Bounds to optimal burn‐in and optimal work size

Burn‐in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, we consider the problem of determining the optimal burn‐in time and optimal work size maximizing the long‐run average amount of work saved per time unit in the computer applications. Assuming that the underlying lifetime distribution of the computer has an initially decreasing or/and eventually increasing failure rate function, an upper bound for the optimal burn‐in time is derived for each fixed work size and a uniform (with respect to the burn‐in time) upper bound for the optimal work size is also obtained. Furthermore, it is shown that a non‐trivial lower bound for the optimal burn‐in time can be derived if the underlying lifetime distribution has a large initial failure rate. Copyright © 2005 John Wiley & Sons, Ltd.     

A subdomain boundary element method for high‐Reynolds laminar flow using stream function‐vorticity formulation

The paper presents a new formulation of the integral boundary element method (BEM) using subdomain technique. A continuous approximation of the function and the function derivative in the direction normal to the boundary element (further ‘normal flux’) is introduced for solving the general form of a parabolic diffusion‐convective equation. Double nodes for normal flux approximation are used. The gradient continuity is required at the interior subdomain corners where compatibility and equilibrium interface conditions are prescribed. The obtained system matrix with more equations than unknowns is solved using the fast iterative linear least squares based solver. The robustness and stability of the developed formulation is shown on the cases of a backward‐facing step flow and a square‐driven cavity flow up to the Reynolds number value 50 000. Copyright © 2004 John Wiley & Sons, Ltd.     

Viscosity,particle size distribution,and structural investigation of tetramethyloxysilane/2‐hydroxyethyl methacrylate sols during the sol–gel process with acid and base catalysts

The tetramethoxysilane (TMOS)/2‐hydroxylethyl methacrylate (HEMA) hybrid gels were synthesized with acid and base catalysts, via the in situ polymerization of HEMA, with and without the cosolvent methanol. With methanol in the TMOS/HEMA sol, the enhanced esterification and depolymerization reactions of the silanols resulted in a slower growth of silica particles. The silica particles that were synthesized with an acid catalyst were less than 40 nm. The thermal resistance of the poly(2‐hydroxyethyl methacrylate) (PHEMA) chains was enhanced by the addition of colloidal silica. The Fourier transform infrared characterizations and the exothermal peaks on the differential scanning calorimetry traces of these hybrid gels indicated chemical hybridization occurring as a result of condensation of the colloid silica and PHEMA at higher temperatures. Hence, the residual weight content of the hybrid gel after its synthesis with the base catalyst was even higher than the content of TMOS in the hybrid sol. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3476–3486, 2004     

Study on the Superhydrophilicity of the SiO2-TiO2 Thin Films Prepared by Sol-Gel Method at Room Temperature

Nanoscale SiO₂-TiO₂ composite thin films with the thickness of about 100 nm were prepared by sol-gel method at room temperature in air. The chemical states of the elements on the surface and near the surface were measured by XPS. The results showed that the Ti on/near the surface of the thin films existed not only as TiO₂ but also as Ti₂O₃. Part of the TiO₂ was changed to Ti₂O₃ after UV irradiation. The crystalline structure of the TiO₂ in the SiO₂-TiO₂ thin films was anatase with the crystallite size of 14–20 nm. It was found that the thin film prepared at room temperature in air has good superhydrophilic property and has strong adherence to the substrate.     

能动反射镜低频像差补偿能力分析

 采用Algor软件包并利用有限元法对37单元能动反射镜低频误差补偿能力进行了分析计算，确定了镜面厚度8mm，驱动器间距46mm，极头直径12mm等能动反射镜制造的关键参数。通过计算机仿真分析证明，基于这些参数所设计的能动反射镜可以对低频误差进行有效校正，校正精度的均方根值小于等于λ／８，从而可以为能动反射镜的制造提供理论依据。     

Analysis of end point vibrations of a two-link manipulator by integrated CAD/CAE procedures

In this work, the effect of flexibility on the trajectory of a planar two-link manipulator is studied using integrated computer-aided design/analysis (CAD/CAE) procedures. The solid models and finite element models of the parts of the manipulator are created by using the CAD/CAE software I-DEAS. The assembly is defined, and knowing the payload and the end point trajectory, the velocities and accelerations of the parts, joint forces and driving torques are calculated using the rigid body dynamics. All the time dependent nodal forces acting on the parts including distributed gravity and inertia forces are created in files with the I-DEAS program file format. The finite element vibration analysis of the parts is performed by I-DEAS. The end point vibrations and the deviations from the rigid-body trajectory are analyzed for different types of end point acceleration curves. A circular trajectory is considered as an example. It is observed that the precision of the manipulator can be increased by testing different end point acceleration curves without changing the trajectory and the duration of the end point work. The procedure explained in this work can be used for this purpose successfully.     

Sufficient conditions of non‐uniqueness for the Coulomb friction problem

We consider the Signorini problem with Coulomb friction in elasticity. Sufficient conditions of non‐uniqueness are obtained for the continuous model. These conditions are linked to the existence of real eigenvalues of an operator in a Hilbert space. We prove that, under appropriate conditions, real eigenvalues exist for a non‐local Coulomb friction model. Finite element approximation of the eigenvalue problem is considered and numerical experiments are performed. Copyright © 2003 John Wiley & Sons, Ltd.     

美式期权定价中非局部问题的有限元方法

在本文中 ,我们关心的是美式期权的有限元方法 .首先 ,根据 [4 ]我们对所讨论的问题引进一个新奇的实用的方法 ,它涉及到对原问题重新形成准确的数学公式 ,使得数值解的计算可以在非常小的区域上进行 ,从而该算法计算速度快精度高 .进而 ,我们利用超逼近分析技术得到了有限元解关于 L2 -模的最优估计 .     

Research on sound radiation from body in free field

I.IntroductionWhenastructurcvibratcs,itsvibratingsurfacewillmakesurroundingmediummovetogethcrwithit.Ifthernotionissofastthatthcmediumroundthestructureproduccaloca1contractionandcxpansionandthcypropagatefaraway,thesoundradiationisformed.Itispossiblctodcscribeanalytica11ytheradiationfic1dofsimplyandregularlyshapcdsourcessuchaspointsoundsourccs,spherica1soundsourccsandinflnite1engthllnearsoundsourccs,butitisa1mostimpossib1ctosolvetheradiationfiledbyanyanalyt-ica1methodforsourcesofvcrycomplicateds…     

一种新型的二元光学器件——多位相光束分束器的制作

本文报道了用于多光束分束器的反射式16位相值二元光学器件的制作。该二元光学器件把一束光束分成5×5光束阵列。测量的衍射效率为76.16%,接近理论设计值79.68%。该二元光学器件的有效孔径为10mm×10mm。