Effects of Moisture and Stresses on the Structure and Properties of Polyester Resin

The results of a complex study of structural changes in a cured Norpol 440 polyester resin under the action of damp environment and mechanical loading are presented. A considerable effect of absorbed moisture on the structure and some characteristics of the material is revealed by using thermophysical methods and X-ray diffractometry. The joint effect of moisture and mechanical stress is estimated by investigating the creep in stationary and nonstationary moisture conditions. The anisotropy of the material structure formed during creep is evaluated from the results of dilatometric measurements. It is found that the degree of anisotropy of the material after creep accompanied by moisture sorption is higher than that after creep in the conditions of moisture equilibrium with atmosphere. It is established that the aftercure and relaxation of the residual creep deformation come to an end at heating to 80-85°C. At a further rise in temperature and repeated heating, changes in the material structure are not observed.     

Stratifiable Families of Extremals and Sufficient Conditions for Optimality in Optimal Control Problems

It is shown that, if a parametrized fämily of extremals F can be stratified in a way compatible with the flow map generated by F, then those trajectories of the family which realize the minimal values of the cost in F are indeed optimal in comparison with all trajectories which lie in the region R covered by the trajectories of F. It is not assumed that F is a field covering the state space injectively. As illustration, an optimal synthesis is constructed for a system where the flow of extremals exhibits a simple cusp singularity.     

Unusual current‐voltage characteristics of single crystalline and bicrystalline La0.7Ca0.3MnO3 films

The current‐voltage characteristics of single crystalline and bicrystalline La_0.7Ca_0.3MnO₃ films were measured and analyzed. Several epitaxial films, as well as 45° [001]‐tilt grain boundaries, display current‐voltage characteristics which are asymmetric with respect to polarity reversal of the bias current. One epitaxial film has a polarity dependent resistance of ～340kΩ and of ～670kΩ in forward and in reverse direction, respectively.     

Evaluation of closed-vessel microwave digestion method for the determination of trace impurities in polymer-based photoresist by inductively coupled plasma mass spectrometry

A closed microwave digestion method followed by inductively coupled plasma spectrometric (ICP-MS) analysis was evaluated for the determination of trace impurities in photoresist. To optimize the digestion procedure, several digestion parameters such as acid, heating temperature and heating time were evaluated. Besides, the digestion efficiency of used photoresist material and the recovery of analyte elements obtained by the use of gravimetric method and ICP-MS measurement, individually, were also compared to clarify the completeness of digestion. According to our experiments, the gravimetric method was found to be not so relevant to the completeness of digestion, because the remaining sample matrix could cause suppression effect in the subsequent ICP-MS measurement. In view of minimizing blank value and working time, a simple single-step heating program was proposed to mineralize 0.25 ml of photoresist material with 5 ml of nitric acid at 180 °C for 10 min. Based on the comparative study of the analytical results obtained by instrumental neutron activation analysis (INAA) and proposed method, the reliability of proposed method for the determination of trace metallic impurities in photoresist material has been confirmed.     

Pt(IV)-catalyzed cyclization of arene-alkyne substrates via C-H bond functionalization

We herein report that PtCl₄ has proven to be a hydroarylation catalyst with an efficiency and substrate scope superior to previously known methods. This catalyst demonstrated consistent performance with arene-yne substrates of diverse structural features, including propargyl ethers, propargylamines, and alkynoate esters, providing good to excellent yields of the 6-endo products (chromenes, dihydroquinolines, and coumarins). In contrast, Pt(II), Pd(II), and Ga(III) salts were shown to be sensitive to the substitution on the alkyne moiety. PtCl₄ is compatible with both terminal and disubstituted alkynes, as well as with various functionalities on the arene ring, including methyl, methoxyl, hydroxyl, protected amine, and halide.     

Kinetic features of ethylene polymerization over supported catalysts [2,6‐bis(imino)pyridyl iron dichloride/magnesium dichloride] with AlR3 as an activator

The effects of polymerization temperature, polymerization time, ethylene and hydrogen concentration, and effect of comonomers (hexene‐1, propylene) on the activity of supported catalyst of composition LFeCl₂/MgCl₂‐Al(i‐Bu)₃ (L = 2,6‐bis[1‐(2,6‐dimethylphenylimino)ethyl] pyridyl) and polymer characteristics (molecular weight (MW), molecular‐weight distribution (MWD), molecular structure) have been studied. Effective activation energy of ethylene polymerization over LFeCl₂/MgCl₂‐Al(i‐Bu)₃ has a value typical of supported Ziegler–Natta catalysts (11.9 kcal/mol). The polymerization reaction is of the first order with respect to monomer at the ethylene concentration >0.2 mol/L. Addition of small amounts of hydrogen (9–17%) significantly increases the activity; however, further increase in hydrogen concentration decreases the activity. The IRS and DSC analysis of PE indicates that catalyst LFeCl₂/MgCl₂‐Al(i‐Bu)₃ has a very low copolymerizing ability toward propylene and hexene‐1. MW and MWD of PE produced over these catalysts depend on the polymerization time, ethylene and hexene‐1 concentration. The activation effect of hydrogen and other kinetic features of ethylene polymerization over supported catalysts based on the Fe (II) complexes are discussed. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5057–5066, 2007     

TG and DSC study of the properties of coked molecular sieve catalyst

A cracking catalyst designatedSRNY was manufactured from a commercialSRNY molecular sieve (M.S.). The support consisted of kaolin, clay and SiO₂. The coking behaviour of theSRNY M.S., the support and the catalyst were examined with light diesel oil (LDO) as feedstock in a microreactor. The physico-chemical properties of both fresh and aged samples, subjected to or not subjected to the cracking reaction ofLDO, were sequentially characterized by means of pore structure determination and thermal analysis. The pore structure included the specific surface area and the pore volume or porosity. Thermal analysis methods used included TG and DSC. The results indicated that all coked samples exhibited obvious changes in surface pore structure and acidity in comparison with non-coked samples. Their specific surface area and acid amount decreased with increase in the coke content of the samples. The apparent activation energy data obtained from decoking samples in an air flow, using the temperature-programmed oxidation (TPO) method, showed that the kinetic parameters of theSRNY M.S. differed from those of theSRNY catalyst and its support.     

应变Si1-xGex层中p型杂质电离常温和低温特性

本文采用解析的方法计算了应变Si1-xGex层中p型杂质电离度与Ge组分x、温度T以及掺杂浓度N的关系.发现常温时,在同一Ge组分下,随着掺杂浓度的升高,杂质的电离度的先变小,而后又迅速上升到1.在同一掺杂浓度下,轻掺杂时,杂质的电离度随Ge组分的增加先变大,而后几乎不变;重掺杂时,杂质电离能变为0后,杂质电离度为1.低温下,轻掺杂时,载流子低温冻析效应较为明显,杂质的电离度普遍较小,当掺杂浓度大于Mott转换点时,载流子冻析效应不再明显,电离率迅速上升到1.在同一Ge组分下,随着掺杂浓度的升高,杂质的电离度先变小,后变大,而后又迅速上升到1.在同一掺杂浓度下,轻掺杂时,杂质的电离度随Ge组分的增加变大;重掺杂时,杂质电离能变为0后,杂质电离度为1.     

Vlasov辐射器反射特性研究

 利用矩量法导出Vlasov辐射器端口处各种模式模系数（振幅）的计算方法，并利用此方法通过数值计算研究了斜切形Vlasov辐射器的反射特性，得到了辐射器端口反射系数和斜切角度及直径波长比之间的关系。结果表明斜切形辐射器具有很小的反射系数，并从反射特性上为辐射器结构参数的选择提供了依据。     

Stability of solutions to the Cauchy problem for a plane hyperbolic system with time-periodic coefficients

Considering a plane hyperbolic system with time-periodic coefficients, we construct a version of the direct Lyapunov method with the condition on the derivative of the Lyapunov functional along the trajectories of the system which is weakened by use of periodicity of the coefficients. We exhibit an illustrative example.