高功率激光驱动器中小尺度自聚焦和噪声模型

 建立了一套线性的近似分析方法，研究高功率激光驱动器中强激光传输的小尺度自聚焦效应和相位噪声对光束传输和光束质量的影响，给出了系统噪声强度、B积分值与光束近场调制对比度之间的定量关系。研究表明,为保证输出光束质量，即近场调制对比度小于给定值，系统内的噪声强度必须符合一定的谱分布。     

Hybrid free radical/cationic frontal photopolymerizations

The irradiation of hybrid photopolymer systems consisting of a free radically polymerizable multifunctional acrylate monomer and a cationically polymerizable epoxide or oxetane monomer was conducted under conditions where only the free radical polymerization takes place. This results in the formation of a free‐standing polyacrylate network film containing quiescent oxonium ions along with the unreacted cyclic ether monomer. The subsequent application of a point source of heat to the film ignites a cationic ring‐opening frontal polymerization that emanates from that site and propagates to all portions of the irradiated sample. This article examines the impact of various molecular structural and experimental parameters on these novel hybrid frontal polymerizations that produce interpenetrating network polymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4331–4340, 2007     

Reflection of Surface Plasmon Polaritons by a Corner Reflector of Negative Index Materials

A novel type of corner reflector for the reflection of surface plasmon polariton (SPP) is proposed. The reflector consists of two layers of compensatory media whose permittivity and permeability take opposite signs to that of the corresponding layer of the SP waveguide. By rigorously solving Maxwell's equations, the reflected SPP is proved to exist. The transverse wave vector of the reflected SPP is always antiparallel to that of the incident SPP and no phase retardation is introduced.     

Analysis method of the effect of fabrication errors on a planar waveguide demultiplexer

The impact of fabrication errors on a planar waveguide demultiplexer is analyzed based on an analytical method. The explicit expression of the transfer function taking into account phase and amplitude errors is presented in order to analyze the loss and crosstalk of the demultiplexer caused by fabrication errors. A basic requirement for the demultiplexer with a certain crosstalk criterion can be easily obtained. Using an etched diffraction grating demultiplexer as an example, it is shown that the analytical results have a good agreement with results from a numerical method.     

Investigation on Ochratoxin A stability using different extraction techniques

The stability of Ochratoxin A during its extraction using different extraction techniques has been evaluated. Microwave-assisted extraction and pressurised liquid extraction, in addition to two other reference methods of extraction, i.e. ultrasound-assisted and magnetic stirring-assisted extraction, were evaluated. The effect of extraction temperature using the cited techniques was checked.The results show that Ochratoxin A can be extracted using microwave-assisted extraction at temperatures up to 150 °C without degradation. Pressurised liquid extraction can be used at temperatures up to 100 °C, for extraction times of less than 30 min. Further, both ultrasound-assisted extraction and magnetic stirring extraction can be applied at temperatures up to 65 °C.High-performance liquid chromatography combined with fluorescence detection using a Chromolith RP-18e column at a flow rate of 5 mL min⁻¹ was used to quantify the Ochratoxin A. The retention time for the Ochratoxin A was 1.3 min. The limits of detection (LOD) and of quantification (LOQ) were 0.03 and 0.10 μg L⁻¹, respectively.     

四（对-羟基苯基）卟啉氧合配合物的室温固相合成，表征及氧合能力

采用固相反应合成了四羟基苯基卟啉与与Fe^2＋,Co^2＋金属离子的配合物,在室温下,将其与分子O2作用,提纯后得到两种固态氧合配合物．通过元素分析、红外光谱（IR）、核磁共振氢谱（^1HNMR）、电导、热分析（TG／DTA）、紫外光谱（UV）等测试手段确定了氧合配合物的组成为[Co·THPP·O2]（NO3）2·2H2O、[Fe·THPP·O2]Cl2·2H2O]，可知1mol配合物吸收了1molO2,采用失重法测定了氧合配合物中的配位氧,确定1mol金属配合物吸收1molO2形成超氧配合物．     

Curcumin: A naturally occurring long‐wavelength photosensitizer for diaryliodonium salts

Curcumin, a naturally occurring, intensely yellow dye extracted from the spice turmeric, is an efficient photosensitizer for diaryliodonium salt photoinitiators at wavelengths ranging from 340 to 535 nm. With curcumin as a photosensitizer, it is possible to carry out the cationic photopolymerization of a wide variety of epoxide, oxetane, and vinyl monomers with long‐wavelength UV and visible light. An example of the photopolymerization of an epoxide monomer with ambient solar irradiation is provided. Several other curcumin analogues were synthesized, and their use as photosensitizers is examined. With such photosensitizers, the range of spectral sensitivity can be extended well into the visible region of the electromagnetic spectrum. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5217–5231, 2005     

Photoinitiated curing of mono‐ and bifunctional epoxides by combination of active chain end and activated monomer cationic polymerization methods

Photoinitiated cationic polymerization of mono‐ and bifunctional epoxy monomers, namely cyclohexeneoxide (CHO), 4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexanecarboxylate (EEC), respectively by using sulphonium salts in the presence of hydroxylbutyl vinyl ether (HBVE) was studied. The real‐time FTIR spectroscopic, gel content determination, and thermal characterization studies revealed that both hydroxyl and vinyl ether functionalities of HBVE take part in the polymerization. During the polymerization, HBVE has the ability to react via both active chain end (ACE) and activated monomer mechanisms through its hydroxyl and vinyl ether functionalities, respectively. Thus, more efficient curing was observed with the addition of HBVE into EEC‐containing formulations. It was also demonstrated that HBVE is effective in facilitating the photoinduced crosslinking of monofunctional epoxy monomer, CHO in the absence of a conventional crosslinker. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4914–4920, 2007     

Glass transitions and mixed phases in block SBS

Differential scanning calorimetry (DSC) does not allow for easy determination of the glass‐transition temperature (T_g) of the polystyrene (PS) block in styrene–butadiene–styrene (SBS) block copolymers. Modulated DSC (MDSC), which deconvolutes the standard DSC signal into reversing and nonreversing signals, was used to determine the (T_g) of both the polybutadiene (PB) and PS blocks in SBS. The T_g of the PB block was sharp, at ?92 °C, but that for the PS blocks was extremely broad, from ?60 to 125 °C with a maximum at 68 °C because of blending with PB. PS blocks were found only to exist in a mixed PS–PB phase. This concurred with the results from dynamic mechanical analysis. Annealing did not allow for a segregation of the PS blocks into a pure phase, but allowed for the segregation of the mixed phase into two mixed phases, one that was PB‐rich and the other that was PS‐rich. It is concluded that three phases coexist in SBS: PB, PB‐rich, and PS‐rich phases. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 276–279, 2005