Relative Intensity Noise in Optical Single Side Band Systems with Multiple In-Line Amplifiers: Analysis and Validation

Abstract

This article analyzes and validates through simulation the influence of fiber nonlinearity, dispersion, and loss on the Relative Noise Intensity (RIN) spectrum at fiber output in externally modulated optical single side band (OSSB) systems. The analysis includes the RIN generated by the laser source, the effect of the OSSB modulator, and noise generated by the in-line optical amplifiers. The analysis takes into account conversion between phase noise and intensity noise introduced by fiber transmission. It is shown that, depending on the operating conditions, the system performance may be predominantly affected either by the laser RIN or by the noise generated by the in-line optical amplifiers. The impact of the OSSB modulator can be relevant when the RIN of the system is dominated by the laser noise and should therefore be considered.     

Probability of fatigue failure in glass fibers

Abstract

Fracture mechanics provides the background for making long-term failure predictions to assure the mechanical reliability of glass fibers. The fatigue parameters necessary for making these predictions can be obtained from static and dynamic fatigue strength experiments. The failure calculations are best understood by expressing the predictions in terms of a design diagram. The probability of failure in service as well as the proof test stress necessary to ensure a minimum lifetime in service can be obtained from a design diagram.     

Relation between interfacial shear strength and compressive strength of carbon fiber/epoxy resin composite strands

The mechanism with which the fiber-matrix interfacial strength exerts its influence on the compressive strength of fiber reinforced composites has been studied by measuring the axial compressive strength of carbon fiber/epoxy resin unidirectional composite strands having different levels of interfacial shear strength. The composite strands are used for experiments in order to investigate the compressive strength which is not affected by the delamination taking place at a weak interlayer of the laminated composites. The interfacial strength is varied by applying various degrees of liquid-phase surface treatment to the fibers. The efficiency of the compressive strength of the fibers utilized in the strength of the composite strands is estimated by measuring the compressive strength of the single carbon filaments with a micro-compression test. The compressive strength of the composite strands does not increase monotonically with increasing interfacial shear strength but showes lower values at higher interfacial shear strengths. With increasing interfacial shear strength, the suppression of the interfacial failure in the misaligned fiber region increases the compressive strength, while at higher interfacial shear strengths, the enhancement of the crack sensitivity decreases the compressive strength.     

Fabrication of continuous fiber-reinforced thermoplastic composites with structural gradient from sheath-core type bicomponent fibers

Sheath-core type bicomponent fibers of polypropylene (PP) as a sheath component and thermotropic liquid crystalline polymer (TLCP) as a core component were prepared by the highspeed melt spinning process. Continuous fiber reinforced thermoplastic composites, in which TLCP acts as a reinforcing fiber and PP as a matrix polymer, were fabricated by the compression molding of these fibers. In the melt spinning, the attainable highest take-up velocity of TLCP was improved by co-processing with PP. Tensile modulus and strength of the TLCP component in the PP/TLCP bicomponent fibers increased with an increase in the take-up velocity. Comparison of wide-angle X-ray diffraction patterns of starting bicomponent fibers and fabricated composites indicated that the orientation relaxation of TLCP did not occur in the compression molding process. Accordingly, the tensile modulus and strength of the PP/TLCP composites were similar to those of the bicomponent fibers. Continuous fiber reinforced thermoplastic composites with various types of fiber content distributions were fabricated from the bicomponent fibers in which sheath-core composition was changed gradually in the spinning process. In the three-point bending test, the composites with two different types of symmetric structural gradients, one with higher TLCP fiber content near the surfaces than in the center and the other with higher TLCP content in the center than near the surfaces, exhibited different flexural moduli even though the overall TLCP contents were comparable. In the three-point bending test of a composite with asymmetric structural gradient, the yielding behavior and maximum flexural load varied depending on the direction of load application although the initial flexural moduli were similar.     

啁啾相移光纤光栅分布式应变与应变点精确定位传感研究

利用啁啾相移光纤光栅狭缝的中心波长对应变点和应变量的波长敏感性,实现应变与应变点精确定位的传感.当啁啾光纤光栅上的某一位置产生微应变时,该应变点会产生相移,其频谱则会出现一个与之对应的狭缝,且狭缝的深度和中心波长与应变的大小和位置相关.当串接不同中心波长的啁啾光纤光栅后,即可实现一定范围内的分布式应变与应变点精确定位检测.本文通过V-I传输矩阵法建立了狭缝深度和中心波长关于应变量和应变位置的理论模型,分析结果表明理论上可以实现微米量级的精确定位.搭建了级联啁啾相移光纤光栅的分布式应变传感装置,实验获得的最大应变灵敏度为0.19 pm/με.该精确定位传感装置在先进制造、精密加工、航空航天、铁路系统等高新技术领域具有重要的应用前景.     

Fibre gratings and devices for sensors and lasers

Although mainstream grating writing, more often than not using single photon excitation of germanosilicate based defects with CW 244 nm light, remains the key technology for complex devices it is now being complemented by a whole host of processes which can enhance and tailor the properties of both conventional and not‐so‐conventional fibre Bragg gratings. Further, processes for writing of gratings in non‐germanosilicate fibres have also continued to develop and include multi‐photon excitation directly into the band edge of the glass. It is now possible to custom tailor a gratings property based on the application and the nature of production as well as custom tailor the grating writing process to suit the type of fibre and application. Examples and suggestions where these can benefit sensors and lasers are outlined.     

Theoretical and experimental investigation of thermal effects in a high power Yb-doped double-clad fiber laser

In this paper, based on the thermal conduction equations and the steady-state rate equations, a theoretical and numerical analysis of thermal effects is investigated for a single end pumped Yb-doped double-clad fiber laser (YDDC). The distributions of signal power and temperature for different pump powers and fiber parameters are compared. According to the results, the parameters of the optical-cavity have been optimized and an effective method has been adopted to reduce the thermal effects in an experimental investigation. As a result, an output power of 621 W has been obtained with a slope efficiency of 78%.     

A High Efficiency Yb3+-doped Fiber Ring Cavity Laser with Narrow Line-widthRound-trip Dispersion Calculation for Martinez Pulse Stretcher

A novel Yb3+-doped fiber ring cavity laser pumped by a 977 nm laser diode is presented with its output laser wavelength of 1060 nm. Based on a fiber Bragg grating (FBG), the laser exhibits 0.20 nm line-width, 7.5 mW laser output power, 40 dB signal-to-noise ratio (SNR) and 66% slope efficiency.This paper proposed a ray-tracing model for the Martinez stretcher, derived the calculation formulae for the stretcher of a grating-spherical mirror system and discussed the error for the total dispersion resulted from the spatial dispersion. The calculated results show that the error could be ignored for the beam returned to the stretcher for the second pass in the wavelength range of 750 nm and 850 nm.     

贵金属纳米结构为敏感层的锥形光纤探针及其SERS活性

表面等离激元纳米结构与便携式光纤拉曼系统相结合,在液体样品和生物活体组织的快速、实时监测上有较好的应用前景。其核心技术是将具有表面增强拉曼散射(SERS)活性的贵金属纳米结构耦合到光纤探针表面。本文基于共价键结合原理,将3-巯丙基三甲氧基硅烷通过与锥形光纤探针表面的硅羟基形成共价键修饰在光纤上;同时,硅烷偶联剂末端的巯基与金或银纳米结构形成Au-S或Ag-S共价键,将金纳米粒子和银纳米立方体牢牢吸附到光纤探针表面。这种SERS光纤探针具有很高的稳定性(SERS信号相对标准偏差低于3%),对农残甲基对硫磷的敏感度达到10纳摩尔,对污染物的远程、便携式在线检测具有重要意义。     

基于光纤振动安全预警系统的振源识别算法研究

光纤振动预警系统可自动采集周边振动信号,面对大量复杂的振动信号,如何准确识别目标振源是系统研究的难点。针对光纤振动安全预警系统采集到的振动信号进行属性特征分析,建立相应的特征模型,并建立振源属性特征模型,包括识别下雨振源的能量信息熵模型,以及区分机械施工和车辆经过振源的基频稳定性模型等。通过振源识别算法,提高了振源类型识别的准确性。测试结果表明,特征模型的设计和选择合理,识别准确率高。