Segregation of Sn in the binary CuSn and ternary CuSnSb alloy systems

Progression studies have been followed from Cu(111)‐ and Cu(100)Sn binaries to Cu(111)‐ and Cu(100)SnSb ternary‐alloy systems under the same experimental conditions. The segregation behaviour of Sn in the two orientations are explained. It is found that the kinetic segregation profiles of Sn in the ternary alloys shift to lower temperatures as compared to that in the binary. The Sn profile shift is mainly due to the decrease in the activation energy of Sn in the ternary systems. For a particular Cu orientation, the other segregation parameters that the Sn profiles depend on, like the pre‐exponential factor, segregation energy and the interaction coefficient, are found to be the same in the two systems. There is also a change in the equilibrium segregation profiles of Sn. In the ternary system, site competition between Sn and Sb causes the Sn to suffer exponential desegregation and eventual displacement from the surface. Copyright © 2006 John Wiley & Sons, Ltd.     

Thermal and Microstructural Analysis of the Y–Ba–Cu–O/Ag Equilibrium Around the Critical Composition YBa2Cu3Ox/Ag 35 mass%

We studied the Y–Ba–Cu–O/Ag equilibrium diagram in oxygen atmosphere around the composition YBa₂Cu₃O_x/Ag35 mass%. We found a high thermal effect: the peritectic decomposition temperature of Y-123 phase is lowered from 1040 to 940°C. We demonstrate here that the nature of the phenomenon is not chemical. We explained it as the result of a mechanical segregation of Y-123 decomposition products from Y-123 phase, performed by silver. This revised version was published online in July 2006 with corrections to the Cover Date.     

Observation of defect clustering in Gd-doped calcium fluoride

Abstract

Solid solutions Ca_1-xGd_xF_2+x for 3 × 10^?7≤ x ≤10^?1 have been studied by electron paramagnetic resonance (EPR) and ionic thermal currents (ITC). The EPR experiments show the presence of two single-ion sites a cubic and a tetragonal Gd³⁺ center which co-exist with comparable abundances for intermediate impurity concentrations. The cubic center predominates at very low and high concentrations. Seven different relaxation processes have been identified from the ITC spectra and the variation of their intensity vs. x was measured. The absolute concentrations of the cubic and nn Gd³⁺ dipoles were calculated. The scavenging of interstitial fluorines by the neutral clusters explains both the abundance of cubic sites at high concentration and the variety of orientable clusters detected by ITC.     

Material profile influences in bulk‐heterojunctions

The morphology in mixed bulk‐heterojunction films are compared using three different quantitative measurement techniques. We compare the vertical composition changes using high‐angle annular dark‐field scanning transmission electron microscopy with electron tomography and neutron and x‐ray reflectometry. The three measurement techniques yield qualitatively comparable vertical concentration measurements. The presence of a metal cathode during thermal annealing is observed to alter the fullerene concentration throughout the thickness of the film for all measurements. However, the absolute vertical concentration of fullerene is quantitatively different for the three measurements. The origin of the quantitative measurement differences is discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 1291–1300     

An Investigation into the Migration of Segments in Crosslinked Fluorinated Polyimide Adhesive

Crosslinked fluorinated polyimides (CFPI) were successfully synthesized to study and explore the effect of cross-linkage on the migration of fluorinated segments and on the adhesion strength. Characterization by dynamic thermomechanical analysis (DMA) and thermo gravimetric analysis (TGA) confirmed good thermal properties of CFPI. X-ray photoelectron spectroscopy (XPS) results showed that the ratio of fluorinated component (6FDA-ODA) concentration of the surface to the bulk decreased with the crosslink density. The water contact angle of CFPI was lower than that of non-crosslinked fluorinated polyimide, indicating that the migration of fluorinated groups to the surface was reduced by the presence of cross-linkage. Therefore, CFPI, with no fluorine segregation on the surface, exhibited excellent wetting of adherent surfaces and adhesion strength, which was proved by lap shear strength (LSS) measurements and scanning electron microscopy.     

Continuous segregation of binary heterogeneous solids in a fast-fluidized bed

Continuous segregation of binary heterogeneous solids (different density mixtures) is carried out in a gas–solid fluidized bed to study the effects of gas velocity, solids feed rate, feed composition and density difference of solids on the separation factor (recovery of flotsam at top outlet) and the quality of the product (purity of flotsam at top outlet) in a continuous fast-fluidized bed. The holdup of the bed material is obtained in each experimental run. It is observed that the separation factor decreases with increase in solids feed rate or density difference of solids, and increases with gas velocity or proportion of flotsam in the feed. The quality of the product decreases with increase in gas velocity or solids flow rate, and increases with feed composition or density difference of solids. The experimental results show that the separation factor and the quality of the product are more sensitive to gas velocity than to other operating parameters. Empirical correlations for predicting the separation factor and quality of the product are proposed based on the Richards model for individual flotsam mass fraction in the feed, and the predictions agree satisfactorily with the present experimental data.     

Directional Self‐Assembly of Fluorinated Star Block Polymer Thin Films Using Mixed Solvent Vapor Annealing

We demonstrate the directional alignment of perpendicular‐lamellae domains in fluorinated three‐armed star block polymer (BP) thin films using solvent vapor annealing with shear stress. The control of orientation and alignment was accomplished without any substrate surface modification. Additionally, three‐armed star poly(methyl methacrylate‐block‐styrene) [PMMA‐PS] and poly(octafluoropentyl methacrylate‐block‐styrene) were compared to their linear analogues to examine the impact of fluorine content and star architecture on self‐assembled BP feature sizes and interdomain density profiles. X‐ray reflectometry results indicated that the star BP molecular architecture increased the effective polymer segregation strength and could possibly facilitate reduced polymer domain spacings, which are useful in next‐generation nanolithographic applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1663–1672     

Thermal evolution of the first stage Cs(THF)1.75C24 graphitide,an example of segregation and decorrelation at low temperature

The thermal variation of the first stage ternary compound Cs(THF)_1.75C₂₄ has been investigated by powder neutron diffraction. Two phase transitions have been observed. The first one occurs at 248 K and can be interpreted as a three-dimensional segregation within the graphitic host. The second one starts at about 180 K and is continuous down to 50 K. This corresponds to a decorrelation of the graphen planes at low temperature. The origin of this transition could be the elastic constraint due to the kinks of the planes.