全氟烷基膦酸锂电解液的制备与性能研究

选取氯代二异丙基膦(C6H14PCl)为原料, 利用电化学氟化方法, 得到全氟烷基膦酸[(C3F7)2PF3], (C3F7)2PF3与氟化锂(LiF)反应得到全氟烷基膦酸锂(Li[(C3F7)2PF4]), 将其溶于碳酸乙烯酯(EC)和碳酸二甲酯(DMC)质量比为1∶1的混合溶剂中得到电解液, 考察电解液的电导率、抗水性及氧化分解电位. 以LiCoO2为正极, 锂片为负极组装两电极模拟电池体系, 测试得到电池的放电平台为3.7 V; 电池的首次放电比容量为107 mA•h•g－1; 当循环放电40次后, 容量衰减较快, 电池循环50周后, 效率仍保持102%. 交流阻抗图谱表明电解液放电时的阻抗约为140 Ω. 研究结果表明, 全氟烷基膦酸锂有望成为新型锂离子二次电池的电解质盐.     

高密度非球形和球形LiNi1/3Mn1/3Co1/3O2的合成和性能比较

利用二次干燥法和共沉淀法分别制备出了非球形的Ni_1/3Co_1/3Mn_1/3OOH前驱体和球形Ni_1/3Co_1/3Mn_1/3(OH)₂前驱体, 并分别和LiNO₃混合烧结合成高密度非球形和球形的锂离子正极材料Li(Ni_1/3Co_1/3Mn_1/3)O₂. XPS分析表明, 二次干燥法制备的非球形Ni_1/3Co_1/3Mn_1/3OOH前驱体其过渡金属Ni, Co和Mn的价态分别是＋2, ＋3和＋4, 而共沉淀法制备的球形Ni_1/3Co_1/3Mn_1/3(OH)₂前驱体其各金属价态为＋2; X射线衍射分析表明, 非球形的Ni_1/3Co_1/3Mn_1/3OOH前驱体比球形的前驱体具有较高的活性, 能够在低温下合成出Li(Ni_1/3Co_1/3Mn_1/3)O₂, 而且制备的产物结晶度高, 具有规整的层状α-NaFeO₂结构, 扫描电镜显示制备的非球形产物颗粒均匀, 颗粒间隙小, 振实密度高达2.95 g•cm^－3, 远高于球形的振实密度2.35 g•cm^－3; 充放电实验表明, 由非球形前驱体制备的Li(Ni_1/3Co_1/3Mn_1/3)O₂其充放电性能和循环性能以及体积比容量均高于球形正极材料.     

Nucleophilic additions to alkylidene bis(sulfoxides): stereoelectronic effects in vinyl sulfoxides

Conjugate additions of nucleophiles (e.g. enolates, amines and malonate anions) to bis(p-tolylsulfinyl)alkenes, alkylidene-1,3-dithiane-1,3-dioxides and alkylidene-1,3-dithiolane-1,3-dioxides have recently been published. Reasons for different selectivities and reaction rates will be discussed by consideration of steric and electronic effects. The preferred mode of attack can be explained by stereoelectronic effects (hyperconjugation) in the primarily carbanion, which is stabilized by n-->S-O-sigma* interaction with an antiperiplanar S=O group. Calculation of the transition states [BP86/aug-TZVP] for the addition of acetone enolate to the dithiane-derived alkylidene bis(sulfoxide) revealed that 6.6-7.3 kJ mol(-1) more energy is needed for an attack leading to a less-stabilized carbanion. Two axial S=O groups in dithiolane-derived alkylidene bis(sulfoxides) lead to a higher reactivity towards nucleophiles.     

A feasibility study on the use of Li(4)V(3)O(8) as a high capacity cathode material for lithium-ion batteries

Li(4)V(3)O(8) materials have been prepared by chemical lithiation by Li(2)S of spherical Li(1.1)V(3)O(8) precursor materials obtained by a spray-drying technique. The over-lithiated vanadates were characterised physically by using scanning electron microscopy (SEM) and X-ray diffraction (XRD), and electrochemically using galvanostatic charge-discharge and cyclic voltammetry measurements in both the half-cell (vs. Li metal) and full-cell (vs. graphite) systems. The Li(4)V(3)O(8) materials are stable in air for up to 5 h, with almost no capacity drop for the samples stored under air. However, prolonged exposure to air will severely change the composition of the Li(4)V(3)O(8) materials, resulting in both Li(1.1)V(3)O(8) and Li(2)CO(3). The electrochemical performance of these over-lithiated vanadates was found to be very sensitive to the conductive additive (carbon black) content in the cathode. When sufficient carbon black is added, the Li(4)V(3)O(8) cathode exhibits good cycling behaviour and excellent rate capabilities, matching those of the Li(1.1)V(3)O(8) precursor material, that is, retaining an average charge capacity of 205 mAh g(-1) at 2800 mA g(-1) (8C rate; 1C rate means full charge or discharge of a battery in one hour), when cycled in the potential range of 2.0-4.0 V versus Li metal. When applied in a non-optimised full cell system (vs. graphite), the Li(4)V(3)O(8) cathode showed promising cycling behaviour, retaining a charge capacity (Li(+) extraction) above 130 mAh g(-1) beyond 50 cycles, when cycled in the voltage range of 1.6-4.0 V, at a specific current of 117 mA g(-1) (C/3 rate).     

Critical comparison of radiometric and mass spectrometric methods for the determination of radionuclides in environmental, biological and nuclear waste samples

The radiometric methods, alpha (α)-, beta (β)-, gamma (γ)-spectrometry, and mass spectrometric methods, inductively coupled plasma mass spectrometry, accelerator mass spectrometry, thermal ionization mass spectrometry, resonance ionization mass spectrometry, secondary ion mass spectrometry, and glow discharge mass spectrometry are reviewed for the determination of radionuclides. These methods are critically compared for the determination of long-lived radionuclides important for radiation protection, decommissioning of nuclear facilities, repository of nuclear waste, tracer application in the environmental and biological researches, these radionuclides include ³H, ¹⁴C, ³⁶Cl, ⁴¹Ca, ^59,63Ni, ^89,90Sr, ⁹⁹Tc, ¹²⁹I, ^135,137Cs, ²¹⁰Pb, ^226,228Ra, ²³⁷Np, ²⁴¹Am, and isotopes of thorium, uranium and plutonium. The application of on-line methods (flow injection/sequential injection) for separation of radionuclides and automated determination of radionuclides is also discussed.     

Dynamic NMR study of the oxaphosphetane complexation with lithium during the Wittig reaction

Dynamic NMR spectroscopy at very low temperatures (148–182 K) reveal the dynamic behavior of the (2‐tri(3‐furyl)‐3‐methyl‐4‐cyclopropenyl‐oxaphosphetane) generated during a Wittig reaction between tri(3‐furyl)ethylphosphonium iodine and cyclopropylaldehyde. The possibility of formation of different adducts between Li⁺ ions and oxaphosphetane or betainic intermediates was checked calculating the formation enthalpies using the MNDO, AM1, and PM3 semiempirical MO methods. The observed species are interpreted as oxaphosphetane complexes with lithium ions present in solution. Quantum mechanical calculations confirm the spectroscopic results. © 2008 Wiley Periodicals, Inc. Int J Quantum Chem, 2008     

LiNi0.5Mn1.5O4-xFx高电压电极高温保存下的电化学行为

采用溶胶-凝胶法结合高温热处理制备了锂离子电池用5 V正极材料LiNi0.5Mn1.5O4-xFx(x=0, 0.1). 通过X射线衍射(XRD)、扫描电子显微镜(SEM)和低温氮吸附法(BET)表征了粉体材料的结构、表面形貌和比表面特性, 并以其为正极材料装配电池后, 在85 ℃下高温保存24 h, 测量了保存前后电池的一系列电化学性质变化. 结果表明, 高温保存时电池开路电压会因自放电而较快地下降. 材料的比表面积和氟掺杂显著地影响电池的电压保持能力. 比表面积愈大, 电压保持时间愈短. 氟掺杂有利于提高电池在高温条件下的电压稳定性, 并可以改善电极与电解液之间的界面性质,使充放电性能更好.     

硫化CoMo/Al2O3催化剂上H2同时催化还原SO2和NO(Ⅱ)——催化反应活性相及机理探讨

主要通过XPS表征、热力学计算以及一系列设计的评价实验等方法,对硫化CoMo/Al2O3催化剂上H2同时催化还原SO2和NO反应的活性相、吸附活性位以及反应机理进行了研究.结果表明,金属硫化物相是SO,和NO转化的主要活性相,并与载体Al2O3共同承担H2S转化为单质硫的作用.此外,反应过程中产生的品格空位也对NO转化起着重要作用.催化剂表面的阴离子空位是SO2和NO共同的吸附活性位,SO2对NO的吸附有抑制作用,而催化剂表面的L碱佗也是SO2的吸附活性位,NO可促进SO2的氧化吸附.最后,本文从反应分子的吸附与活化、NO的转化及品格硫的流失、SO2还原到H2S、H2S的转化、晶格硫的补充等5个方面提出了反应机理.     

Li3V2(PO4)3的溶胶-凝胶合成及其性能研究

以LiOH·H₂O(LiF、Li₂CO₃、LiCH₃COO·2H₂O)、NH₄VO₃、H₃PO₄和柠檬酸为原料,采用Sol-gel法合成锂离子电池正极材料Li₃V₂(PO₄)₃。优化了锂源、溶胶的pH值、预烧条件、煅烧温度等合成条件,并采用XRD、SEM、恒电流充放电及循环伏安试验等方法,研究了所合成的Li₃V₂(PO₄)₃的结构形貌和电化学性能。结果表明,以LiOH·H₂O为锂源,溶胶的pH值等于3,于氩气氢气(体积比9∶1)混合气中300 ℃预烧 4 h,并在氩气氢气(体积比9∶1)混合气中600 ℃煅烧8 h合成的Li₃V₂(PO₄)₃正极材料为标准的单斜结构,具有较高的放电比容量和较好的循环稳定性,0.1C和1C倍率下首次放电比容量分别为130 mAh·g^-1和129 mAh·g^-1;1C倍率下循环40次后,容量仍为127 mAh·g^-1,容量保持率为98.4%;随后又进行10C倍率放电,10次循环后容量为105 mAh·g^-1,容量保有率达98.1%。循环伏安测试表明,该正极材料具有较好的电化学可逆性。