Correction procedure for the electron microprobe analysis of porous materials

A correction method is proposed for the quantitative determination of stoichiometric ratios in porous materials by electron microprobe analysis. Analysis of this kind of material is complicated by an imperfect surface that can only be improved to some extent. The correction is based on a linear dependence (different for each element) of the analyses on a sum of weight concentrations of oxides. With this correction it is possible to use analyses affected by the imperfection of the surface with much better confidence compared to common normalisation. An example is presented for a series of ceramic superconductors Bi_2.1(SrCa)_2.9Cu₂O₈₊.     

Preparation of porous polylactide microspheres by emulsion‐solvent evaporation based on solution induced phase separation

Porous polylactide (PLA) microspheres were fabricated by an emulsion‐solvent evaporation method based on solution induced phase separation. Scanning electron microscopy (SEM) observations confirmed the porous structure of the microspheres with good connectivity. The pore size was in the range of decade micrometers. Besides large cavities as similarly existed on non‐porous microspheres, small pores were found on surfaces of the porous microspheres. The apparent density of the porous microspheres was much smaller than that of non‐porous microspheres. Fabrication conditions such as stirring rate, good solvent/non‐solvent ratio, PLA concentration and dispersant (polyvinyl alcohol, PVA) concentration had an important influence on both the particle size and size distribution and the pore size within the microspheres. A larger pore size was achieved at a slower stirring rate, lower good solvent/non‐solvent ratio or lower PLA concentration due to longer coalescence time. Copyright © 2005 John Wiley & Sons, Ltd.     

Synthesis of Highly Porous Organic/Inorganic Hybrids by Ambient Pressure Sol-Gel Processing

This paper reports the synthesis of highly porous organic/inorganic hybrids by a two-step acid-base catalyzed sol-gel process and ambient pressure drying. In the method organic and inorganic precursors are copolymerized so as to incorporate organic ligands into the solid network. The two-step acid-base catalyzed process was used to prevent phase segregation during the hydrolysis and co-condensation of organic and inorganic precursors. The organic ligands incorporated into the solid gel network modify the surface chemistry. Thus, the wetting angle is significantly increased so that the collapse of the gel network is greatly reduced upon the removal of pore fluid during drying. Organic/inorganic hybrids with BET surface areas above 1250 m2/g, porosities above 75% and pore sizes of 8 nm have been synthesized.     

On the mechanism of electroluminescence emission by porous silicon layers

The analytical treatment of a model considering the electrooxidation of p-porous silicon layers under galvanostatic conditions is able to give account of experimental facts such as the shape and location of the electroluminescence peak as well as of the spectral shift of the electroluminescence peak produced by oxidation. The proposed model considers electroluminescence to be the result of electron injection into the conduction band by an adsorbed intermediate produced by electrooxidation of the surface coverage with hydrogen or siloxene of the silicon nanocrystallites. The access of holes to the surface is made possible by low accumulation layer conditions and is the rate determining step in the electroluminescence mechanism. In this way it is possible to give a satisfactory explanation to the shift towards the blue experimented by the electroluminiscence emission maximum as a consequence of electrooxidation.     

Preparation and Characterization of Nanotitanium Dioxide Coating Film Doped with Fe^3＋ Ions on Porous Ceramic

The nanotitanium dioxide （TiO2） photocatalytic and porous ceramic filtering technique is one of the advanced methods to effectively treat organic wastewater. The TiO2 sol doped with Fe^3＋ ions was prepared by sol-gel processing. The influences of the process conditions of coating nanophotocatalytic material- Fe^3＋-TiO2 film on the surface of porous ceramic filter by dipping-lift method on the performance of porous ceramic filter were studied. The porous ceramic filters have two functions at the same time, filtration and photocatalytic degradation. The results of this study showed that the pH and viscosity of the sol, amount of Fe^3＋ ions doped as well as the coating times greatly affect the quality of coating film, the performance parameters and the photocatalytic activity of the porous ceramic filter. When the pH of the sol is 3-4, the viscosity is about 6 mPa.S, the amount of doped Fe^3＋ ions is about 2.0 g/L, the porous ceramic filter has been shown to have the best filtering performance and photocatalytic activity. In this condition, the porosity of porous ceramic is about 42.5%, the pore diameter is 8-10μm. The degradation of methyl-orange is 74.76% under lighting for 120 rain.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

Growth of silicon thin film by LPE on porous silicon bilayers

The fabrication of solar cells based on the transfer of a thin silicon film on a foreign substrate is an attractive way to realise cheap and efficient photovoltaic devices. The aim of this work is to realise a thin mono-crystalline silicon film on a double porous silicon layer in order to detach and transfer it on mullite. The first step is the fabrication of a double porous silicon layer by electrochemical anodisation using two different current densities. The low current leads to a low porosity layer and during annealing, the recrystallisation of this layer allows epitaxial growth. The second current leads to a high porosity which permits the transfer on to a low cost substrate. Liquid Phase Epitaxy (LPE) performed with indium (or In+Ga) in the temperature range of 950–1050°C leads to almost homogeneous layers. Growth rate is about 0.35 μm min⁻¹. Crystallinity of the grown epilayer is similar on porous silicon and on single crystal silicon. In this paper, we focus on the realisation of porous silicon sacrificial layer and subsequent LPE growth. This revised version was published online in July 2006 with corrections to the Cover Date.     

Computer Simulation of the Structure of Porous Electrodes with an Immobilized Enzyme and Nanosized Support Particles

The efficiency of the operation of a porous electrode with an immobilized enzyme is defined, in particular, by a lucky structure of its active layer, which can contain nanosized particles of the support. The composites of such a kind are prepared with the aid of methods of colloidal chemistry. The aim of this particular investigation is to perform a computer simulation of processes of coagulation of particles of the support and their possible heterocoagulation with molecules of the enzyme. Algorithms of the formation of nanocomposite structures in solution are suggested. Calculations show that the concentration of the enzyme molecules in the nanocomposite structures cannot exceed a certain critical value. On the other hand, at a fixed value of the concentration of the enzyme molecules, the concentration of the support particles must not fall below a certain threshold quantity, which provides for the passing of current through the active layer. In order for all the enzyme molecules, rather than for a fraction of these, in the composite to take part in the process of bioelectrocatalysis, the concentration of support particles must be increased even higher, to an optimum value.__________Translated from Elektrokhimiya, Vol. 41, No. 6, 2005, pp. 738–747.Original Russian Text Copyright © 2005 by Chirkov, Rostokin.     

多孔二氧化硅中Gd3+ → Eu3+的能量传递

通过水热反应法，获得了单掺和双掺Eu³⁺，Gd³⁺的多孔二氧化硅组装体，研究了掺杂体系的光谱特性，观察到Gd³⁺ → Eu³⁺的能量传递。分析了能量传递过程，探讨了在多孔二氧化硅中Gd³⁺→Eu³⁺的能量传递的机理，其机理主要为电偶极-电偶极相互作用。