57Fe Mössbauer spectroscopic study of (25−x)MnO–xZnO–15Fe2O3–60B2O3 glasses

The ⁵⁷Fe Mössbauer technique has been used to investigate the effect of zinc oxide substitution in (25???x)MnO–xZnO–15Fe₂O₃–60B₂O₃ glass system (x?=?0, 5, 10, 15 and 20 mol% of ZnO ). Mössbauer absorption spectra for all the samples recorded at room temperature suggest the existence of the two paramagnetic quadrupole doublets. The observed variations in hyperfine parameters have been explained on the basis of cations distribution and exchange interaction at the lattice sites and it is concluded that B–B interaction increases while the metal–metal interaction decreases due to replacement of manganese oxide by zinc oxide. These results suggest that the present glass system exhibits a paramagnetic behaviour that changes towards the weak paramagnetic when manganese oxide was replaced with zinc oxide.     

Fabrication and characterization of sputtered titanium dioxide films

TiO₂ thin films were prepared under various conditions by using a reactive RF sputtering technique. The structural, optical and electrical characteristics of the films have been investigated. All as-deposited films were amorphous. After annealing at T > 673 K, the crystallinity of the observed tetragonal anatase phase appeared improved. The optical band gap, determined by using Tauc plot, has been found to amount to 3.38 ± 0.03 and 3.21 ± 0.03 eV for the direct and indirect transition, respectively. Also the complex optical constants for the wavelength range 300-2500 nm are reported. Using the two-point probe technique, the dark resistivity has been measured as a function of the film thickness, d. The resistivity, ρ, of the samples has been found to decrease markedly with increasing thickness, but only for d < 100 nm. The behaviour of ρd versus d was found to fit properly with the Fuchs and Sondheimer relation with parameters ρ_o = 4.95 × 10⁶ Ω cm and mean free path, l = 310 ± 2 nm. The log ρ versus 1/T curves show three distinct regions with values for the activation energy of 0.03 ± 0.01, 0.17 ± 0.01 and 0.50 ± 0.02 eV, respectively.     

0.18μm CMOS工艺栅极氧化膜可靠性的衬底和工艺依存性

用斜坡电压法(Voltage Ramp, V-ramp)评价了0.18μm双栅极 CMOS工艺栅极氧化膜击穿电量(Charge to Breakdown, Q_bd)和击穿电压(Voltage to Breakdown, V_bd). 研究结果表明，低压器件(1.8V)的栅极氧化膜(薄氧)p型衬底MOS电容和N型衬底电容的击穿电量值相差较小，而高压器件(3.3V)栅极氧化膜(厚氧)p衬底MOS电容和n衬底MOS电容的击穿电量值相差较大，击穿电压测试值也发现与击穿电量 关键词： 薄氧 可靠性 击穿电压 击穿电量     

Microkinetic modelling of the formation of C1 and C2 products in the Fischer-Tropsch synthesis over cobalt catalysts

The heats of adsorption of different C₁ and C₂ molecules assumed to be present during the initial steps of the Fischer-Tropsch synthesis and activation energies for elementary steps envisioned to occur in the synthesis are calculated for Co by using the unity bond index-quadratic exponential potential (UBI-QEP) method. The preexponential factors for the elementary steps are calculated from transition-state theory, and the rate constants are calculated according to the Arrhenius equation. The activation barrier for hydrogenation of CO is found to be lower compared to hydrogen assisted dissociation of CO, which has a smaller activation barrier than direct dissociation of CO. The reaction steps with high activation barriers are eliminated. Based on this elimination two sets of elementary steps for formation of C₁ and C₂ alkenes and alkanes in the Fischer-Tropsch synthesis are established: one based on hydrogen assisted CO dissociation (carbide mechanism) and one based on CO hydrogenation (CO insertion mechanism). In addition, one mechanism of producing CO₂ from the water-gas shift reaction is proposed. The resulting mechanisms are combined and used in the microkinetic model, which are fitted to experimental results at methanation conditions (T = 483 K or 493 K, p = 1.85 bar and H₂/CO = 10) over a Co/Al₂O₃ Fischer-Tropsch catalyst. A good tuning is obtained by adjusting the C-Co and H-Co binding strengths. The microkinetic modelling based on these assumptions indicates that CO is mainly converted through hydrogenation of CO and that C₂ compounds are mainly produced by insertion of CO into a metal-methyl bond. Thus, from the surface coverages and reaction rates predicted by the microkinetic modelling the mechanism can be further reduced to only include the CO insertion mechanism. Hydrogenation of CHO to CH₂O is found to be the rate determining initiation step, and insertion of CO into a metal-methyl bond is found to be the rate determining step for chain growth. By using the UBI-QEP method for calculation of activation energies, the activation barriers for dissociation of CO and hydrogenation of surface carbon are found to be too large for the carbide mechanisms to occur. However, experimental data or another theoretical method is necessary in order to support or disprove the calculated activation energies in this work.     

The effect of ITO films thickness on the properties of flexible organic light emitting diode

Indium tin oxide (ITO) thin films were deposited on cyclic olefin copolymer substrate at room temperature by an inverse target sputtering system. The crystal structure and the surface morphology of the deposited ITO films were examined by X-ray diffraction and atomic force microscopy, separately. The electrical properties of the conductive films were explored by four-point probing. Visible spectrometer was used to measure the optical properties of ITO-coated films. The performance of the flexible organic light emitting diode device with different thickness anode was investigated in this study.     

Photo-Absorption and photochemical decomposition of copper and alkaline-earth ß-diketonates as source gases of high-Tc superconducting films

For low-temperature deposition of oxide films relating to Bi-Sr-Ca-Cu-O superconductors, photo-absorption and -decomposition properties were examined with respect to copper and alkaline-earth ß-diketonates. It was confirmed that all ß-diketonates examined were promising as source materials for photochemical vapour deposition (photo-CVD) using a low-pressure mercury lamp, in view of their large light absorption coefficients at wavelength 254 nm. The light irradiation was effective for the formation of highly crystalline oxide films at temperatures below 600 °C. By combining two sources, Ca₂CuO₃ and SrCuO₂ films were prepared. Photo-CVD of c-axis oriented Bi₂Sr₂CuO_x film was achieved by the irradiation of ternary sources of Bi(C₆H₅)₃ and strontium and copper ß-diketonates at 500 °C.     

Alloy formation in mechanically activated mixtures

The physical mixtures of hydroxocarbonates of Cu and Ni with aluminium were activated using a laboratory planetary mill. The chemical reactions and alloy formations as the effects of grinding were followed by the phase analysis of solid products based on the thermogravimetry and X-ray diffractometry. Experimental evidence indicates that the nature of reactions and products of mechanical activation was dependent on the amount of aluminium and time of grinding. This revised version was published online in July 2006 with corrections to the Cover Date.     

A Mössbauer spectroscopic study of an industrial catalyst for dehydrogenation of etylbenzene to styrene

Iron oxide catalyst with spinel structure used for dehydrogenation of ethylbenzene is one kind of important catalyst in petrochemical industry. In this work several series of industrial catalyst were prepared with different components and different manufacturing processes. Mössbauer Spectroscopy has been used to determine the optimal components and the better manufacturing process for spinel structure formation. The results may prove useful for producing the industrial dehydrogenation catalyst with better catalytic property.     

Nanocrystalline ceramic films for efficient conversion of light into electricity

Transparent nanocrystalline films of oxide semiconductors such as TiO₂ and Fe₂O₃ have been prepared on a conducting glass support employing a sol-gel procedure. The films are composed of nanometer-sized particles sintered together to allow for percolative charge carrier transport. The internal surface of these films is very high, roughness factors of the order of 1000 being readily obtained. Electric polarization was applied for forward and reverse biasing of the films and the resulting optical changes have been analyzed to derive their flat band potential. Band gap excitation of such nanocrystalline semiconductors produces electron-hole pairs which migrate through the film to be collected as electric current. Steady state photolysis and time resolved laser techniques have been applied to scrutinize the mechanism of light induced charge separation within the nanostructure. When derivatized with a suitable chromophore, TiO₂ films give extraordinary efficiencies for the conversion of incident photons into electric current, exceeding 90% for certain transition metal complexes within the wavelength range of their absorption band. The underlying physical principles of these astonishing findings will be discussed. Exploiting this discovery, we have developed a new type of photovoltaic device whose overall light to electric energy conversion yield is 10% under simulated AM 1.5 solar radiation.     

Metal–Nitrosyl complexes as a source of new vasodilators: Strategies derived from systematic chemistry and nitrosyl ligand reactivity

A series of nitrosyl complexes of empirical formula K_n[M(CN)₅NO], where M = V, Cr, Mn and Co and n = 3, or M = Mo and n = 4, have been prepared which are notional analogues of the widely used vasodilator sodium nitroprusside. Their reactivity towards common nucleophiles (OH^?, NH₂R, NHR₂, HS^? and RS^?), acid and photolysis has been investigated to elucidate the desired properties required of new metal nitrosyls which may have some potential as new non-cyanide-based vasodilators.