Photocatalytic Organic Syntheses: Selective Cyclization of Amino Acids in Aqueous Suspensions

Photocatalytic reactions occurring at semiconductor particles/solution interfaces can be applied to organic syntheses. In this review article, examples of photocatalytic syntheses of cyclic amino acids by suspended semiconductor particles, e.g., titanium(IV) oxide or cadmium(II) sulfide are introduced and interpreted. Different from the photocatalytic decomposition of pollutants under aerobic conditions, selective conversion of organic compounds can be driven by the photocatalytic reactions under deaerated conditions.     

连续碳纤维增强的聚芳醚酮在Ⅰ型循环载荷下的层间破坏

用双悬臂梁(DCB)试件研究了连续碳纤维增强的聚芳醚酮复合材料(CF/PEK-C),在Ⅰ型循环载荷作用下的层间裂纹扩展行为.循环载荷采用载荷控制模式,最小载荷与最大载荷之比为0.5.在疲劳试验中,仍然发现有“阻力曲线”现象存在.层间裂纹扩展速率用指数定律与相应的应变能释放速率联系起来,并对结果进行了讨论.     

碳纳米管添加剂对质子交换膜燃料电池低铂载量膜电极性能的影响研究

以碳纳米管（CNT）作为低铂载量膜电极（CCM）催化层（0.1 mg_Pt·cm^-2）添加剂，研究了CNT的添加方式对催化层微观结构以及膜电极性能的影响.结果表明，与常规低铂载量催化层相比，在其表面喷涂一层CNT或将CNT均匀分散到Pt/C催化层中均有利于提升低铂载量膜电极的输出性能，在70℃和100%相对湿度条件下最高输出功率比常规低铂载量膜电极的0.522 W·cm^-2分别提升了22.4%和60.0%，并且均匀分散添加方式优于分层添加方式.其原因在于分层添加CNT后改善了低铂催化层和气体扩散层之间的接触界面，降低了催化层与扩散层间的接触电阻，而均匀分散添加方式除了可降低界面接触电阻外，还显著改善了低铂催化层中的气体传输，大幅提升了Pt催化剂的利用效率，使得膜电极电化学反应电阻明显降低.进一步对均匀分散添加方式中CNT的载量进行优化，表明CNT添加量为37.5 μg·cm^-2时电池输出性能最佳，70℃和100%相对湿度条件下的最大输出功率达到0.91 W·cm^-2.本研究工作表明，将CNT均匀分散添加到催化层中是一种有效提升低铂载量膜电极性能的方法.     

Study of reactive ion etching of Si and SiO2 for CFxCl4−x gases

A parametric study of the etching of Si and SiO₂ by reactive ion etching (RIE) was carried out to gain a better understanding of the etching mechanisms. The following fluorocarbons (FCs) were used in order to study the effect of the F-to-Cl atom ratio in the parent molecule to the plasma and the etching properties: CF₄, CF₃Cl, CF₂Cl₂, and CFCl₃ (FC-14, FC-13, FC-12, and FC-11 respectively). The Si etch rate uniformity across the wafer as a function of the temperature of the wafer and the Si load, the optical emission as a function of the temperature of the load, the etch rate of SiO₂ as a function of the sheath voltage, and the mass spectra for each of the FCs were measured. The temperature of the wafer and that of the surrounding Si load strongly influence the etch rate of Si, the uniformity of etching, and the optical emission of F, Cl, and CF₂. The activation energy for the etching reaction of Si during CF₄ RIE was measured. The etch rate of Si depends more strongly on the gas composition than on the sheath voltage; it seems to be dominated by ion-assisted chemical etching. The etching of photoresist shifted from chemical etching to ion-assisted chemical etching as a function of the F-to-Cl ratio and the sheath voltage. The etch rate of SiO₂ depended more strongly on the sheath voltage than on the F-to-Cl ratio.     

电感耦合等离子体原子发射光谱法测定玻璃中总硫

应用电感耦合等离子体原子发射光谱法(ICP-AES)测定了玻璃中总硫量。对测定条件,包括试样的溶解方法,分析谱线的选择,共存元素的光谱干扰及仪器的工作参数等作了系统研究。测定中选择了在紫外区的谱线(S 181.972 nm)作分析线可有效地避免了基体中大量钙的干扰。选取5件标准样品或已知样品按所提出方法各进行5次分析,算得方法的RSD值均小于1.5%,进行11次空白试验,算得方法的检出限(3S)为0.01 mg.L-1。通过对两件标准参考物质(NBS 89和GBW 03117)及一件已知样品的分析,验证了方法的准确度,所得测定结果与证书值或已知值相符。     

多支链烷基苯磺酸钠水溶液的表面性质

用自制的四种高纯度多支链烷基苯磺酸钠,研究了支链结构对其表面性质的影响.结果表明,随支链烷基碳数增加,临界胶束浓度降低,标准吸附自由能DGadӨ更负;但是,饱和吸附量Γmax却随支链烷基碳数增加而减小,且临界胶束浓度时的表面张力γcmc随吸附量减小而降低,表现出与一般表面活性剂不同的变化趋势.从多支链烷基苯磺酸钠的分子结构特点,解释了随支链烷基碳数增加Γmax和γcmc的变化规律,探讨了分子的独占面积(as)对Γmax及γcmc的影响.     

3D finite element simulation of explosive welding of three-layer plates

A 3D finite element model of the explosive welding process of three-layer plates with materials of steel-copper-copper is established. Based on the presented model, the bonding mechanism is simulated and analyzed, different detonation modes are also comparatively studied to indicate the driving force spread in few microseconds. The results show that the three layer plates bond together after many times of impact between the flyers and the base driven by detonation wave, which is damping rapidly at each impa...     

Application of a hybrid meshless technique for natural frequencies analysis in functionally graded thick hollow cylinder subjected to suddenly thermal loading

A hybrid meshless technique based on composition of meshless local Petrov–Galerkin method (for spatial variables) and Newmark finite difference method (for time domain) is developed for natural frequencies analysis of thick cylinder made of functionally graded materials (FGMs). The FG cylinder is assumed to be under suddenly thermal loading, axisymmetric and plane strain conditions. The dynamic behaviors and time history of displacements are obtained in time domain using Green–Naghdi (GN) theory of coupled thermo-elasticity (without energy dissipation). Using fast Fourier transform (FFT) technique, the displacements are transferred to frequency domain and all natural frequencies are illustrated for various grading patterns of FGMs. The variations of mechanical properties in FG thick hollow cylinder are considered to be in nonlinear volume fraction law through radial direction. The presented hybrid meshless technique furnishes a ground to analyze the effects of various grading patterns of FGMs on natural frequencies, which are obtained employing GN coupled thermo-elasticity governing equations. Also, the frequency history and natural frequencies are illustrated for various grading patterns at several points across thickness of cylinder.     

Kinematics of layered reinforced-concrete planar beam finite elements with embedded transversal cracking

In this work crack formation and development is addressed and implemented in a planar layered reinforced-concrete beam element. The crack initiation and growth is described using the strength criterion in conjunction with exact kinematics of the interlayer connection. In this way a novel embedded-discontinuity beam finite element is derived in which the tensile stresses in concrete at the crack position reaching the tensile strength will trigger a crack to open. Since the element is multi-layered, in this way the crack is allowed to propagate through the depth of the beam. The cracked layer(s) will involve discontinuity in the cross-sectional rotation equal to the crack-profile angle, as well as a discontinuity in the position vector of the layer’s reference line. A bond–slip relationship is superimposed onto this model in a kinematically consistent manner with reinforcement being treated as an additional layer of zero thickness with its own material parameters and a constitutive law implemented in the multi-layered beam element.