射流式单重态氧发生器研究

单重态氧O2 (a1Δg)是迄今唯一能用纯化学反应高效产生的具有长寿命的亚稳激发态分子 .为了考察提出的用两个O2 (1Δ)能量汇集反应生成氧第二单重激发态O2 (b1Σ+ g)以实现近可见短波长化学激光方案的现实性 ,设计和实验了一个氯流量为 3～ 10mmol/s的射流式单重态氧发生器 (JSOG) .考察了三种具有不同孔径和孔数目的喷头、氯气流量和脱水冷阱温度等对JSOG出口的O2 (1Δ)浓度、O2 (1Δ)分压、氯利用率及水蒸气含量的影响 .发现用聚氯乙烯管作冷阱时 ,最佳冷阱介质温度为 - 140～ - 15 0℃ ,对此提出了O2 (1Δ)表面脱活与脱水互相竞争的解释 .在最佳条件下 ,可将O2 (1Δ)气中水分压降低至 4Pa ,这一结果是首次报导     

用模拟万用表测电容

介绍了用模拟万用表和秒表测量电容的简单方法，对测量结果的误差原因进行了分析，给出了提高测量精度的几点措施。     

Assessing the Error Probability of the Model Selection Test

The asymptotic error probability of Linhart's model selection test isevaluated, and compared with the nominal significance level. We examine thecase where the expected discrepancies of the candidate models from the truemodel are asymptotically equal. The local alternatives method is employed inthe limiting operation of the asymptotic evaluation. Although the errorprobability under the null hypothesis is actually shown to be equal to orless than the level for most situations, intolerable violations of the errorcontrol are observed for nested models: It is often erroneously concludedthat the smaller model is significantly better than the larger model. Toprevent this violation, a modification of Linhart's test statistic isproposed. The effectiveness of the proposed test is confirmed throughtheoretical analysis and numerical simulations.     

On parabolic equations with a small parameter

A singularly perturbed parabolic equation with a nonlinear right-hand side of a special form is examined. A numerical analytical study of such equations is performed.     

Low-Temperature Magnetic Properties of Co Antidot Array

Cobalt antidot arrays with different thicknesses are fabricated by rf magnetron sputtering onto porous alumina substrates. Scanning electron microscopy and grazing incidence x-ray diffraction are employed to characterize the morphology and crystal structure of the antidot array, respectively. The temperature dependence of magnetic properties shows that in the temperature range 5K--300K, coercivity and squareness increase firstly, reach their maximum values, then decrease. The anomalous temperature dependences of coercivity and squareness are discussed by considering the pinning effect of the antidot and the magnetocrystalline anisotropy.     

一类常微分方程组的紧支撑样条小波方法探讨

应用三次紧支撑样条小波插值函数得到了求一类常微分方程组数值解的隐式公式,并求得到其局部截断误差为O(-h5).在此基础上给出1个显式校正求解公式,并讨论得到其局部截断误差为O(-h4).     

Magnetic anisotropy and anisotropic ballistic conductance of thin magnetic wires

The magnetocrystalline anisotropy of thin magnetic wires of iron and cobalt is quite different from the bulk phases. The spin moment of monatomic Fe wire may be as high as 3.4 μ_B, while the orbital moment as high as 0.5 μ_B. The magnetocrystalline anisotropy energy (MAE) was calculated for wires up to 0.6 nm in diameter starting from monatomic wire and adding consecutive shells for thicker wires. I observe that Fe wires exhibit the change sign with the stress applied along the wire. It means that easy axis may change from the direction along the wire to perpendicular to the wire. We find that ballistic conductance of the wire depends on the direction of the applied magnetic field, i.e. shows anisotropic ballistic magnetoresistance. This effect occurs due to the symmetry dependence of the splitting of degenerate bands in the applied field which changes the number of bands crossing the Fermi level. We find that the ballistic conductance changes with applied stress. Even for thicker wires the ballistic conductance changes by factor 2 on moderate tensile stain in our 5×4 model wire. Thus, the ballistic conductance of magnetic wires changes in the applied field due to the magnetostriction. This effect can be observed as large anisotropic BMR in the experiment.     

Lorentz-Compton佯谬与一个双赢判决性散射实验设计

通过对“可见光区域是否存在Compton效应”的讨论而进一步深化到经典条件下“光的量子理论能否包含光的经典电磁理论”的实验验证,发现了Lorentz-Compton佯谬,并基于逆Compton散射设计了一个敏感而又可行的双赢判决性散射实验来解决此佯谬。     

On the construction of samples for testing approximate optimization methods for estimate calculation algorithms

To validate approximate optimization schemes for estimate calculation algorithms (ECAs), it is necessary to compute the optimal height, which cannot be done in a reasonable amount of time. A variety of samples are built for which the optimal height of the ECAs is known by construction.