Influence of Particle Morphology and Flow Conditions on the Dispersion Behavior of Fumed Silica in Silicone Polymers

The dispersion behavior of agglomerates of several grades of fumed silica in poly(dimethyl siloxane) liquids has been studied as a function of particle morphology and applied flow conditions. The effects of primary particle size and aggregate density and structure on cohesivity were probed through tensile and shear strength tests on particle compacts. These cohesivity tests indicated that the shear strength of particle compacts was two orders of magnitude higher than the tensile strength at the same overall packing density. Experiments carried out in both steady and time‐varying simple‐shear flows indicate that dispersion occurs through tensile failure. In the steady‐shear experiments,enhanced dispersion was obtained at higher levels of applied stress and, at comparable levels of applied stress, dispersion was found to proceed faster at higher shear rates. Experiments conducted in time‐varying flows further corroborated the results obtained in tensile cohesivity tests. Experiments in which the mean and maximum stresses in the time‐varying flows were matched to the stresses produced in steady shear flows highlight the influence of flow dynamics on dispersion behavior.     

沿非线性界面传输的TM波传播常数的解析解

本文得到了沿一线性介质与非线性介质界面传输的ＴＭ波精确的色散关系和传播常数的解析计算公式，导出了计算非线性介质中传输功率流的积分公式。本文方法计算传播常数及功率流的优点是可不必先知道电场分布。     

Measurements and simulations of particle dispersion in a turbulent flow

A particle imaging technique has been used to collect droplet displacement statistics in a round turbulent jet of air. Droplets are injected on the jet axis, and a laser sheet and position-sensitive photomultiplier tube are used to track their radial displacement and time-of-flight. Dispersion statistics can be computed which are Lagrangian or Eulerian in nature. The experiments have been simulated numerically using a second-order closure scheme for the jet and a stochastic simulation for the particle trajectories. Results are presented for non-vaporizing droplets of sizes from 35 to 160 μm. The simulations have underscored the importance of initial conditions and early droplet displacement history on the droplet trajectory for droplets with large inertia relative to the turbulence. Estimates of initial conditions have been made and their effect on dispersion is quantified.     

Dispersion Characteristics of Waveguide Arrays in Optical Spectrum Analyzers

Formulas for calculating the spectral characteristics of waveguide arrays, which are incorporated into waveguide spectrum analyzers based on planar waveguides, channel waveguides, and fiber optical waveguides, are derived taking into account the contribution of both the waveguide dispersion and the material dispersion to the dispersion factor. These formulas are used to study the dependence of the dispersion factor on the waveguide-system parameters for specific models of waveguide arrays. It is shown that consideration of contributions of the waveguide dispersion and material dispersion can affect profoundly the spectral characteristics of waveguide arrays.     

光双二进制传输系统的性能研究

光双二进制信号的谱宽是传统二进制信号的一半,采用双二进制传输比二进制传输色散限制的中继距离可增加一倍.本文对采用传统光接收机的光双二进制传输系统用MATLAB进行了通信仿真.结果表明:在完全消光条件下,10 Gb/s双二进制信号在常规单模光纤上传输可达160 km,40 Gb/s双二进制信号在非零色散光纤上为30 km,均比二进制增加了一倍;详细考察了消光比对传输的影响,只有消光比大于25 dB时,双二进制相对于二进制传输的优越性才呈现出来.     

Fracture strength of class II slot cavities restored with polymerizable restorative materials

This study compared the fracture strength of Class II slot cavities restored with polymerizable restorative materials. Sixty, caries-free, posterior teeth were divided into five groups of 12 teeth. The Class II slot cavities were prepared. The teeth were restored with two packable composites (Filtek P60, Surefil), a microhybrid composite (Filtek Z250)and two ormocer (Definite, Admira). The restorations were then subjected to fracture resistance tests. The marginal ridges of the restorations were loaded at an angle of 13.5° to the long axis of the tooth in an Universal Testing Machine until failure. Analysis of mean forces indicated that, Filtek P60, Surefil and Filtek Z250 exhibited better performance than Definite and Admira. The tested resin composites differed in their mechanical properties. This study suggested that fracture behavior were highly influenced by the filler system. Overall, Filtek P60, Surefil, Filtek Z250, demonstrated good fracture resistance. Copyright © 2003 John Wiley & Sons, Ltd.     

Stress Distribution in an Elastic Body with a Periodically Curved Row of Fibers

Within the framework of a piecewise homogeneous body model, with the use of exact three-dimensional equations of elasticity theory for anisotropic bodies, a method is developed for investigating the stress distribution in an infinite elastic matrix containing a periodically curved row of cophasal fibers. It is assumed that fiber materials are the same and fiber midlines lie in the same plane. The self-balanced stresses arising in the interphase in uniaxial loading the composite along the fibers are investigated. The influences of problem parameters on these stresses are analyzed. The corresponding numerical results are presented.     

Limit Regimes of Braking of Disc-Type Composite Flywheels Made by Filament Winding

A set of invariants describing the limit regimes of braking disk-type wound composite flywheels is suggested. The limit regime is determined by using a linear failure criterion. It is shown that, for generating short-time impulses of very high power, a set of small identical flywheels is more effective than one large flywheel with an equivalent mass. Particular examples illustrating the theory considered are discussed.     

Mesh-Independent Modeling and Moiré Interferometry Studies of Damage Accumulation in Open-Hole Composite Laminates

Mechanics of Composite Materials - A three-dimensional ply-level modeling of multiple matrix cracking near an open hole in a quasi-isotropic composite laminate was performed. A mesh-independent...