多夹层板壳的非线性理论及应用（Ⅲ）：扁壳的弯曲和稳定

本文根据文[1]获得的多夹层扁壳非线性基本方程，求解了各种载荷及边界条件下矩形底面多夹层扁壳的非线性弯曲问题，多夹层板、扁柱亮在轴向压力作用下的稳定问题，以及一般形状的扁壳在边界作用力下的变形．     

Ageing of wet-synthesized oxide powders

Wet chemical synthesis of precursor oxide ceramics is a method to obtain small particulate powders. Such powders are far more prone to ageing in air than more traditional precursors. Thermogravimetric analysis is used to highlight the species responsible for the ageing of ceramic precursors. Indeed water and carbon dioxide are observed to evolve from aged powders. Ceramics obtained from aged precursors can reach a very low final density with respect to the theoretical value. A large degree of the original sintering properties can be recovered after washing the aged powders with ethanol in a basic medium.     

SiCp/Y112铝基复合材料制备工艺及性能

3种不同铸造工艺条件下铝基复合材料的微观组织,并对其硬度进行了测定.研究表明:与全液态铸造法和半固态铸造法相比,搅熔铸造制备的SiCp/Y112铝基复合材料,其增强相SiC颗粒分布均匀,气孔率较少.是一种较理想的金属基复合材料制备工艺.未增强的Y112基体铝合金的维氏硬度高于其半固态坯料的维氏硬度;而SiCp/Y112铝基复合材料的维氏硬度明显高于基体的维氏硬度,并随着SiC颗粒的体积分数的增加其复合材料的维氏硬度不断提高.     

Elasticity in nanocrystalline Nd2Fe14B+αFe magnetic composites

The dynamic Young modulus (E) of magnetic Nd₂Fe₁₄B+αFe nanocomposites is investigated with mechanical spectroscopy techniques (vibrating reed configuration, f≈1.5 kHz <10⁻⁶). Reduced values of E are obtained (88–152 GPa) as compared with that predicted by the rule of mixtures for the composite (164 GPa). Three contributions to this reduction are briefly discussed: a large volume fraction of the specimen with grain boundary like structure; internal pores, resulting from the high cooling rate during processing (10⁶ K/min) and magneto-mechanical effects. Even when porosity is identified as the principal cause of modulus reduction, magnetic effects are also detected.     

Damage and fracture evaluation of granular composite materials by digital image correlation method

This paper presents the applications of digital image correlation technique to the mesoscopic damage and fracture study of some granular based composite materials including steelfiber reinforced concrete, sandstone and crystal-polymer composite. The deformation fields of the composite materials resulted from stress localization were obtained by the correlation computation of the surface images with loading steps and thus the related damage prediction and fracture parameters were evaluated. The correlation searching could be performed either directly based on the gray levels of the digital images or from the wavelet transform (WT) coefficients of the transform spectrum. The latter was developed by the authors and showed higher resolution and sensitivity to the singularity detection. Because the displacement components came from the rough surfaces of the composite materials without any coats of gratings or fringes of optical interferometry, both surface profiles and the deformation fields of the composites were visualized which was helpful to compare each other to analyze the damage of those heterogeneous materials. The project supported by the National Natural Science Foundation of China (10125211 and 10072002), the Scientific Committee of Yunnan Province for the Program of Steel Fiber Reinforced Concrete, and the Institute of Chemical Materials, CAEP at Mianyang     

Synthesis and orientation study of a magnetically aligned liquid‐crystalline chitin/poly(acrylic acid) composite

A high magnetic field of 5 T was used to fabricate a magnetically aligned, optically anisotropic, liquid‐crystalline chitin/poly(acrylic acid) composite. The aligned mesophase was fixed by photoinitiated free‐radical polymerization. From an examination of polarized optical micrographs and an X‐ray diffraction study, a high degree of orientation of 0.70 was observed for the composite with a higher liquid‐crystalline chitin concentration (10.70 wt %); the orientation was reduced with a decreased chitin concentration at a given acrylic acid concentration. The X‐ray data for the developed composite showed a uniplanar orientation for the chitin crystallites, with its molecular long axes perpendicular to the direction of the magnetic field. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 711–714, 2003     

Material-Adapted Design of Textile-Reinforced Composite Structures with Optimized Vibro-Acoustic and Damping Properties Including Shear Effects

Advanced analytical models have been developed at the ILK, which offer a possibility of calculating the vibro-acoustic and damping behavior of textile-reinforced composite shells and plates with account of shear effects. The simulation models elaborated have been verified on selected examples, and the analytical results were fully corroborated by accompanying numerical calculations for typical lay-ups.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 289–302, May–June, 2005.     

Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

Synthesis,characterization, and electrical properties of polypyrrole/multiwalled carbon nanotube composites

Size‐controllable polypyrrole (PPy)/multiwalled carbon nanotube (MWCNT) composites have been synthesized by in situ chemical oxidation polymerization directed by various concentrations of cationic surfactant cetyltrimethylammonium bromide (CTAB). Raman spectra, FTIR, SEM, and TEM were used to characterize their structure and morphology. These results showed that the composites are core (MWCNT)–shell (PPy) tubular structures with the thickness of the PPy layer in the range of 20–40 nm, depending on the concentration of CTAB. Raman and FTIR spectra of the composites are almost identical to those of PPy alone. The electrical conductivities of these composites are 1–2 orders of magnitude higher than those of PPy without MWCNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6449–6457, 2006     

Effect of the pore surface modification of an inorganic substrate on the plasma‐grafting behavior of pore‐filling‐type organic/inorganic composite membranes

We have investigated the effect of the surface state and surface treatment of the pores of an inorganic substrate on the plasma‐grafting behavior of pore‐filling‐type organic/inorganic composite membranes. Shirasu porous glass (SPG) was used as the inorganic substrate, and methyl acrylate was used as the grafting monomer. The grafting rate increased as the density of silanol on the SPG substrate increased. This result suggests that radicals are generated mainly at the silanol groups on the pore surface by plasma irradiation. The SPG substrates were treated with silane coupling agents used to control the mass of organic material bonded to the pore surface. The thickness of the grafted layer became thinner as the mass of organic material bonded to the pore surface of SPG increased. This decrease in the thickness of the grafted layer could be explained by the decrease in the penetration depth of vacuum ultraviolet rays contained in plasma having a wavelength of less than 160 nm that generated radicals in the pores of the substrate. The thickness of the grafted layer inside the SPG substrates could be controlled through the control of the mass of organic material bonded to the pore surface of the SPG substrate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 846–856, 2006