球形WC增强铁基复合等离子堆焊层的组织与摩擦学性能

为提高304不锈钢的摩擦学性能,将质量分数为30%和60%的球形WC添加到铁基复合粉末,采用等离子堆焊技术在其表面制备了WC增强铁基复合涂层.分析其显微组织结构、物相和显微硬度,在恒定载荷(50 N)和滑动速度(20 mm/s)下进行干摩擦磨损试验,研究其干滑动摩擦学性能.结果表明:富含Cr的固溶强化奥氏体、高硬度的Cr7C3和WC增强相的存在,提高了WC增强铁基堆焊层的硬度,30%WC和60%WC涂层的显微硬度达到HV0.2665和HV0.2724,比铁基涂层提高了21.1%和31.9%,是304基体的3.7和4倍;30%WC和60%WC涂层的摩擦系数和磨损率分别为0.59和2.639×10~(–6) mm~3·N~(–1)·m~(–1),0.42和1.111×10~(–6) mm~3·N~(–1)·m~(–1).30%WC和60%WC涂层均表现出优异的耐磨性能,其磨损机理分别为黏着磨损和二体磨粒磨损的混合机制,和三体磨粒磨损.     

柔性ZnNi/Al-LDHs/碳纤维复合材料的制备及光-电催化特性

本文采用电化学方法,制备了一种便于回收和分离的柔性锌镍/铝层状双羟基/碳纤维(ZnNi/Al-LDHs/CFs) 复合材料. 采用X 射线衍射、红外光谱、场发射扫描电镜、电感耦合等离子体原子发射光谱和电化学阻抗光谱技术表征了ZnNi/Al-LDHs/CFs 复合材料的结构、形貌和光电催化性能. 与单独使用Zn/Al-LDHs/CFs 作为光催化剂或Ni/Al-LDHs/CFs 作为电催化剂相比较,ZnNi/Al-LDHs/CFs 复合材料显示了良好的光-电双功能催化特性,既可被用作乙醇和甲醇氧化的电催化剂,也可光电协同催化 2,6-二氯苯酚降解.     

低温质子交换膜燃料电池自增湿膜电极研究进展

具有自增湿能力的低温质子交换膜燃料电池膜电极是实现自增湿燃料电池的重要途径,对于燃料电池的商业化具有十分重要的意义,它不仅可以大幅度减小燃料电池系统的体积,提升燃料电池系统的输出功率密度,还可以有效降低燃料电池的制造成本. 目前,低温质子交换膜燃料电池自增湿膜电极的研究主要是集中在构建具有自增湿能力的质子交换膜、自增湿催化层和复合自增湿层三个方面. 本文主要从这三个方面系统介绍近年来国内外低温质子交换膜燃料电池自增湿膜电极方面的研究进展和发展趋势.     

Experimental study and electromechanical model analysis of the nonlinear deformation behavior of IPMC actuators

This paper develops analytical electromechanical formulas to predict the mechanical deformation of ionic polymer–metal composite(IPMC) cantilever actuators under DC excitation voltages. In this research, IPMC samples with Pt and Ag electrodes were manufactured, and the large nonlinear deformation and the effect of curvature on surface electrode resistance of the IPMC samples were investigated experimentally and theoretically. A distributed electrical model was modified for calculating the distribution of voltage along the bending actuator. Then an irreversible thermodynamic model that could predict the curvature of a unit part of an IPMC actuator is combined with the electrical model so that an analytical electromechanical model is developed. The electromechanical model is then validated against the experimental results obtained from Pt-and Ag-IPMC actuators under various excitation voltages. The good agreement between the electromechanical model and the actuators shows that the analytical electromechanical model can accurately describe the large nonlinear quasi-static deflection behavior of IPMC actuators.     

Carbon nanotube-epoxy composites: The role of acid treatment in thermal and electrical conductivity

Wet acid oxidation treatment methods have been widely reported as an effective method to purify and oxidize the surface of industrial multi-walled carbon nanotubes. This work examines the use of a concentrated HNO₃/H₂SO₄ mixture in an attempt to optimize the purification procedure of industrial multi-walled carbon nanotubes with diameter distribution statistics. It is shown that acid treatments of several hours are enough to purify the nanotubes. The electrical and thermal conductivities of epoxy composites containing 0.05–0.25 wt% of an acid-treated multi-walled carbon nanotube have been studied. The electrical conductivity of the composites decreases by more than three orders, whereas the thermal conductivity of the same specimen increases very modestly as a function of the filler content.     

Preparation,characterization, and performance study of beeswax/expanded graphite composite as thermal storage material

In this study, beeswax as a new energy storage material and its composite with expanded graphite were prepared and characterized for their surface and thermal properties. Surface characterization showed no chemical interaction between beeswax and expanded graphite. The thermal conductivity of the composite was improved with 117% enhancement. The thermal performance of beeswax and its composite as a heat storage material was studied in a rectangular shell-and-tube thermal storage unit. The melting point of the composite remained almost same as that of beeswax; however, the melting time was reduced considerably, from 540 to 360 min with inlet water at 80°C and a 2-lpm flow rate.     

Effect of heat treatment on the mechanical and microstructural characterization of Mg-AZ91E/TiC composites

Mg-AZ91E/TiC_p composite was fabricated using a spontaneous infiltration technique at 950 °C under an argon atmosphere. The composites produced have 37 vol.% of metal matrix and 63 vol.% of TiC-like reinforcement. The obtained composites were subsequently solution heat-treated at 413 °C during 24 h, cold water quenched, and subsequently artificially aged at 168 and 216 °C during 16 h in an argon atmosphere. Effect of heat treatment on the microstructure and mechanical properties was evaluated. Microstructural characterization was analyzed using different techniques such as X-ray diffraction (XRD) and scanning electron microscopy (SEM). Interface between matrix and reinforcement was examined using transmission electron microscopy (TEM), and mechanical properties were evaluated by measuring the elastic modulus and hardness. Mg, TiC, Al, and Mg₁₇Al₁₂ phases through XRD were detected. Meanwhile, using TEM analysis in heat-treated composites MgAl₂O₄, MgO, and Al₂O₃ were identified. The as-fabricated composite have elastic modulus and hardness of 162 GPa and 316 Hv, respectively. After solution heat treatment and aging at 168 °C during 12 h, the composites reaches values of 178 GPa and 362 Hv for the elastic modulus and hardness, respectively. Time of aging was correlated with measures of elastic modulus and hardness.     

大气湍流对空间激光通信跟踪系统的影响

基于大气信道内的空间激光通信演示验证实验,对系统光斑跟踪精度的影响因素进行了分析,研究了大气湍流对光斑跟踪精度的影响,建立了光斑质心检测模型,设计了一套信标光光斑粗精复合跟踪系统.搭建了室内测试实验系统,完成了大气湍流对光斑跟踪精度影响的测量,结果表明在中弱湍流时,跟踪精度随湍流增大有近似线性关系,系统整体跟踪精度在5~15μrad之间,可较好地完成光斑跟踪功能.在野外环境开展的飞机-飞机激光通信演示实验中,对伺服系统的跟踪性能及跟踪精度进行实际测量,整体跟踪精度不大于15μrad,与室内实验测试系统基本一致.     

Photo-induced anisotropy in ZnO/PVA nanocomposites prepared by modified electrochemical method in PMA matrix

Substantial photo-induced optical anisotropy was discovered in ZnO/PVA nanocomposites under the influence of external bicolor laser illumination. Zinc oxide nanoparticles were synthesized by electrolysis of a sodium chloride aqueous medium including poly-methacrylic acid (PMA) in a cell system having a soluble zinc anode. The structural analysis of the ZnO powder samples has been carried out by X-Ray Diffractometry (XRD) and Scanning Electron Microscopy (SEM). The polyvinyl alcohol (PVA) embedded ZnO films obtained from the powder samples possess larger grain sizes than those in powder form. The films were prepared from the same polymer matrix but elaborated with two different PVA contents which are respectively 15% and 30%. The photoinduced anisotropy was identified by using two bicolor Er: glass laser beams incident at different angles. Substantial influence of the technological processes on the embedded nanoparticle sizes and related birefringence was explored. The process of laser induced anisotropy shows an occurrence of birefringence saturation.     

民机复合材料结构冲击后压缩设计值的确定方法

冲击后压缩设计许用值是复合材料飞机结构设计的一个非常重要的参数。本文通过分析常用的目视检测方法和飞机结构冲击能量统计结果,从凹坑深度和冲击能量截止值两方面定义了目视勉强可见损伤;根据民机设计兼顾安全性和经济性的特点,作者提出压缩设计许用值中的目视勉强可见损伤应综合考虑,慎重确定。文章还研究了复合材料层压板的抗冲击性能,从工程应用角度给出了结构冲击后压缩设计许用值的确定要点,即用小试样的冲击后压缩试验结果推导的基准系数和环境系数,对元件乃至典型结构件的冲击后压缩试验结果进行修正。