X-ray damage characterization in BaLiF3,KMgF3 and LiCaAlF6 complex fluorides

Two-inch sized KMgF₃,BaLiF₃ and LiCaAlF₆ (LiCAF) single crystals were grown by the Czochralski method under a CF₄ atmosphere. X-ray irradiation was used to carry out a comparative study of induced optical absorption phenomena and colour centre creation in the ultra-violet and visible spectral regions. The integral of the induced absorption spectra is significantly lower in LiCAF with respect to the other studied materials. It is found that the amplitude of the F-absorption band is suppressed more than a factor of 3 by Mg-doping. For Mg-doped crystals, the optimum doping concentration is about 0.2 mol% of Mg²⁺.     

Dispersion Characteristics of Waveguide Arrays in Optical Spectrum Analyzers

Formulas for calculating the spectral characteristics of waveguide arrays, which are incorporated into waveguide spectrum analyzers based on planar waveguides, channel waveguides, and fiber optical waveguides, are derived taking into account the contribution of both the waveguide dispersion and the material dispersion to the dispersion factor. These formulas are used to study the dependence of the dispersion factor on the waveguide-system parameters for specific models of waveguide arrays. It is shown that consideration of contributions of the waveguide dispersion and material dispersion can affect profoundly the spectral characteristics of waveguide arrays.     

Measurement uncertainty of selenium determination in the reference material Seronorm Trace Elements Serum by hydride generation atomic fluorescence spectrometry

 An analytical result is not considered to be complete without a statement of the measurement uncertainty associated with it. Evaluation of measurement uncertainty is therefore an essential part of every determination. In the present study the measurement uncertainty of the result of determination of selenium in the reference material Seronorm Trace Elements Serum was studied. The combination of a digestion procedure using sulfuric acid, V₂O₅ in H₂SO₄ and hydrogen peroxide and the continuous flow approach of hydride generation atomic fluorescence spectrometry (HG-AFS) detection was used for selenium determination. The total uncertainty budget was calculated with the help of the GUM Workbench program, in which computations follow the rules of the ’ISO guide to the expression of uncertainty in measurement’. The major sources of uncertainty were found to be due to the recovery of the procedure, measurement of peak heights and the purity of Na₂SeO₃. A selenium mass fraction of 77.1±4.8 ng/g (with a coverage factor of 2.1, 95% probability) was determined, which is comparable with the recommended value of 80 ng/g. Received: 13 September 2002 Accepted: 23 December 2002 Acknowledgements We would like to thank Tinkara Buˇcar, B.Sc. for useful discussions and the IAEA Vienna, for financial support of the project 11553/RO. Presented at CERMM-3, Central European Reference Materials and Measurements Conference: The function of reference materials in the measurement process, May 30–June 1, 2002, Rogaška Slatina, Slovenia Correspondence to V. Stibilj     

散射体系A+BC的平-振能量传递

用Alhassid与Levine所提出的动力学李代数的方法(简称A-L理论),研究了含有二级非简谐的共线散射体系A+BC的平-振能量传递问题,计算了散射过程含有主要动力学参量的跃迁矩阵和跃迁几率的解析表示式.     

The Ring of Invariants of Three (3 × 3)-Matrices over a Field of Prime Characteristic

We find a minimal system of generators and a homogeneous system of parameters for the algebra of invariants of three matrices of third order over a field of an arbitrary characteristic.     

On the dynamic electromechanical loading of dielectric elastomer membranes

Dielectric elastomer actuators (DEAs) have received considerable attention recently due to large voltage-induced strains, which can be over 100%. Previously, a large deformation quasi-static model that describes the out-of-plane deformations of clamped diaphragms was derived. The numerical model results compare well with quasi-static experimental results for the same configuration. With relevance to dynamic applications, the time-varying response of initially planar dielectric elastomer membranes configured for out-of-plane deformations has not been reported until now. In this paper, an experimental investigation and analysis of the dynamic response of a dielectric elastomer membrane is reported. The experiments were conducted with prestretched DEAs fabricated from 0.5 mm thick polyacrylate films and carbon grease electrodes. The experiments covered the electromechanical spectrum by investigating membrane response due to (i) a time-varying voltage input and (ii) a time-varying pressure input, resulting in a combined electromechanical loading state in both cases. For the time-varying voltage experiments, the membrane had a prestretch of three and was passively inflated to various predetermined states, and then actuated. The pole strains incurred during the inflation were as high as 25.6%, corresponding to slightly less than a hemispherical state. On actuation, the membrane would inflate further, causing a maximum additional strain of 9.5%. For the time-varying pressure experiments, the prestretched membrane was inflated and deflated mechanically while a constant voltage was applied. The membrane was cycled between various predetermined inflation states, the largest of which was nearly hemispherical, which with an applied constant voltage of 3 kV corresponded to a maximum polar strain of 28%. The results from these experiments reveal that the response of the membrane is a departure from the classical dynamic response of continuum membrane structures. The dynamic response of the membrane is that of a damped system with specific deformation shapes reminiscent of the classical membrane mode shapes but without same-phase oscillation, that is to say all parts of the system do not pass through the equilibrium configuration at the same time. Of particular interest is the ability to excite these deformations through a varying electrical load at constant mechanical pressure.     

Activation energies for metastable to stable phase transition of 4,4'-di-n-heptyl- oxyazoxybenzene

Complexes of adenine, AdH, with cobalt, nickel and copper chlorides were prepared and their thermodynamic functions were determined. The complexing processes are endothermic in nature. The thermal behaviour of complexes was followed up by using TG and DTA analyses. The stoichiometry of thermal decomposition of the investigated complexes was suggested. This revised version was published online in August 2006 with corrections to the Cover Date.     

Synthesis and optical properties of tetraphenylmethane-based tetrahedral fluorescent compounds and their water-soluble PEG-linked polymers

The synthesis and optical properties of tetrahedral fluorescent compounds comprising of tetraphenylmethane as the core and oligothiophenes as the chromophoric arms, and their water-soluble poly(ethylene glycol)-linked polymers are reported.     

Sterically stabilized emulsion polymerization of styrene: Pseudo‐semicontinuous approach

The sterically stabilized emulsion polymerization of styrene initiated by a water‐soluble initiator at different temperatures has been investigated. The rate of polymerization (R_p) versus conversion curve shows the two non‐stationary‐rate intervals typical for the polymerization proceeding under non‐stationary‐state conditions. The shape of the R_p versus conversion curve results from two opposite effects—the increased number of particles and the decreased monomer concentration at reaction loci as the polymerization advances. At elevated temperatures the monomer emulsion equilibrates to a two‐phase or three‐phase system. The upper phase is transparent (monomer), and the lower one is blue colored, typical for microemulsion. After stirring such a multiphase system and initiation of polymerization, the initial coarse polymer emulsion was formed. The average size of monomer/polymer particles strongly decreased up to about 40% conversion and then leveled off. The initial large particles are assumed to be highly monomer‐swollen particles formed by the heteroagglomeration of unstable polymer particles and monomer droplets. The size of the “highly monomer” swollen particles continuously decreases with conversion, and they merge with the growing particles at about 40–50% conversion. The monomer droplets and/or large highly monomer‐swollen polymer particles also serve as a reservoir of monomer and emulsifier. The continuous release of nonionic (hydrophobic) emulsifier from the monomer phase increases the colloidal stability of primary particles and the number of polymer particles, that is, the particle nucleation is shifted to the higher conversion region. Variations of the square and cube of the mean droplet radius with aging time indicate that neither the coalescence nor the Ostwald ripening is the main driving force for the droplet instability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 804–820, 2003     

Sensitivity of trust-region algorithms to their parameters

In this paper, we examine the sensitivity of trust-region algorithms on the parameters related to the step acceptance and update of the trust region. We show, in the context of unconstrained programming, that the numerical efficiency of these algorithms can easily be improved by choosing appropriate parameters. Recommended ranges of values for these parameters are exhibited on the basis of extensive numerical tests. MSC classification: 65K05, 90C26, 90C30