Synthesis and refractive‐index control of fluoropolymers by the polyaddition of bis(epoxide)s and triazine di(aryl ether)s

The polyaddition of fluorine‐containing bis(epoxide)s and fluorine‐containing triazine di(aryl ether)s were examined to give the corresponding fluorine‐containing poly(cyanurate)s. It was observed that the synthesized fluoropolymers had good thermal stabilities and good film‐forming properties. The glass transition temperatures (T_g's) and refractive‐indices (n_D's) of synthesized polymers were determined by differential scanning calorimetry and ellipsometry, respectively, and it was found that the values of T_g's and n_D's were supported by their fluorine containing ratios and skeletons. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4421–4429, 2007     

Evidences of phase separation in moisture‐cured poly(urethane urea)s by means of temperature modulated differential scanning calorimetry

The degree of phase separation in several moisture‐cured poly(urethane urea)s (PUUs) was studied by FTIR spectroscopy, wide angle X‐ray diffraction (WAXD), and temperature‐modulated differential scanning calorimetry (TMDSC). This latter technique was shown to be particularly useful in analysing the degree of phase separation in PUU polymers. Both phase mixing and phase segregation coexisted in the PUUs and the degree of phase separation increased as the urea hard segment (HS) content in the PUU increased. The maximum solubility of urea HSs into the polyol soft segments (SSs) was achieved for 50 wt % urea HS content in diol‐based PUUs, whereas for triol‐based PUUs the highest solubility between HS and SS was reached for lower urea HS amount. Finally, the higher the urea HS content the higher the extent of phase separation in the PUU. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 3034–3045, 2007     

碳纳米管阵列、捆束的三步升温工艺制备及其形貌与结构

使用结构简单的单温炉设备，通过三步升温热解二茂铁、三聚氰氨混合物方法，在二氧化硅、多晶陶瓷基底上分别合成了碳纳米管阵列、碳纳米管捆束.使用扫描电子显微镜、透射电子显微镜、电子能量损失谱和x射线光电子能谱对合成样品进行了结构和成分分析.结果显示：两种基底上合成的纳米管均为多壁纯碳管；生长于光滑二氧化硅表面的碳纳米管具有高度取向性和一致的外径，长度为10—40μm.碳纳米管采取催化剂顶端生长模式并展示出类杯状形貌；生长于粗糙多晶陶瓷表面的碳纳米管捆束随机取向，碳纳米管直径为15—80nm，长度在几百微米，展示 关键词： 碳纳米管 热解法 三步升温工艺     

BEPCII直线加速器相控系统设计研究

为了补偿由于各种因素引起的微波相位漂移,BEPCII直线加速器需要建立微波相位反馈控制系统.能量最大法将用来确定每台功率源的最佳相位.沿直线加速器速调管长廊铺设相位稳定同轴线提供相位参考.现在已经完成了关键部件,如PAD单元、IfA 单元的开发.搭建了相控最小系统对系统进行了验证.     

Temperature coefficient of NH chemical shifts of thioamides and amides in relation to structure

NH chemical shift temperature coefficients have been measured in a large series of N-substituted-3-piperidinethiopropionamides in which the NN distances are short but of varied length, as well as in a couple of the corresponding amides and in some simpler amides and thioamides. Geometries are calculated by means of ab initio DFT methods. The N-substituted-3-piperidinethiopropionamides show in most cases strong intramolecular N–HN hydrogen bonds according to IR spectra and ab initio calculations. For compounds with rather short NN distances the S=C–N–H moiety is non-planar. Dihedral angles as small as 160° are found. The NH chemical shift coefficients measured in non-polar solvents in all the N-substituted-3-piperidinethiopropionamides are more negative (−8 to −17 ppb/K) than in non-hydrogen bonded thioamides. For the latter in non-polar solvents like CDCl₃ and toluene the temperature coefficients are as small as −1 to −4 ppb/K. The large negative effects can be related not only to the non-planarity of the thioamide group in a way that the more pronounced the non-planarity the more negative the temperature coefficients, but also to strong hydrogen bonding and the fact that the acceptor is a nitrogen. For similar amides with non-planar amide groups and nitrogen acceptor large negative temperature coefficients are likewise seen. In polar solvents like DMF the effects in simple thioamides are uniform and close to −6 ppb/K, whereas in the more complex compound like 4p(t) the temperature coefficient is close to 0. An essential feature of measuring temperature coefficients of compounds without strong intramolecular hydrogen bonds in non-polar solvents and at low temperatures is to keep the concentration low enough to avoid dimerisation.     

Robust Speed Control of a Low Damped Electromechanical System Based on CRONE Control: Application to a Four Mass Experimental Test Bench

Robust speed control of a low damped electromechanical system with backlash is studied, controlled load angular speed being not measured. The proposed control strategy combines a Luenberger observer (load angular speed and load torque disturbance estimations) and a robust CRONE controller. The observer provides estimation of the load angular speed and of the disturbance torque applied on the load. Through the computation of only three independent parameters (as many as a PID controller), the CRONE controller permits to ensure the robust speed control of the load in spite of plant parametric variations and speed observation errors. The proposed control strategy is applied to a four mass experimental test bench.     

LES of turbulent heat transfer: proper convection numerical schemes for temperature transport

Large eddy simulations of two basic configurations (decay of isotropic turbulence, and the academic plane channel flow) with heat transfer have been performed comparing several convection numerical schemes, in order to discuss their ability to evaluate temperature fluctuations properly. Results are compared with the available incompressible heat transfer direct numerical simulation data. It is shown that the use of regularizing schemes (such as high order upwind type schemes) for the temperature transport equation in combination with centered schemes for momentum transport equation gives better results than the use of centred schemes for both equations. Copyright © 2004 John Wiley & Sons, Ltd.     

A high‐resolution scheme for low Mach number flows

A method for computing low Mach number flows using high‐resolution interpolation and difference formulas, within the framework of the Marker and Cell (MAC) scheme, is presented. This increases the range of wavenumbers that are properly resolved on a given grid so that a sufficiently accurate solution can be obtained without extensive grid refinement. Results using this scheme are presented for three problems. The first is the two‐dimensional Taylor–Green flow which has a closed form solution. The second is the evolution of perturbations to constant‐density, plane channel flow for which linear stability solutions are known. The third is the oscillatory instability of a variable density plane jet. In this case, unless the sharp density gradients are resolved, the calculations would breakdown. Under‐resolved calculations gave solutions containing vortices which grew in place rather than being convected out. With the present scheme, regular oscillations of this instability were obtained and vortices were convected out regularly. Stable computations were possible over a wider range of sensitive parameters such as density ratio and co‐flow velocity ratio. Copyright © 2004 John Wiley Sons, Ltd.     

Self-bonding in an amorphous polymer below the glass transition: A T-peel test investigation

Films of amorphous polystyrene (PS) with a weight-average molecular weight (M_w) of 225 × 10³ g/mol were bonded in a T-peel test geometry, and the fracture energy (G) of a PS/PS interface was measured at the ambient temperature as a function of the healing time (t_h) and healing temperature (T_h). G was found to develop with (t_h)^1/2 at T_h = T_g-bulk − 33 °C (where T_g-bulk is the glass-transition temperature of the bulk sample), and log G was found to develop with 1/T_h at T_g-bulk − 43 °C ≤ T_h ≤ T_g-bulk − 23 °C. The smallest measured value of G = 1.4 J/m² was at least one order of magnitude larger than the work of adhesion required to reversibly separate the PS surfaces. These three observations indicated that the development of G at the PS/PS interface in the temperature range investigated (<T_g-bulk) was controlled by the diffusion of chain segments feasible above the glass-transition temperature of the interfacial layer, in agreement with our previous findings for fracture stress development at several polymer/polymer interfaces well below T_g-bulk. Close values of G = 8–9 J/m² were measured for the symmetric interfaces of polydisperse PS [M_w = 225 × 10³, weight-average molecular weight/number-average molecular weight (M_w/M_n) = 3] and monodisperse PS (M_w = 200 × 10³, M_w/M_n = 1.04) after healing at T_h = T_g-bulk − 33 °C for 24 h. This implies that the self-bonding of high-molecular-weight PS at such relatively low temperatures is not governed by polydispersity. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1861–1867, 2004     

Study on the Superhydrophilicity of the SiO2-TiO2 Thin Films Prepared by Sol-Gel Method at Room Temperature

Nanoscale SiO₂-TiO₂ composite thin films with the thickness of about 100 nm were prepared by sol-gel method at room temperature in air. The chemical states of the elements on the surface and near the surface were measured by XPS. The results showed that the Ti on/near the surface of the thin films existed not only as TiO₂ but also as Ti₂O₃. Part of the TiO₂ was changed to Ti₂O₃ after UV irradiation. The crystalline structure of the TiO₂ in the SiO₂-TiO₂ thin films was anatase with the crystallite size of 14–20 nm. It was found that the thin film prepared at room temperature in air has good superhydrophilic property and has strong adherence to the substrate.