电感耦合等离子体原子发射光谱法测定中药方剂煎煮液中的微量元素

本文采用HNO3－H2O2对中药方剂煎煮液进行处理，拟定了电感耦合等离子体原子发射光谱法同时测定试样中12个微量元素的方法，选择了仪器的最佳工作条件，考察了基本效应的影响。在选定条件下，12个微量元素的检出限为0．10－5．0ng/g，相对标准偏差为0.10%-9.5%(n=10),加标回收率为85％－103％。该方法简单、快速，已用于大量样品的检测，分析结果满意。     

Finite Element Solution of Conical Diffraction Problems

This paper is devoted to the numerical study of diffraction by periodic structures of plane waves under oblique incidence. For this situation Maxwell's equations can be reduced to a system of two Helmholtz equations in R ² coupled via quasiperiodic transmission conditions on the piecewise smooth interfaces between different materials. The numerical analysis is based on a strongly elliptic variational formulation of the differential problem in a bounded periodic cell involving nonlocal boundary operators. We obtain existence and uniqueness results for discrete solutions and provide the corresponding error analysis.     

锐钛矿二氧化钛超细纳米晶的三声子互作用

本文通过对粒径为2.2-25.5nm的锐钛矿二氧化钛超细纳米晶在83-293 K温度范围内的变温拉曼光谱的研究,得到了三声子互作用对拉曼频率和线宽的贡献随粒径的变化关系。结果表明锐钛矿二氧化钛超细纳米晶的三声子相互作用随粒径减小而加强。     

Stress-Strain State in the Zone of Load Transfer in a Composite Specimen under Uniaxial Tension

The stress-strain state in the zone of load transfer in a uniaxially stretched specimen made of a unidirectional epoxy carbon-fiber-reinforced plastic (CFRP) is investigated. A parametric analysis of the influence of geometric and mechanical characteristics of the specimen on its stress-strain state is performed by means of finite-element modeling. The parameters allowing us to significantly reduce the dangerous concentration of transverse and tangential stresses are revealed. The mechanical tensile characteristics of a high-strength pultruded unidirectional CFRP are determined experimentally, and the size effect of its strength is estimated.     

A Generalization of the Mean Size Formula of Wavelet Packets in Lp

The purpose of this paper is to investigate the mean size formula of wavelet packets in Lp for 0 〈 p ≤ ∞. We generalize a mean size formula of wavelet packets given in terms of the p-norm joint spectral radius and we also give some asymptotic formulas for the Lp-norm or quasi-norm on the subdivision trees. All results will be given in the general setting,     

CFD在燃煤细粒子凝聚过程中的应用

燃煤产生的细粒子富集了大量的有毒痕量元素,对大气环境和人类健康造成严重危害。本文针对燃煤细粒子的形成过程,在计算流体力学(CFD)的基础上,结合气溶胶动力学理论,模拟了烟气中细粒子在圆柱形流场中由于碰撞而凝聚的过程,并通过计算结果分析细粒子颗粒特征参量(速度、质量、直径和颗粒数目)随流场的变化趋势,为深入研究燃煤细粒子的形成演化机理提供理论基础。     

Magnetic poly(N‐isopropylacrylamide) microspheres by dispersion and inverse emulsion polymerization

The aim of this study was to develop novel thermally responsive polymer microspheres with magnetic properties. Dispersion and inverse emulsion copolymerization of N‐isopropylacrylamide (NIPAAm) and N,N′‐methylenebisacrylamide (MBAAm) was investigated in the presence of γ‐Fe₂O₃ nanoparticles. The resulting microspheres were characterized in terms of morphology, size, polydispersity, iron content, and temperature‐dependent swelling using optical microscopy, transmission electron microscopy, scanning electron microscopy, QELS, and AAS. The effects of several variables, such as the concentration of γ‐Fe₂O₃, MBAAm crosslinking agent, Span 80 surfactant, 2,2′‐azobis(2‐methyloctanenitrile) (AMON) initiator, and polymerization temperature on the properties of the microspheres were studied. Swelling and thermoresponsive behavior of the microspheres containing γ‐Fe₂O₃ nanoparticles were also investigated. The microspheres contained about 8 wt % of iron. The presence of magnetic nanoparticles and their concentration changes did not have any significant effect on the temperature sensitivity of the composites. The particles gradually shrink into an increasingly collapsed state when the temperature is raised to 40 °C since the increase in temperature weakens the hydration and PNIPAAm chains gradually become more hydrophobic, which leads to the collapse of the particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5884–5898, 2007     

Numerical Prediction of the Strain State of Thermoset Matrix/Mineral Filler Composite Plates

The numerical prediction of the fields of inelastic strains (the linear invariant of the tensor of inelastic strains) in thermoset polyester/marble filler composite plates is discussed. A uniformly distributed load is applied to the plates, which lie on a steel base. The strain fields are predicted by means of the boundary element method by using creep test data for the composites and the polyester matrix itself. Identical creep tests were performed for two ages of the materials (1 month and 13 years), which allowed evaluating the aging effect. The study is carried out in two stages. At the first stage, the application of the generalized Maxwell-Gurevich equation to the thermoset matrix/mineral filler composite is demonstrated. The model parameters determined from the experimental creep data is used for the second stage, where the state of inelastic strains in the plates is predicted by applying the boundary element method. The influence of composite formulation (filler content) and physical aging of the polyester matrix on the state of inelastic strains in the plates is shown.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 145–156, March–April, 2005.     

Bounds to optimal burn‐in and optimal work size

Burn‐in is a widely used method to improve the quality of products or systems after they have been produced. In this paper, we consider the problem of determining the optimal burn‐in time and optimal work size maximizing the long‐run average amount of work saved per time unit in the computer applications. Assuming that the underlying lifetime distribution of the computer has an initially decreasing or/and eventually increasing failure rate function, an upper bound for the optimal burn‐in time is derived for each fixed work size and a uniform (with respect to the burn‐in time) upper bound for the optimal work size is also obtained. Furthermore, it is shown that a non‐trivial lower bound for the optimal burn‐in time can be derived if the underlying lifetime distribution has a large initial failure rate. Copyright © 2005 John Wiley & Sons, Ltd.     

A subdomain boundary element method for high‐Reynolds laminar flow using stream function‐vorticity formulation

The paper presents a new formulation of the integral boundary element method (BEM) using subdomain technique. A continuous approximation of the function and the function derivative in the direction normal to the boundary element (further ‘normal flux’) is introduced for solving the general form of a parabolic diffusion‐convective equation. Double nodes for normal flux approximation are used. The gradient continuity is required at the interior subdomain corners where compatibility and equilibrium interface conditions are prescribed. The obtained system matrix with more equations than unknowns is solved using the fast iterative linear least squares based solver. The robustness and stability of the developed formulation is shown on the cases of a backward‐facing step flow and a square‐driven cavity flow up to the Reynolds number value 50 000. Copyright © 2004 John Wiley & Sons, Ltd.