用楔形柱面光纤微透镜耦合的1.3μm SOA组件

运用激光模式耦合理论分析了半导体光放大器(SOA)与单模通信光纤的连接损耗,并设计制作了楔形柱面光纤微透镜用来实现两者的模斑匹配,有效地降低了器件的光耦合损耗.本文介绍了楔形柱面光纤微透镜耦合的1.3 μm半导体光放大器(SOA)组件及其制作方法.该组件的最大增益不小于14 dB,其偏振灵敏度小于1 dB,增益波动不大于0.5 dB.     

两段级联掺铒光纤放大器的优化研究

基于Giles模型,研究了980 nm和1480 nm泵浦的两段级联掺铒光纤放大器(EDFA)的设计,得出了掺铒光纤(EDF)的最佳长度和光隔离器的最佳位置随泵浦功率和信号功率的变化关系.比较980 nm和1480 nm泵浦的两段级联EDFA,可以发现,前者的最佳EDF长度短,而光隔离器最佳位置距EDFA输入端远.     

Nd~(3+):YAG激光的光纤传输

首先叙述了光纤传输Nd~(3+): YAG激光的优点,接着分析了不同光纤和其传输Nd~(3+): YAG激光的特点。然后通过对光纤传输系统各部分的分析与设计,结合实际,设计了光纤耦合机构。最后,对来自于工件反射光问题提出了解决方案。     

Self-Interactions of Strands and Sheets

Physical strands or sheets that can be modelled as curves or surfaces embedded in three dimensions are ubiquitous in nature, and are of fundamental importance in mathematics, physics, biology, and engineering. Often the physical interpretation dictates that self-avoidance should be enforced in the continuum model, i.e., finite energy configurations should not self-intersect. Current continuum models with self-avoidance frequently employ pairwise repulsive potentials, which are of necessity singular. Moreover the potentials do not have an intrinsic length scale appropriate for modelling the finite thickness of the physical systems. Here we develop a framework for modelling self-avoiding strands and sheets which avoids singularities, and which provides a way to introduce a thickness length scale. In our approach pairwise interaction potentials are replaced by many-body potentials involving three or more points, and the radii of certain associated circles or spheres. Self-interaction energies based on these many-body potentials can be used to describe the statistical mechanics of self-interacting strands and sheets of finite thickness.     

Mechanical Properties of Blends of Low-Density Polyethylene with Chlorinated Polyethylene

The results of experimental investigation into the mechanical properties of blends of low-density polyethylene (LDPE) with chlorinated polyethylene (CPE) in tension are presented. The specimens of pure LDPE, CPE, and nine types of LDPE/CPE blends, with different content of components at 10 wt.% intervals, were examined. Data on the influence of blend composition on the tensile stress-strain diagram, elastic modulus, yield stress, breaking stress, and ultimate elongation are obtained. The results of investigations of creep are also reported. It is found that the creep compliance (the total current compliance minus the elastic compliance) obeys the power law of creep.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 391–404, May–June, 2005.     

Optical bistability in an all-optical fiber nonlinear fabry-perot resonator with linear absorption

An all-optical fiber nonlinear Fabry-Perot resonator is proposed. The steady-state model for describing this resonator is developed. The transmission and refection bistabilities are shown numerically. Our results show that the bistability in this system is similar to that in a normal nonlinear Fabry-Perot etalon, except that the characteristics of the bistability can be changed not only by the cavity length but also by the phase shifts of the fiber loop mirrors.     

The Modeling of Velocity Enhancement in Polymer Flooding

In single-phase polymer flooding experiments it has repeatedly been observed that the average velocity of the polymer molecules is higher than the average velocity of the water molecules. This effect is incorporated in many conventional Enhanced Oil Recovery (EOR) simulators by the introduction of a constant velocity enhancement factor. In this paper we show that, in absence of dispersion, a constant enhancement factor in the mathematical model for two-phase polymer flow (Buckley--Leverett displacement) leads to ill-posedness of the model equations. We propose a saturation dependent enhancement factor, derived from a model based on percolation concepts, for which this problem does not occur.     

A highly selective solid phase extraction sorbent for pre-concentration of sameridine made by molecular imprinting

Summary A novel approach to solid phase extraction, based on the use of a highly selective molecularly imprinted polymer, is presented. The versatility of this type of sorbent for solid phase extraction was demonstrated in a model batch-wise pre-concentration of sameridine prior to gas chromatography. Problems associated with leakage of remaining imprint molecules during the desorption phase could be eliminated by the use of a close structural analogue of sameridine as the imprint species. It was found that a major benefit of the imprinted polymer was its specificity, which lead to distinctly cleaner chromatographic traces and ability to improve sensitivity by extracting sameridine from larger sample volumes.     

折射率温敏式光纤温度传感器的理论模型

提出了折射率温敏式光纤温度传感器的理论模型，包括子午光线和偏射光线的影响，讨论了多模光纤的弯曲损耗，理论的分析和结果与实验相当一致。     

Structural characterization of polypyrrole in the solid state by high resolution 15N NMR spectroscopy [II]

The solid-state ¹⁵N CP/MAS NMR spectra and ¹⁵N spin-lattice relaxation times (T₁) of doped and dedoped ¹⁵N-labeled polypyrroles prepared by electrochemical polymerization, have been measured by means of high-resolution solid-state ¹⁵N NMR. The ¹⁵N signal of polypyrrole consists of four peaks decomposed by line shape analysis. The four peaks obtained have been assigned to the various structures of polypyrrole. Further, the half-width of the ¹⁵N NMR spectra of polypyrroles is discussed as related to the electrical conductivity. © 1995 John Wiley & Sons, Inc.