Ca(NO3)2•4H2O-catalysed Biginelli Reaction: One-pot Synthesis of 1,2,3,4-Tetrahydropyrimidin-2-ones/pyrimidine-2-thiones under Solvent-free Conditions

The synthesis of 1,2,3,4-dihydropyrimidinone/thione derivatives was achieved in good to excellent yields using calcium(II) nitrate as catalyst to promote the Biginelli three-component condensation reaction from a diversity of aromatic aldehydes, β-keto compounds and urea or thiourea. The reaction was carried out under solvent-free conditions.     

Magnetic properties of lanthanum orthoferrite fine powders prepared by different chemical routes

Fine powders of lanthanum iron oxide, LaFeO₃, have been prepared by solid state reaction as well as sol-gel synthesis and nebulized spray pyrolysis. Structures, morphologies and magnetic susceptibility measurements of these powders have been examined. The powders prepared by all the three low-temperature routes contain nearly spherical particles with an average diameter of 40 nm. These samples show a lower Neel temperature than the powder prepared by solid state reaction besides showing much lower magnetic susceptibility at low temperatures. Dedicated to Professor C N R Rao on his 70th birthday     

Measuring calcium uptake and inositol 1,4,5-trisphosphate-induced calcium release in cerebellum microsomes using Fluo-3

A simple fluorimetric method is presented for measuring calcium uptake and inositol 1,4,5-trisphosphate (InsP₃)-induced calcium release in microsomes using Fluo-3. This method is used to investigate the amplitude of calcium release (quantal release) induced by InsP₃ from rat cerebellum microsomes.     

Mössbauer study of nanodimensional nickel ferrite – mechanochemical synthesis and catalytic properties

Iron–nickel spinel oxide NiFe₂O₄ nanoparticles have been prepared by the combination of chemical precipitation and subsequent mechanical milling. For comparison, their analogue obtained by thermal synthesis is also studied. Phase composition and structural properties of iron–nickel oxides are investigated by X-ray diffraction and Mössbauer spectroscopy. Their catalytic behavior in methanol decomposition to CO and methane is tested. An influence of the preparation method on the reduction and catalytic properties of iron–nickel samples is established.     

Synthesis of biodegradable copolymers with low‐toxicity zirconium compounds. V. Multiblock and random copolymers of L‐lactide with trimethylene carbonate obtained in copolymerizations initiated with zirconium(IV) acetylacetonate

Using zirconium(IV) acetylacetonate as an initiator of lactide/trimethylene carbonate copolymerization allowed us to obtain high‐molecular‐weight copolymers with high efficiency. The reactivity ratios of the comonomers were 13.0 for lactide and 0.53 for trimethylene carbonate. Despite the large differences between the values of the reactivity ratios, copolymers with randomized chain structures were obtained. This phenomenon occurred as a result of an intensive intermolecular transesterification process proceeding along with the reaction of copolymer chain growth and modifying its final structure. Conducting the copolymerization at the relatively low temperature of about 110 °C, which minimized the influence of intermolecular transesterification, made it possible to obtain semicrystalline copolymers with multiblock structures. Increasing the temperature of copolymerization up to 180 °C was associated with strong intensification of the transesterification reactions. At this temperature, amorphous copolymers were obtained with identical compositions but highly randomized chain structures. An analysis of the chain microstructures of the obtained copolymers, determining the average length of the blocks, the intermolecular transesterification ratio, and the degree of chain randomization, was conducted by means of NMR spectroscopy. For this purpose, very specific signal assignment in the carbonyl and methylene carbon regions of the ¹³C NMR spectra to appropriate comonomer sequences of polymeric chains was performed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3184–3201, 2006     

Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

Facile syntheses of surface-functionalized micelles and shell cross-linked nanoparticles

Block copolymer micelles and shell cross-linked nanoparticles (SCKs) presenting Click-reactive functional groups on their surfaces were prepared using two separate synthetic strategies, each employing functionalized initiators for the controlled radical polymerization of acrylate and styrenic monomers to afford amphiphilic block copolymers bearing an alkynyl or azido group at the α-terminus. The first route for the synthesis of the azide-functionalized nanostructures was achieved via sequential nitroxide-mediated radical polymerization (NMP) of tert-butyl acrylate and styrene, originating from a benzylic chloride-functionalized initiator, followed by deprotection of the acrylic acids, supramolecular assembly of the block copolymer in water and conversion of the benzylic chloride to a benzylic azide. In contrast, the second strategy utilized an alkynyl-functionalized reversible addition fragmentation transfer (RAFT) agent directly for the RAFT-based sequential polymerization of tetrahydropyran acrylate and styrene, followed by selective cleavage of the tetrahydropyran esters to give the α-alkynyl-functionalized block copolymers. These Click-functionalized polymers, with the functionality located at the hydrophilic polymer termini, were then self-assembled using a mixed-micelle methodology to afford surface-functionalized “Clickable” micelles in aqueous solutions. The optimum degree of incorporation of the Click-functionalized polymers was investigated and determined to be ca. 25%, which allowed for the synthesis of well-defined surface-functionalized nanoparticles after cross-linking selectively throughout the shell layer using established amidation chemistry. Functionalization of the chain ends was shown to be an efficient process under standard Click conditions and the resulting functional groups revealed a more “solution-like” environment when compared to the functional group randomly inserted into the hydrophilic shell layer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5203–5217, 2006     

Synthesis of biodegradable copolymers with low‐toxicity zirconium compounds. IV. Copolymerization of glycolide with trimethylene carbonate and 2,2‐dimethyltrimethylene carbonate: Microstructure analysis of copolymer chains by high‐resolution nuclear magnetic resonance spectroscopy

The results of the copolymerization of glycolide with cyclic trimethylene carbonate and 2,2‐dimethyltrimethylene carbonate are described. The copolymerization was conducted in the presence of low‐toxicity zirconium(IV) acetylacetonate as an initiator. With this kind of initiator, the composition of the comonomer units in the copolymer chains was assumed to be obtained with high efficiency. Despite significant differences in the comonomer reactivity, in copolymers containing comparable amounts of glycolidyl and carbonate sequences, highly randomized chain structures were observed. This effect resulted from strong intermolecular transesterification that proceeded during the studied copolymerization and caused glycolidyl microblock randomization. The assignment of the spectral NMR lines to appropriate comonomer sequences of polymeric chains was performed in the region of methylene protons of glycolidyl units in ¹H NMR spectra of the copolymers and in the carbonyl region of carbon spectra. The equations were formulated for a detailed characterization of the obtained copolymer chains, the average lengths of the blocks, and the transesterification and randomization coefficients. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 98–114, 2006