火花激发原子发射光谱分析不锈钢线材

火花激发原子发射光谱法应用于直径小于8mm的不锈钢线材的分析，对此类试样应用了一种特制的夹具，用块状标准样品制作工作曲线。由于线状试样和块状标准样品之间的形状差异所产生的系统不确定度借采用同类型标样作校正，对共存元素的相互干扰也采用了相应的校正方法。其它分析条件，包括严格的制样工序，氩气的纯度要求及其流量控制，以及光源的最佳条件等，作了深入的试验。按所提出的方法测定了不锈钢线材试样中碳、硅、锰、磷、硫、铬、镍及钛等8个元素。经校正后的结果与化学法测得结果相符。     

Concentrations of Active Species in the Flowing Afterglow of a Nitrogen Microwave Plasma

Measurements of nitrogen atom density, by means of NO chemical titration, along with an evaluation of the densities of some excited species N ₂ (B, v=11), N ₂ (B, v=2), N ₂ (C, v=0), and N ₂ ⁺ (B,v=0), by means of a spectroscopic study of some bands of dinitrogen, are achieved along the flowing afterglow of a dinitrogen microwave plasma (2450 MHz) for several pressures. The concentrations obtained are in the following range: [N]10 ⁺¹⁵ , [N ₂ (B, 2)]10 ⁺⁹ –10 ⁺¹⁰ , [N ₂ (B, 11)]10 ⁺⁸ –10 ⁺⁹ , [N ₂ (C, 0)]10 ⁺⁶ –10 ⁺⁷ , [N ₂ ⁺ (B,0)]10 ⁺⁶ -10 ⁺⁸ (cm^-3). From a kinetic study of the formation and decay of excited and charged species, an estimation of N ₂ (A, v), N ₂ (X, v, and N ₂ ⁺ (X) densities can be derived: [N ₂ (A, v)]10 ⁺¹² , [N ₂ (X, v6)]10 ⁺¹⁵ –10 ⁺¹⁶ , [N ₂ (X, v12)]10 ⁺¹⁴ –10 ⁺¹⁵ , [N ₂ ⁺ (X)]10 ⁺¹⁰ (cm ^-3 ).     

Formation of Negative Hydrogen Ions in a Ne–H2 Hollow Cathode Discharge

The formation of negative hydrogen ions in a conventional hollow cathode discharge has been investigated. A mixture of Ne and H₂ proved to be more advantageous compared to pure hydrogen. The study has been performed by solving the electron Boltzmann equation, coupled with a system of balance equations for neon and hydrogen neutral and charged particles. The vibrational distribution function of hydrogen has been calculated. Our calculations show unusually high population of vibrationally excited hydrogen molecules in a Ne–H₂ mixture, which explains the high density of negative hydrogen ions under optimal conditions (total gas pressure of few Torr, hydrogen number mole fraction of 1–10% and discharge current of 10–100 mA). Line intensities originating from highly excited neon states vs. hydrogen pressure have been calculated and a comparison with existing experimental results has been made.     

Investigation of glow discharge plasma for surface modification of polypropylene

Material surface properties of polymers, plastics, ceramics and textiles can be modified by atmospheric or low‐pressure glow discharge plasma. The aim of the present work is to study the surface modification of biaxially oriented polypropylene (BOPP) film in order to improve its hydrophilic and wetting properties. In this article we used low‐pressure, low‐temperature oxygen plasma for the surface treatment of BOPP. Scanning electron microscopy indicates that plasma treatment causes mainly physical changes by creating microcraters and roughness on the surface and increasing surface friction. Attenuated total reflectance infrared spectra show oxygen‐containing groups such as ? OH at 3513 cm^?1 and C?O at 1695 cm^?1. Microscopic investigations of water droplets on BOPP (treated, untreated) show that the interfacial adhesion of treated surfaces is increased. Copyright © 2003 John Wiley & Sons, Ltd.     

Kinetic model of a DC oxygen glow discharge

A simple kinetic model predicting the concentration of oxygen atoms, metastable singlet molecules O₂(a ¹) and negative ions O — in the positive column of a DC glow discharge is developed. The calculated O and O₂(a ¹) concentrations are compared to previously reported measurements for pressuresp=0.2–2 Torr and discharge currentsI=10–80 mA. The electron density calculated from the continuity equationj=n _e e v _d agrees well with experiment. The rate coefficients for electron impact processes used in the balance equations of O, O₂(a ¹), and O^– were taken from the literature as a function of the reduced electric fieldE/N forE/N=40–80 Td. A reasonable agreement is obtained between the model and the experiment with a set of 10 reactions for the production and destruction of the above-mentioned species     

甲烷二氧化碳介质阻挡放电转化产物分布研究

针对介质阻挡放电甲烷二氧化碳转化实验,分析了反应的产物分布,探讨了进料组成和反应器结构对反应的影响.反应产物包括:高H2/CO摩尔比的合成气、气态烃、高辛烷值的汽油组分、醇和酸等含氧有机物.对所述电极结构,产物的选择性随碳数增加而降低;高的甲烷进料浓度有利于烃的生成,对醇和酸的最佳甲烷进料体积分数范围在67.4％～75.1％;放电间隙越小,原料转化率和烃、酸的选择性越大,大的放电间隙对醇的生成有利.     

Temperature-dependent dry etching characteristics of III–V semiconductors in HBr- and HI-based discharges

Microwave discharges of HBr/H₂/Ar and H/H₂/Ar with additional do biasing of the sample were used to etch InP, GaAs, and AlGaAs at temperatures between 50–250°C. The etch rates increase by factors of 3–50 and 5–9, respectively, for HBr-and HI-based discharges over this temperature range, but display non-Arrhenius behavior. The etched surfaces became very rough above 100°C for InP with either discharge chemistry due to preferential loss of P, while GaAs and AlGaAs are more tolerant of the elevated temperature etching. The near-surface electrical properties of InP are severely degraded by etch temperatures above 100°C, while extensive hydrogen in-diffusion occurs in GaAs and AlGaAs under these conditions, leading to dopant passivation which can be reversed by annealing at 400°C.     

Structure and Electrochemical Behavior of Lithium-Manganese Spinels Doped with Chromium and Nickel

A series of compounds with the general formula LiMn_{2 - x - y} Cr _x Ni _y O₄, where x + y = 0.05, 0.5, or 1.0, is synthesized. It is shown that all these compounds are pure-phase spinels with parameter aequal to 0.8193-0.8236 nm. Doping a stoichiometric lithium-manganese spinel simultaneously with chromium and nickel makes the spinel structure stable. The initial specific capacity of a spinel depends on its doping degree. Doping LiMn₂O₄ with chromium and nickel simultaneously at an Mn : Cr : Ni ratio of 195 : 3 : 2 raises the spinel's specific capacity and reduces the cycling degradation. The change in the discharge capacity of LiMn_1.95Cr_0.03Ni_0.02O₄ electrodes cycled at 20, 0, and -14°C is determined.     

Preparation and characterization of functional group gradient surfaces

Functional group gradient surfaces where the density of functional groups changes gradually along the sample length were prepared. The functional group (? COOH, ? CONH₂, and ? OH group) gradient surfaces were produced by the treatment of low-density PE sheets using a corona with gradually increasing power, followed by the graft copolymerization of acrylic acid and subsequent substitution reaction of carboxylic acid groups to amide or hydroxyl groups. The prepared gradient surfaces were characterized by the measurement of water contact angle, FTIR-ATR, and ESCA. The gradient surfaces prepared can be used to systematically investigate the interactions of biological or other species in terms of the surface functional groups and their density of polymeric materials. © 1994 John Wiley & Sons, Inc.     

Polyynes and cyanopolyynes synthesis from the submerged electric arc: about the role played by the electrodes and solvents in polyynes formation

The products of the electric arc between graphite electrodes have been investigated by high performance liquid chromatography-diode-array detector (HPLC-DAD) analysis in various media: distilled water, liquid nitrogen, methanol, ethanol, n-hexane and benzene. In distilled water, hydrogen capped polyynes H-(CC)_n-H were the unique products demonstrating that carbon is supplied by the graphite electrodes while hydrogen is supplied by the solvent plasmalysis (in this case water plasmalysis). Arcing graphite electrodes in liquid nitrogen produces cyanopolyynes: NC-(CC)_n-CN demonstrating that in this case the end groups of the polyyne chains are supplied by molecular nitrogen plasmalysis caused by the electric arc. Graphite arcing in methanol and ethanol produces very clean solutions (by-products negligible or absent) of hydrogen-capped polyynes with C₈H₂ as the main product accounting for more than 70 mol percent of the total polyyne concentration. By replacing graphite electrodes with titanium electrodes in methanol or in ethanol, polyynes are not formed at all; only trace amounts of polycyclic aromatic hydrocarbons (PAHs) were detected. When arcing with graphite electrodes is conducted in n-hexane or in benzene, polyyne formation is accompanied by a significant production of PAH, especially in benzene. These results have been rationalized in terms of carbonization or coking tendency of a given solvent. The effect of using titanium electrodes in place of graphite electrodes has been investigated also in n-hexane and in benzene as well as the effects of very high electric current intensity employed to ignite and sustain the submerged electric arc.