Microstructure change in deuterium implanted CLAM steel induced by electron irradiation

As Reduced Activation Ferritic/Martensitic (RAFM) steel is considered the primary candidate for use as a structural material in fusion power reactors,many countries are developing different kinds of RAFM.China is developing new CLAM (China Low Activation Martensitic) steel.The study investigates microstructural changes in CLAM steel implanted with deuterium ions induced by 1250 keV electron irradiation from R.T.to 873 K,and observes both the growth and shrinkage of the defect clusters produced by deuterium ...     

Application of electromagnetic processing for development of high-performance sintered powder metal parts

Electromagnetic processing was used to study the effects of electro-magneto forming on the dimensional control and thermal stability of sintered powder metal (PM) parts. The investigation was carried out on sinter-hardened, low chromium-molybdenum bainitic steel. The results show an increase in the microhardness of about 14% for the electromagnetic processed parts compared to the as-sintered parts. This was attributed to the 2% increase in the density, 17% and 29% reduction in the volume fraction of porosity and width of the bainitic lath, respectively, due to the electromagnetic processing. Dimensional characterization was carried out using a vertically aligned push-rod dilatometer. After four thermal cycles of heating and cooling, at a controlled rate of 5 °C/min to 1000 °C, the electromagnetic processed parts exhibited reduced dimensional change of about 44% lower than for the as-sintered parts. This is significantly important for applications that demand high dimensional tolerance and performance, especially at elevated temperatures.     

特种合金钢系列标准物质研制

介绍了特种合金钢系列标准物质的研制过程。采用合理的冶炼锻轧工艺,选取不同部位的样品进行均匀性检验,确定了15种元素的认定值及扩展不确定度,并进行了线性、一致性考察以及与国内外同类标准物质的比对。结果表明,本套特种合金钢系列标准物质的均匀性良好,定值准确且有良好的梯度分布。     

Xanthione: A new and effective corrosion inhibitor for mild steel in sulphuric acid solution

The adsorption and inhibition effect of xanthione (XION) on mild steel in 0.5 M H₂SO₄ at 303–333 K were studied using gravimetric and UV–visible spectrophotometric methods. The results obtained show that XION acts as an effective corrosion inhibitor for mild steel in sulphuric acid and inhibition efficiency reaches 98.0% at a very low inhibitor concentration of 10 μM. Inhibition efficiency was found to increase with increase in XION concentration but decreased with temperature suggesting physical adsorption mechanism. Arrhenius law and its transition equation lead to estimate the activation parameters of the corrosion process. XION inhibits the corrosion of mild steel effectively at moderate temperature and adsorbs according to the Langmuir isotherm. Thermodynamic parameters governing the adsorption process have been calculated and discussed. The UV–visible absorption spectra of the solution containing the inhibitor after the immersion of mild steel specimen indicate the formation of a XEN–Fe complex. Attempt to correlate the molecular structure to quantum chemical indices was made using density functional theory (DFT).     

Adsorption and Corrosion Inhibition Behavior of Schiff Base-Based Cationic Gemini Surfactant on Mild Steel in Formic Acid

The adsorption and corrosion inhibition behavior of synthesized Schiff base-based cationic gemini surfactant bis[p-(N,N,N-tetradecyldimethylammonium bromide)benzylidene]thiourea (14-S-14) on mild steel in 20% formic acid in the temperature range of 30°C to 60°C was evaluated using weight loss measurements, solvent analysis of iron ions and potentiodynamic polarization measurements. The synthesized inhibitor was characterized using Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance spectroscopy (NMR), and thin layer chromatography (TLC). The surface morphology of the corroded mild steel specimen was evaluated using scanning electron microscopy (SEM), energy dispersive x-ray analysis (EDAX), and atomic force microscopy (AFM). Thermodynamic/kinetic parameters were calculated to elaborate the adsorption and corrosion inhibition mechanism of the inhibitor. The inhibition efficiency of the compound was found to vary with inhibitor concentration, immersion time, and temperature. The adsorption of the compound on the steel surface was found to obey Langmuir adsorption isotherm.      

Influence of Molecular Weight on Mild Steel Corrosion Inhibition Effect by Polyvinyl Alcohol in Hydrochloric Acid Solution

The corrosion inhibition of mild steel in hydrochloric acid solution in the presence of three different molecular weights of polyvinyl alcohol (PVA) designated as PVA-I, PVA-II, and PVA-III corresponding to 14,000, 72,000, and 125,000 g mol^?1, respectively, was investigated using electrochemical impedance spectroscopy, linear polarization resistance (LPR), and potentiodynamic polarization techniques at 25°C. It was found that PVA of different molecular weights inhibited the corrosion of mild steel in the acid environment. Inhibition efficiency (η%) increases with increase in concentration of the polymers. LPR measurements clearly show that inhibition efficiency increases with increasing molecular weight in the order PVA-III > PVA-II > PVA-I. Polarization curves indicate that PVA functions as a mixed inhibitor affecting both the anodic metal dissolution and cathodic hydrogen evolution partial reactions of the corrosion process. The experimental data obtained fitted well into Langmuir adsorption isotherm model. Physical adsorption mechanism is proposed from the thermodynamic (free energy of adsorption) parameters obtained.     

Experimental and Theoretical Studies on Synthesized Compounds as Corrosion Inhibitor for Mild Steel in Hydrochloric Acid Solution

Imidazole derivatives, namely, 1-((1-(piperazinomethyl)-1H-benzoimidazol-2-yl)methyl)-2-phenylhydrazine (PBIP), and 1-((1-(morpholinomethyl)-1H-benzoimidazol-2-yl)methyl)-2-phenylhydrazine (MBIP) were synthesized and investigated as inhibitors for mild steel corrosion in 15% HCl solution using weight loss, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. It was found that the inhibition efficiency of both the inhibitors increases with increase in concentration of inhibitors and decreases with increase in temperature. The inhibitors, PBIP and MBIP, show corrosion inhibition efficiency of 92.6% and 91.4% at 300 ppm concentration, respectively, at 303 K. Polarization studies showed that both the studied inhibitors were of mixed type in nature. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were performed for surface study of uninhibited and inhibited mild steel samples. The semi-empirical AM1 method was employed for theoretical calculations.     

Development of a solid‐phase microextraction fiber by the chemical binding of graphene oxide on a silver‐coated stainless‐steel wire with an ionic liquid as the crosslinking agent

Graphene oxide was bonded onto a silver‐coated stainless‐steel wire using an ionic liquid as the crosslinking agent by a layer‐by‐layer strategy. The novel solid‐phase microextraction fiber was characterized by scanning electron microscopy, energy‐dispersive X‐ray spectroscopy and Raman microscopy. A multilayer graphene oxide layer was closely coated onto the supporting substrate. The thickness of the coating was about 4 μm. Coupled with gas chromatography, the fiber was evaluated using five polycyclic aromatic hydrocarbons (fluorene, anthracene, fluoranthene, 1,2‐benzophenanthrene, and benzo(a)pyrene) as model analytes in direct‐immersion mode. The main conditions (extraction time, extraction temperature, ionic strength, and desorption time) were optimized by a factor‐by‐factor optimization. The as‐established method exhibited a wide linearity range (0.5–200 μg/L) and low limits of determination (0.05–0.10 μg/L). It was applied to analyze environmental water samples of rain and river water. Three kinds of the model analytes were quantified and the recoveries of samples spiked at 10 μg/L were in the range of 92.3–120 and 93.8–115%, respectively. The obtained results indicated the fiber was efficient for solid‐phase microextraction analysis.