低温生长Cu(InGa)Se2薄膜吸收层的掺钠工艺研究

在柔性聚酰亚胺衬底上低温制备Cu(In,Ga)Se₂薄膜太阳能电池, Na的掺入会改善电池特性, 但不同的掺Na工艺对Cu(In,Ga)Se₂薄膜和器件特性的改善机理不同. 本实验通过对比前掺NaF和后掺NaF工艺发现, 在前掺Na工艺下, 由于Na始终存在于Cu(In,Ga)Se₂薄膜生长过程中, Na存在于多晶 Cu(In,Ga)Se₂ 薄膜晶界处, 起到了扩散势垒的作用, 导致晶粒细碎、加剧两相分离, 同时减小了施主缺陷的形成概率; 而在后掺Na工艺下, 掺入的Na对薄膜的结构及生长不产生影响, 仅仅起到了钝化施主缺陷、改善薄膜缺陷态的作用. 同时, 研究表明, 后掺Na工艺中, NaF必须依靠外界能量辅助才能扩散进Cu(In,Ga)Se₂内部, 实验结果证实, 只有衬底温度达到350 ℃以上时, 掺入的NaF才能较好地改善薄膜特性. 最终经掺Na工艺的优化, 得到低温工艺制备的柔性聚酰亚胺衬底器件效率达10.4%.     

聚苯乙烯芪盐L—B膜的二阶非线性光学性质研究

首次合成了一种称之为聚苯乙烯芪盐的有机高分子材料.此材料可以在水面上形成稳定的单分子层膜,并且所形成的单分子层膜可以转移到固体衬底上去.对聚苯乙烯芪盐单分子层膜进行光学二次谐波产生测量,得到聚苯乙烯芪盐对应于每个发色团的二阶非线性极化率为1.2×10~(-28)esu.制备了该材料两种不同类型的多层膜,讨论了多层膜二次谐波产生信号不随层数增加而增加的可能原因.     

非晶硅碳薄膜发光二极管发光的热致猝灭

本文详细测试了用RF-PECVD法制备的非晶硅碳薄膜发光二极管的光强电流特性和温度对器件发光强度的影响.在直流电流驱动下,器件的发光在注入电流1A/cm2左右趋于饱和,而在低占空比的脉冲电流驱动下器件的发光直至注入电流20A/cm2仍随电流近似线性增长,但提高环境温度发光随之下降.结合对器件受热情况分析表明,热致猝灭而非场致猝灭导致了器件在大电流下的发光饱和,并简要提出了改进器件散热的措施.     

反应离子镀光学薄膜的微观结构分析

用反应离子镀方法制备了ＴｉＯ２单层膜及ＴｉＯ２／ＳｉＯ２多层膜，用透射电子显微镜分别观察了由反应离子镀方法及传统蒸镀法二种不同工艺制得的ＴｉＯ２单层膜及ＴｉＯ２／ＳｉＯ２多层膜的断面结构，并对ＴｉＯ２单层膜进行了喇曼分析和卢瑟福背散射分析。     

热丝CVD生长金刚石薄膜喇曼散射研究

本文报道热丝化学气相沉积法（ＨＦＣＶＤ）生长金钢石薄膜的喇曼散射结果。选取多种峰型，对金钢石薄膜喇曼谱（１１０－１８００ｃｍ－１）采用最小二乘法进行非线性拟合，得到最佳拟合模型，其计算得到的拟合曲线怀实验谱图符合得较好。该模型揭示，石墨Ｄ峰（１３５５ｃｍ－１）是金刚石薄膜喇曼谱中不可缺少的一个组份，并且结合石墨Ｄ峰和金刚石喇曼的空间相关线型，可以解释金刚石喇曼区特殊峰形的物理机制，拟合参量的进一步     

Influence of post-deposition annealing on the structural,optical and electrical properties of Li and Mg co-doped ZnO thin films deposited by sol–gel technique

Lithium (Li) and magnesium (Mg) co-doped zinc oxide (ZnO) thin films were deposited by sol–gel method using spin coating technique. The films were deposited on glass substrates and annealed at different temperatures. The effects of annealing temperature on the structural, optical and electrical properties of the deposited films were investigated using X-ray diffraction (XRD), Ultraviolet–Visible absorption spectra (UV–VIS), photoluminescence spectra (PL), X-ray photo electron spectroscopy (XPS) and Hall measurements. XRD patterns indicated that the deposited films had a polycrystalline hexagonal wurtzite structure with preferred (0 0 0 2) orientation. All films were found to exhibit a good transparency in the visible range. Analysis of the absorption edge revealed that the optical band gap energies of the films annealed at different temperatures varies between 3.49 eV and 3.69 eV. Room temperature PL spectra of the deposited films annealed at various temperatures consist of a near band edge emission and visible emission due to the electronic defects, which are related to deep level emissions, such as oxide antisite (O_Zn), interstitial zinc (Zn_i), interstitial oxygen (O_i) and zinc vacancy (V_Zn) which are generated during annealing process. The influence of annealing temperature on the chemical state of the dopants in the film was analysed by XPS spectra. Ion beam analysis (Rutherford back scattering) experiments were performed to evaluate the content of Li and Mg in the films. Hall measurements confirmed the p-type nature of the deposited films.     

Formation of Pyrogenic Silica: Spectroscopic and Quantum Chemical Insight

This article describes the genesis of amorphous silica under high-heat conditions from SiO₂ molecules through protoparticles, primary particles, and aggregates to agglomerates using vibrational spectra and quantum chemical simulations data. The impact of small molecules (water, HCl, CO₂) is also discussed. The article also explains the nature of the pyrogenic silica amorphism.     

Study on Transient Properties of Levitated Object in Near-FieldAcoustic Levitation

A new approach to the study on the transient properties of the levitated object in near-field acoustic levitation (NFAL) is presented. In this article, the transient response characteristics, including the levitated height of an object with radius of 24 mm and thickness of 5 mm, the radial velocity and pressure difference of gas at the boundary of clearance between the levitated object and radiating surface (squeeze film), is calculated according to several velocity amplitudes of radiating surface. First, the basic equations in fluid areas on Arbitrary Lagrange-Euler (ALE) form are numerically solved by using streamline upwind
petrov galerkin (SUPG) finite elements method. Second, the formed algebraic equations and solid control equations are solved by using synchronous
alternating method to gain the transient messages of the levitated object and gas in the squeeze film. Through theoretical and numerical analyses, it
is found that there is a oscillation time in the transient process and that the response time does not simply increase with the increasing of velocity
amplitudes of radiating surface. More investigations in this paper are helpful for the understanding of the transient properties of levitated
object in NFAL, which are in favor of enhancing stabilities and responsiveness of levitated object.     

两种测试高温超导薄膜微波表面电阻方法的讨论

介绍两种工作在12GHz附近的高温超导薄膜微波表面电阻Rs测试系统,并分析各自的特点.同时简介电子科技大学在提高Rs测试精度上所作的一些改进.     

应用分离涡模型计算斜圆柱孔气膜冷却

分离涡模型(DES,Detached eddy simulation)兼有雷诺时均湍流模型计算量较小和大涡模拟计算精度高的优点。本文利用DES对平板单斜圆柱孔的气膜冷却进行了数值模拟,并将结果同RANS湍流模型的计算结果以及实验数据相比较,表明DES能有效弥补RANS湍流模型在计算三维不均匀非定常湍流场的不足,更接近实际地反映了气膜冷却中的流动和换热的本质规律。