UV protection filters by dielectric multilayer thin films on Glass BK-7 and Infrasil 301

The increasing use of Ultraviolet (UV) light in medicine, industrial environments, for cosmetic use, and even in consumer products necessitates that greater attention be paid to the potential hazards of this type of electromagnetic radiation. To avoid any adverse effects of exposure to this type of radiation, four suitable protection filters were produced to block three UV bands (UVA, UVB, and UVC). The design structure of the required dielectric multilayer filters was done by optical thin film technology using the absorbing property of UV radiation for the substrates and dielectric materials. The computer analyses of the multilayer filter formulas were prepared using Macleod Software for the production processes. The deposition technique was achieved on optical substrates (Glass BK-7 and Infrasil 301) by dielectric material combinations including Titanium dioxide (Ti₂O₃), Hafnium dioxide (HfO₂), and Lima (mixture of oxides SiO₂/Al₂O₃); deposition being achieved using an electron beam gun. The output results of the theoretical and experimental transmittance values for spectral band from 200 nm to 800 nm were discussed in four processes. To analyze the suitability for use in ‘real world’ applications, the test pieces were subjected to the durability tests (adhesion, abrasion resistance, and humidity) according to Military Standard MIL-C-675C and MIL-C-48497A.     

Electrical conductivity of chromate conversion coating on electrodeposited zinc

For certain applications of galvanized steel protected with conversion coatings it is important that the surface is electrically conductive. This is especially important with mating surfaces for electromagnetic compatibility. This paper addresses electrical conductivity of chromate conversion coatings. A cross-matrix study using different zinc plating techniques by different labs showed that the main deciding factor is the type of zinc-plating bath used rather than the subsequent chromating process. Thus, chromated zinc plate electrodeposited from cyanide baths is non-conductive while that from alkaline (non-cyanide) and acid baths is conductive, even though the plate from all the bath types is conductive before conversion coating. The results correlate well with the microscopic structure of the surfaces as observed with scanning electron microscopy (SEM) and could be further corroborated and rationalized using EDX and Auger spectroscopies.     

光学薄膜测量时平顶光束激励的表面热透镜理论模型

推导了调制的平顶光束激励下基于Fresnel衍射积分的表面热透镜理论，通过数值模拟，比较了平顶光束和高斯光束激励下样品内部温度场、表面形变场和探测光衍射信号的径向分布，分析了影响表面热透镜信号的实验参数.结果表明，在最佳探测位置，平顶光束激励下的表面热透镜系统比相同情况下高斯光束激励下的灵敏度高，最高时约2倍，更有利于薄膜吸收测量. 关键词： 表面热透镜 光学薄膜 平顶光束     

Coupled lubrication and Stokes flow finite elements

A method is developed for performing a local reduction of the governing physics for fluid problems with domains that contain a combination of narrow and non‐narrow regions, and the computational accuracy and performance of the method are measured. In the narrow regions of the domain, where the fluid is assumed to have no inertia and the domain height and curvature are assumed small, lubrication, or Reynolds, theory is used locally to reduce the two‐dimensional Navier–Stokes equations to the one‐dimensional Reynolds equation while retaining a high degree of accuracy in the overall solution. The Reynolds equation is coupled to the governing momentum and mass equations of the non‐narrow region with boundary conditions on the mass and momentum flux. The localized reduction technique, termed ‘stitching,’ is demonstrated on Stokes flow for various geometries of the hydrodynamic journal bearing—a non‐trivial test problem for which a known analytical solution is available. The computational advantage of the coupled Stokes–Reynolds method is illustrated on an industrially applicable fully‐flooded deformable‐roll coating example. The examples in this paper are limited to two‐dimensional Stokes flow, but extension to three‐dimensional and Navier–Stokes flow is possible. Copyright © 2003 John Wiley & Sons, Ltd.     

等厚双层涂层材料受集中力作用的平面问题理论解

界面应力的正确评价是分析薄膜涂层材料力学特性的难题之一。利用镜像点法和Dirichlet等值性原理，本文推导了等厚双层薄膜涂层材料受表面集中力作用的平面问题理论解。该显式理论解是以固定在各镜像点上的局部坐标系下的Goursat应力函数的形式给出的。对应于高阶镜像点的应力函数，可通过递推的方法，从对应于低阶镜像点的应力函数求得，而且也易于计算机编程。随着镜像点阶数的增大，它与界面的距离也越来越大，因而相对应的应力函数对界面应力的影响越来越小。最后的算例表明，只需考虑前面有限个镜像点，便可获得足够精度的解。该理论解可作为格林函数，以求解复杂问题的理论解，也可用作边界元法的基本解，提高数值计算的精度和效率。     

氘代聚合物膜靶制备技术与性能研究

 氘代聚合物膜是快点火基础物理实验的一种重要靶型。通过氘代苯乙烯单体的本体自由基聚合反应制备氘代聚苯乙烯，并利用流延法和浇铸法制备出厚度从几十nm到数百μm的膜靶。溶剂挥发过程中的随机扰动对膜厚均匀性造成影响，采用清洁的基片和在涂沫基片或模具外加防护罩可以降低这种影响。采用PVA作脱膜剂有利于获得较薄的聚合物薄膜。DSC分析表明薄膜的玻璃化转变温度与热处理过程有关，缓慢退火有利于提高Ｔ-g和储能模量。     

SURFACE METALLIZATION OF CENOSPHERES AND PRECIPITATORS BY ELECTROLESS PLATING

This paper reports the use of a colloidal Pd^0 catalysis system to metallize the surface of precipitators separated from coal fly-ash, and metals such as Cu, Ni etc. are deposited on the precipitators surface. Alternatively, according to the characteristic surface of cenospheres, an Ag coating catalysis system is adopted to first deposit Ag on the cenospheres surface, followed, if necessary, by the deposition of other metals such as Cu, Ni, etc. on the Ag coating to produce monolayer and multilayer metal-coated cenospheres. The surface characteristics and the morphologies of the metal coatings are examined in detail with scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and X-ray photoelectron spectroscopy (XPS) techniques. It can be shown that the quality of metal coatings derived from the Aa coatina catalysis system, is better than that of the colloidal Pd^0 catalysis system.     

热喷涂技术的现状和发展

介绍了热喷涂工艺的特点，喷涂方法的种类及其技术以及热喷涂技术的应用概况，并对热喷涂技术的发展方向给予了展望。     

HL—1装置SiC涂层辐照实验的表面分析

本文应用表面分析技术研究HL-1装置中SiC涂层的等离子体辐照性能。结果表明,SiC材料应用于孔栏和壁涂层有利于减少杂质和提高等离子体品质。     

Cationic poly(methacryl oxyethyl trimethylammonium) and its poly(ethylene glycol)‐grafted analogue as capillary coating materials in electrophoresis

Cationic polyelectrolytes were synthesized and used as semipermanent coating materials for capillaries in electrophoresis. The polyelectrolytes used were a homopolymer of poly(methacryl oxyethyl trimethylammonium chloride) (PMOTAC) and its poly(ethylene glycol) (PEG)‐grafted analogue. Two PMOTAC polyelectrolytes, with molar masses of 85,000 and 300,000 g/mol, and PEG‐grafted PMOTAC with a molar mass of 280,000 g/mol were synthesized and then characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. Attachment of the polyelectrolytes to the wall of the fused silica capillary for electrophoresis caused the electroosmotic flow (EOF) to reverse. The polyelectrolyte coatings were tested over the pH range 2–11 at different buffer ionic strengths, and the most stable and strongest anodic EOFs were obtained at acidic pH values with low ionic strength buffers. Between runs the capillary is merely rinsed for 2 or 3 min with the background electrolyte solution. With the PMOTAC coatings at pH values ≤5, the RSDs of the EOFs were less than 2.9% after 60 injections. The effects of the molar mass of the polycation and of PEGylation of PMOTAC on the interactions between the polycations and basic proteins were studied at acidic pH values. The differences in the effective electrophoretic mobilities, resolution values, and plate numbers of the proteins with the different coatings were due to the EOF, as demonstrated through calculations of reduced mobilities, relative resolution values, and relative plate numbers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2655–2663, 2007