聚氨酯泡沫塑料压缩杨氏模量的理论预测

通过微分法导出了泡沫塑料剪切模量和体积模量所满足的微分方程组，再利用联系泡沫塑料泊松比和孔隙比的Ｋｅｒｎｅｒ－Ｒｕｓｃｈ经验关系及泡沫塑料弹性常数间满足足的关系，在基体材料不可压缩的假设下，确定了泡沫塑料的杨氏模量。本文针对几种密度的泡沫塑料，分别对它们的杨氏模量进行了理论预测和实验测定，结果表明：理论预测的模量在较高密度下与实验符合的很好，在低密度下也给出相当好的近似值。此外，本文的结果同其他理     

圆钢管型钢再生混凝土短柱偏压力学性能退化研究

为研究圆钢管型钢再生混凝土短柱在偏压荷载作用下的性能退化,进行了10个短柱试件偏心受压试验。主要分析了再生粗骨料取代率、圆钢管径厚比、型钢配钢率和偏心距等参数对试件的荷载-挠度曲线、变形能力、刚度退化及耗能能力的影响。结果表明:该短柱具有较高的承载力和抗弯刚度;与普通混凝土相比,取代率的增加对短柱的承载力和变形是不利的,试件的挠度变形随着取代率的增加而增大,再生粗骨料取代率为100%的试件偏压承载力降低了8.98%,试件刚度退化速率随着取代率的增加而加快,耗能能力逐渐降低;试件的挠度变形随着圆钢管径厚比的增大或型钢配钢率的减小而增大;试件刚度退化速率随圆钢管壁厚、型钢配钢率的增加逐渐变慢,耗能能力增强;另外,偏心距对试件偏压性能影响较为显著,随着偏心距的增大,试件刚度退化和承载力降低更加明显。     

基于修正压力场理论的再生混凝土梁抗剪承载力计算方法研究

基于修正压力场理论分析有腹筋再生混凝土梁的剪切破坏机理,建立了更接近有腹筋再生混凝土梁实际受力的抗剪模型,并通过考虑再生骨料有效粒径和受箍筋作用下的裂缝宽度与构件裂缝处应力的联系,分析了再生骨料咬合力对梁斜截面抗剪性能的影响,提出了再生混凝土梁极限抗剪承载力的计算方法。此外,本文将理论结果与课题组自制的6根再生混凝土梁的抗剪承载力试验结果进行了对比,理论值与试验值吻合较好,验证了本文方法的有效性,从而为设计人员提供了一种预测再生混凝土梁极限抗剪承载力的计算方法。     

Swollen-collapsed transition in random hetero-polymers

A lattice model of a hetero-polymer with random hydrophilic-hydrophobic charges interacting with the solvent is introduced, whose continuum counterpart has been proposed by Garel, Leibler and Orland [#!GLO!#]. The transfer matrix technique is used to study various constrained annealed systems which approximate at various degrees of accuracy the original quenched model. For highly hydrophobic chains an ordinary -point transition is found from a high temperature swollen phase to a low temperature compact phase. Depending on the type of constrained averages, at very low temperatures a swollen phase or a coexistence between compact and swollen phases are found. The results are carefully compared with the corresponding ones obtained in the continuum limit, and various improvements in the original calculations are discussed. Received: 10 April 1998 / Revised: 4 June 1998 / Accepted: 1st July 1998     

Two-dimensional polymer networks at a mixed boundary: Surface and wedge exponents

We provide general formulae for the configurational exponents of an arbitrary polymer network connected to the surface of an arbitrary wedge of the two-dimensional plane, where the surface is allowed to assume a general mixture of boundary conditions on either side of the wedge. We report on a comprehensive study of a linear chain by exact enumeration, with various attachments of the walk's ends to the surface, in wedges of angles and , with general mixed boundary conditions. Received: 20 October 1997 / Accepted: 13 May 1998     

A finite element model for the fire-performance of GRP panels including variable thermal properties

A finite element study is conducted to determine the thermal response of a widely used glass reinforced plastic panel exposed to fire. This study is performed based on a formulation developed previously by the authors and improved by including the moisture and temperature-dependent thermal properties and a newly developed time-dependent non-linear mixed boundary condition at the unexposed surface of the panel. In addition, the influence of non-zero final resin mass is considered according to a recently performed thermal gravimetric analysis. In order to derive the appropriate element equations, a mixed explicit–implicit Bubnov–Galerkin finite element approach is adopted. Results of this study are presented for a standard, 10.9 mm, thickness of single-skinned polyester-based glass reinforced plastic panel and comprise temperature profiles, density distributions and moisture profiles. Comparisons are made between the predicted results and those obtained experimentally. The predicted temperatures agreed with the experimental results with an average difference of 21.41°C. A simple comparison of the present value with that of the authors’ previous model, 29.66°C, indicates a considerable improvement of 38.53% in the fire-performance prediction of the material.     

Compaction and Consolidation of Aramid and Composite Fibers. 2. Consolidation of Composite Fibers

The transverse compaction and consolidation of composite fibers obtained from blends of rigid-chain aromatic polyamides and a thermoplastic polycaproamide PA-6 are investigated with the aim to predict the fiber behavior during their compression and processing into plastics. Introduction of the aliphatic polyamide PA-6 into aramid fibers considerably increases their transverse compliance and promotes their sintering. A method for calculating the viscosity of the thermoplastic in the interfiber space from the ratio between the volumetric rate of compaction and the porosity of the material is proposed. It is found that the effective viscosity of the PA-6 melt, during its flow in the thin interfibrillar layers under compression, grows with decrease in its content in the composite fibers.     

Processes limiting the rate of response in photorefractive composites

The processes limiting the rate of response of highly diffractive, reorientationally enhanced photorefractive polymer composite materials are identified from a series of degenerate four wave mixing and Mach–Zehnder interferometric measurements. In the regime of low intensity writing beams charge generation limits the rate of holographic grating formation, but at higher intensities charge transport or reorientation of dye molecules can restrict the rate of grating formation more strongly. A grating risetime of 540 ms is observed in a composite of high dye content with high reorientational mobility of the dye molecules. In this case it is proposed that the charge carrier mobility of the doped poly(N-vinylcarbazole):2,4,7-trinitro-9-fluorenone (PVK:TNF) matrix is the principal limiting factor in grating response rates.     

Thermal Analysis of Ionizing Radiation Effects on Recycled Polyamide-6

The aim of this work is to study the ionizing radiation effects on thermal properties of there cycled polyamide-6. This polymer was irradiated with an electron beam of 1.5 MeV with different doses. The thermal properties of the samples were determined by TG, DSC and DMA measurements. It was observed that the irradiated samples of recycled polyamide-6undergo a crosslinking process. This revised version was published online in July 2006 with corrections to the Cover Date.