粒对材料表层产生微切削;微观裂纹的萌生与扩展导致材料表层微观剥落;材料的力化学分解和热分解;材料表层局部塑性变形发展成塑性断裂而从表面脱落。     

冲蚀与气蚀复合磨损试验研究

通过改造MCF-30型冲蚀腐蚀试验机,建立了水、沙、气三相流冲蚀磨损试验装置;试验研究了水、沙混合流场中试样的磨损特征,通过扫描电子显微镜观测了三相流冲蚀磨损表面,并借助计算机模拟分析水、沙混合条件下产生气蚀破坏的条件.结果表明:合理的设计可以实现冲蚀与气蚀的复合磨损模拟试验;形成三相流共同作用下的冲蚀与气蚀复合磨损重要条件为介质中含有较多气体,并且在试样中有气泡溃灭.三相流磨损模拟试验与仿真为进一步开展三相流气蚀与冲蚀磨损研究奠定了基础.     

Rime- and glaze-ice accretion due to freezing rain falling vertically on a horizontal thermally insulated overhead line conductor

A theory of atmospheric icing due to freezing rain on an overhead line conductor (OHLC) is developed. The rain falls vertically on a horizontal OHLC that is thermally insulated. It is assumed that the collection efficiency of the accretion surface is unity and that this surface is in thermodynamic equilibrium with the environment.

For air temperature T_A 0°C and raindrop temperature T_D 0°C, the freezing rain accretes as rime ice, provided that the temperature of the ice surface T_l < 0°C. The evolution equation governing the mass transfer at the accretion surface is solved analytically, yielding the shape of the rime-ice surface. Equations governing the thermal state of the rime-ice deposit are also given. These determine the onset of wet growth or glaze accretion at the upper stagnation line during suitable environmental conditions.

For environmental conditions producing an ice surface at temperature T_l = 0°gC, the freezing accretes as glaze. Equations governing the heat and mass transfer at the surface determine the shape of the glaze surface and the downward viscous motion of the unfrozen water. For T_D < 0°C, glaze evolution equations are developed for T_A 0°C and T_A 0°C. Analytical solutions of these equations are obtained. In particular, when T_D < −T_A < 0°C, the evolution equation predicts a novel limiting growth that is triangular in shape. Further study of the mass and heat transfer conditions, in the neighborhood of this final stage of glaze accretion, shows that it is maintained in thermodynamic equilibrium with its warm air environment.     

冲击速度和磨粒粒度对FeCrAl/WC复合涂层冲蚀性能的影响

采用粉芯丝材作为原料,利用高速电弧喷涂技术制备了具有良好抗高温冲蚀磨损性能的FeCrAl/WC复合涂层;考察了650℃下冲击速度和磨粒粒度对复合涂层高温冲蚀磨损性能的影响.结果表明,复合涂层和20G锅炉钢的耐高温冲蚀磨损能力随着磨粒粒度的增加而有所提高;30°攻角下冲蚀率随磨粒粒度的变化速率比90°攻角下的小;同20G锅炉钢相比,复合涂层对速更加敏感,速度越低,FeCrAl/WC复合涂层的抗冲蚀磨损性能越好.     

模拟酸雨条件下浙江省金华市城市灰尘重金属的解析状况探究

通过网格采样法,采集了金华市一环线以内地区的20个城市灰尘样品,然后利用原子吸收分光光度计测定了城市灰尘重金属Zn、Cu、Cr和Pb在不同pH的模拟酸雨溶液浸提下的析出值,并采用地积累指数法对各重金属有效性的状况做出了评价。结果表明,研究区域内,城市灰尘重金属Zn、Vu、Cr和Pb在酸雨背景下的析出值分别处于清洁水平、轻污染水平、中等污染水平和偏中等污染水平,该区城市灰尘有效Cr和有效Pb的污染程度较高,值得关注与采取措施进行预防与整治。     

Solid‐particle erosion in the tube end of the tube sheet of a shell‐and‐tube heat exchanger

Erosion is one of the major problems in many industrial processes, and in particular, in heat exchangers. The effects of flow velocity and sand particle size on the rate of erosion in a typical shell‐and‐tube heat exchanger were investigated numerically using the Lagrangian particle‐tracking method. Erosion and penetration rates were obtained for sand particles of diameters ranging from 10 to 500 µm and for inlet flow velocities ranging from 0.197 to 2.95 m/s. A flow visualization experiment was conducted with the objective of verifying the accuracy of the continuous phase calculation procedure. Comparison with available experimental data of penetration rates was also conducted. These comparisons resulted in a good agreement. The results show that the location and number of eroded tubes depend mainly on the particle size and velocity magnitude at the header inlet. The rate of erosion depends exponentially on the velocity. The particle size shows negligible effect on the erosion rate at high velocity values and the large‐size particles show less erosion rates compared to the small‐size particles at low values of inlet flow velocities. The results indicated that the erosion and penetration rates are insignificant at the lower end of the velocity range. However, these rates were found to increase continuously with the increase of the inlet flow velocity for all particle sizes. The particle size creating the highest erosion rate was found to depend on the flow velocity range. Copyright © 2005 John Wiley & Sons, Ltd.     

The effects of rain clutter on millimeter radar performance

The effects of rain clutter on millimeter radar performance are investigated at 35, 94 and 140GHz frequencies, including rain attenuation, radar reflectivity, maximum radar range and equivalent target cross section.     

有雨概率与分维数关系的初步研究

对武汉地区１９８２～１９９４年有雨分维数与有雨概率之间的关系进行了初步的分析和研究，并给出了研究结果．为今后修改降雨衰减预报模型作准备．