A Scanning Electron Microscopy study of water in soil

Cold stage Scanning Electron Microscopy (SEM) with a rapid cooling technique makes it possible to investigate the water phase within unsaturated porous media. It is thought that this technique preserves the main features of the micromorphology of the water menisci as it exists in the liquid phase in soils. Saddle-shaped elements, as well as pendular rings of water, were observed with concave and convex curvatures of the water-air interface. The hydraulic conductivity of an unsaturated soil may be inferred from SEM photographs. Observations of isolated water menisci indicate the existence of an immobile water domain. The surface geometry of the water menisci was analyzed quantitatively and surface tension and capillary pressure were determined.     

On the deformation and fracture of porous materials

The constitutive behavior of porous materials (including the yield loci, the void growth rate, the macro stress-strain relation and the strain to localization instability) is examined based on the lower bound approach proposed by the present authors. These results are then compared with the experimental and the finite element results as well as those predicted by Gurson's equations. Emphasis is placed on approaching the real behavior from the upper and the lower bound analysis. Calculation is also made on the influence of void nucleation on the critical strain to instability and a modified strain-controlled nucleation criterion is proposed. Finally the instability and fracture of AISI4340 steel in plane strain tension is examined and comparison is made between theoretical and experimental results.     

含氰基的酚醛树脂及其碳纤维复合材料

含氰基的酚醛树脂，具有优异的耐高温性能和高温下的机械强度，在３１５℃下性能变化甚小；不着火，发烟量低，有良好的加工成型性能。热固化过程中氰基成三嗪环而交联，没有小分子脱出，是一类具有广泛发展前景的新型热固性树脂。     

Thermoanalytical procedures to identify the morphology of polycrystalline materials

Polypropylenes of differing morphologies were examined by differential thermal analysis. The problems of reordering during the programmed heating are discussed. Four potential procedures by which the reordering could be inhibited are considered, and three of these are experimentally assessed. Their advantages and deficiencies are identified. Two pretreatments, an etching and a crosslinking, are recognised as able to qualitatively characterise the initial morphology, with a preference for the former. A test to identify the occurrence of reordering is identified. In celebration of the 60^th birthday of Dr. Andrew K. Galwey     

An efficient lasing action from pyrromethene 556 dye-doped organically modified silicates

Organically modified solid-state silicates (ORMOSILS) doped with a new laser dye 1,3,5,7,8-pentamethylpyrromethene-2,6-disulfonate-BF₂ complex (pyrromethene 556) have been synthesized by a sol-gel method and the compositional effects on pore characteristics, fluorescence and lasing properties have been investigated. It is found that the use of dimethylsulfoxide and γ-glycidoxypropyltrimethoxysilane could greatly change the structure properties of sol-gel derived ORMOSILS cage, and thus the fluorescence and lasing properties of the materials could improve significantly. A successful laser oscillation from this dye-doped ORMOSILS sample has been achieved upon pumping with a Q-switched frequency-doubled Nd:YAG laser at 532 nm. A slope efficiency of 54% with a useful lifetime greater than 10,000 shots has been demonstrated at a pump repetition rate of 1 Hz and a pump intensity of 1 J/cm² by using the new ORMOSILS cage on our newly designed laser system. Our results have shown that it is possible to obtain a high-efficiency with a long-lifetime for a compact new laser device by low cost dye-doped solid-state ORMOSILS.     

High-T c superconducting magnetic bearings for rotation-based devices

Summary A Modified-Melt-Powder-Melt-Growth (MMPMG) technique has been developed for the preparation of melt-textured Y-Ba−Cu−O pellets. To test their performances, the samples were characterized with respect to their microstructure, pinning strength and interaction force with permanent magnets. A superconducting magnetic bearing was built and integrated in a levitating flywheel system for energy storage. Paper presented at the “VII Congresso SATT?, Torino, 4–7 October 1994. Under a Fondazione Confalonieri grant.     

Progress in the quality assurance of environmental trace organic analysis

An overview is given on the stepwise learning programmes undertaken to identify the main sources of error associated with the determination of the mandatory organic contaminants in the marine monitoring programmes. Details are given on the preparation and use of LRMs and CRMs to maintain analytical control and quantify the laboratory errors in relation to the measurement of changes in the environment.     

Optimum Gas Journal Bearing with the Flexible Surface

The optimum shape of the cylindrical internal deformable (flexible) surface of a gas journal bearing of infinite length is designed. The variational problem of determining the clearance shape giving the maximum bearing load capacity is formulated and solved.     

FexNi100−x nanometric films deposited by laser ablation on SiO2/Si substrates

Fe_xNi_100−x nanometric films were deposited on SiO₂/Si substrates at room temperature using the pulsed laser deposition technique. The targets were Fe-Ni amorphous magnetic foils with composition Fe₅₀Ni₅₀, Fe₃₅Ni₆₅ and Fe₂₂Ni₇₈. Morphological and structural properties of the deposited films were investigated using scanning electron microscopy, Rutherford backscattering spectrometry, grazing incidence X-ray diffraction, and X-ray reflectivity. Electrical and magnetic characteristics of the films were investigated by using the four-point probe and the magneto-optic Kerr effect techniques, respectively. The film properties are strictly dependent on the Fe-Ni compositional ratio.