Sulfonamides as ionophores for ion-selective electrodes. IV. New secondary sulfonamide podands and cryptands

New compounds — podands and cryptands with two secondary sulfonamide groups —have been synthesized and are described. They were tested as ionophores for guanidinium ions in PVC-membrane electrodes with bis (2-ethylhexyl)sebacate (DOS) as plasticizer.     

Aggregation effects on evaporation and the air/water interface of dodecyltrimethylammonium hydroxide solutions

 The system dodecyltrimethylammonium hydroxide (DTAOH)–water was studied by surface tension, ion-selective electrodes and evaporation in an electrobalance. Results confirmed earlier conclusions about a stepwise aggregation mechanism in DTAOH solutions. The aggregation process started at a total concentration C _T=(2.51±0.10)×10^-4 mol dm^-3) which probably corresponds to the formation of dimers. At C _T= (1.300±0.041)×10^-3 mol dm^-3 there was a change in the surface and evaporation behavior, corresponding to the formation of small, fully ionized aggregates which grew with increasing concentration. At C _T= (1.108±0.010)×10^-2 mol dm^-3 the formation of true micelles with hydroxide counterions in the Stern layer did not change significantly the evaporation and adsorption behavior. This means that between this concentration and C _T=(3.02±0.28)× M28.8n10^-2 mol dm^-3, the changes in structure were gradual. At the latter concentration there was a sudden change in the monolayer state at the air/water interface, with a strong surfactant desorption, and a major change in evaporation behavior. The changes are compatible with the formation of few, large aggregates reducing the total concentration of kinetically independent solute units, which in turn increased the activity of the solvent. This phenomenon is in agreement with literature information. The reduction in the evaporation rate of water was mainly due to the reduction of the water activity, caused by colligative effects. The reduction of the effective area available for evaporation had only a slight effect in water evaporation. Received: 9 January 1997 Accepted: 19 October 1997     

Electrochemical behaviour of Pt(100), Pt(111) and Pt polycrystalline surfaces in hydrogencarbonate solution

It was demonstrated that adsorbed CO is obtained from the reduction of NaHCO₃ solution when Pt(100), Pt(110), disordered Pt(111) and polycrystalline electrodes are employed. Reduction of CO₂ coming from the dissociation of the hydrogencarbonate anion is proposed as the reaction that produces CO. By using Fourier transform infrared spectroscopy, linear and multi-bonded CO were detected on polycrystalline platinum electrodes. The shape of the band associated with linearly adsorbed CO is monopolar as a consequence of the partial overlapping, at lower wavenumbers, of the absolute bands at both potentials (0.05 and 0.35 V).     

Comparison of pulsed amperometric detection and integrated voltammetric detection for inorganic sulfur compounds in liquid chromatography

A Variety of potential–time waveforms are useful in pulsed electrochemical detection (PED) when applied for the amperometric detection of numerous polar organic compounds following their separation by liquid chromatography (LC). Here, we compare the waveforms for pulsed amperometric detection (PAD) and integrated voltammetric detection (IVD) applied for detection of organosulfur compounds at Au electrodes in acidic media. In PAD waveforms, electrodes response is measured at a constant detection potentials. In IVD waveforms, electrodes current is integrated throughout a fast cyclic scan of the detection potential. As a consequence of this difference in detection strategy, the background signal for IVD is significantly smaller for PAD in the detection of organosulfur compounds whose response mechanisms require the concomitant formation of surface oxides on Au electrodes. Furthermore, in comparison to Pad, IVD has a larger sensitivity and a diminished system peak from 0₂ dissolved in the sample. Use of a preadsorption step increases detection sensitivity in both PAD and IVD. The limit of detection (S/N=3)for cysteine in LC-IVD is ca. 6 nM for a 50-μl injection (i.e., 300 fmol) using a detection waveform that includes a 1000-ms preadsorption period.     

Electroanalytical sensors for nonconducting media based on electrodes supported on perfluorinated ion-exchange membranes

Electroanalytical sensors, suitable for the analysis and monitoring of electroactive analytes present in gaseous phase or low-conductive liquid media, and based on electrodes in close contact with perfluorinated ion-exchange polymers are reviewed. The basic operative mechanism of these sensors, in which ion-exchange polymers act as solid polymer electrolytes (SPE's), is thoroughly discussed, while stressing the fundamental reasons why their behavior differs from that of conventional membrane electrodes. The procedures for preparing composite working electrodes by coating one side of ion-exchange membranes with stable porous films of conductive materials are described, along with the most common strategies followed to assemble this type of sensors. Useful examples of measurements in electrolyte-free media of inorganic and organic electroactive species of interest mainly for environmental analysis are given. Future prospects for the development of these sensors are also discussed.     

铂单晶电极表面不可逆反应动力学I.Pt(100)单晶电极上甲酸氧化的现场红外反射光谱研究

运用电化学暂态方法和现场时间分辨ＦＴＩＲ反射光谱研究甲酸在Ｐｔ（１００）单晶电极上的解离吸附和氧化过程,深入认识了甲酸解离吸附的反应速率在－０．２５至０．２５Ｖ电位区间呈火山形变化的规律。根据电化学现场时间分辨红外光谱的研究结果,提出在研究反动力学时避免甲酸解离吸附干扰的方法,为进一步研究甲酸在Ｐｔ（１００）电极表面经活性中间体直接氧化至ＣＯ２的反应动力学奠定了基础。     

Voltammetric Behavior of Osmium‐Labeled DNA at Mercury Meniscus‐Modified Solid Amalgam Electrodes. Detecting DNA Hybridization

The complex of osmium tetroxide with 2,2′‐bipyridine has been utilized as a probe of DNA structure and an electroactive marker of DNA in DNA hybridization sensors. It produces several voltammetric signals, the most negative of them has been observed only at mercury electrodes. This signal is of catalytic nature affording a high sensitivity of DNA determination. The catalytic current due to evolution of hydrogen in voltammetry of DNA modified by complex of osmium tetroxide with 2,2′‐bipyridine (DNA‐Os,bipy) was studied. Solid amalgam electrodes (modified with mercury menisci) of silver (m‐AgSAE), copper (m‐CuSAE), gold, and of combined bismuth and silver, were used as possible substitutes for mercury electrodes. Besides the hanging mercury drop electrode (HMDE), the catalytic current was observed only on m‐AgSAE and m‐CuSAE. Electrodes of gold and bismuth amalgams did not give the catalytic current. The detection limit of DNA‐Os,bipy on HMDE was 0.1 ng mL^?1 (RSD=2.3 %, N=11), and on m‐AgSAE 0.2 ng mL^?1 (RSD=3.1%, N=11). The m‐AgSAE was successfully applied as a detection electrode in double‐surface DNA hybridization experiments offering highly specific discrimination between complementary (target) and nonspecific DNAs, as well as determination of the length of a repetitive DNA sequence. The m‐AgSAE has proved a convenient alternative to the HMDE or carbon electrodes used for similar purposes in previous work.     

Stripping Voltammetry of Mercury(II) with a Chemically Modified Carbon Paste Electrode Containing Silica Gel Functionalized with 2,5‐Dimercapto‐1,3,4‐thiadiazole

The accumulation voltammetry of mercury(II) was investigated at a carbon paste electrode chemically modified with silica gel functionalized with 2,5‐dimercapto‐1,3,4‐thiadiazole (DTTPSG‐CPE). The repetitive cyclic voltammogram of mercury(II) solution in the potential range ?0.2 to +0.8 V (vs. Ag/AgCl), (0.02 mol L^?1 KNO₃ ; v=20 mV s^?1) show two peaks one at about 0.0 V and other at 0.31 V. However, the cathodic wave peak, around 0.0 V, is irregular and changes its form in each cycle. This peak at about 0.0 V is the reduction current for mercury(II) accumulated in the DTTPSG‐CPE. The anodic wave peak at 0.31 V is well‐defined and does not change during the cycles. The resultant material was characterized by cyclic and differential pulse anodic stripping voltammetry performed with the electrode in differents supporting electrolytes. The mercury response was evaluated with respect to pH, electrode composition, preconcentration time, mercury concentration, “cleaning” solution, possible interferences and other variables. The precision for six determinations (n=6) of 0.05 and 0.20 mg L^?1 Hg(II) was 2.8 and 2.2% (relative standard deviation), respectively. The method was satisfactory and used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

Elimination of SAS Interferences in Catalytic Adsorptive Stripping Voltammetric Determination of Cr(VI) by Means of Fumed Silica

In the work the procedure of chromium(VI) determination by catalytic adsorptive stripping voltammetry (CAdSV) with application of fumed silica, is presented. Two variants of the method are proposed: in the first fumed silica is put directly to the electrolytic cell containing tested solution, in the second the silica is shaken with the sample and next centrifuged. The effectiveness of many surface‐active substances removal from synthetic solutions as well as natural water samples, is studied. In the experiments the fumed silica (Sigma‐Aldrich) of the specific surface area in the range 200–390 m² g^?1 was used. Two types of the working electrodes were applied, i.e., hanging mercury drop electrode (HMDE) and cyclic renewable mercury film electrode (Hg(Ag)FE). In the silica presence i) the relative standard deviation (RSD) for 0.1 μg L^?1 Cr(VI) is <2% (HMDE) and <5% (Hg(Ag)FE), n=7, ii) the detection limits estimated deposition time 20 s were respectively 14 ng L^?1 (HMDE) and 22 ng L^?1 (Hg(Ag)FE). The accuracy of the method was tested by studying the recovery of Cr(VI) from spiked natural water samples.     

Electrocatalytic oxidation of hydrazine at cobalt hexacyanoferrate- modified glassy carbon, Pt and Au electrodes

The electrocatalytic oxidation of hydrazine has been studied on glassy carbon, Pt and Au electrodes modified by cobalt hexacyanoferrate (CoHCF) using cyclic voltammetry and rotating disc techniques. It has been shown that the oxidation of hydrazine to nitrogen occurs at the potential coinciding with that of Co(II) to Co(III) transformation in a CoHCF film, where no oxidation signal is observed at a bare glassy carbon electrode. A Tafel plot, derived from RDE voltammograms, exhibits a slope of 150 mV, indicating a one-electron charge transfer process to be the rate-limiting step. The electrocatalytic efficiency of the modified electrode towards hydrazine oxidation depends on solution pH, and the optimum range was found to be located between pH 5 and pH 7. The kinetic behaviour and location of the electrocatalytic process were examined using the W.J. Albery diagnosis table, and it was concluded that the reaction has either a “surface” or a “layer” reaction mechanism. Pt- and Au-CoHCF-modified electrodes show no significant electrocatalytic activity towards hydrazine oxidation. Received: 25 April 1997 / Accepted: 12 August 1997