Pore Sizes of Solids

A new, fast, and simple method based on size exclusion chromatography permits determination of the volumes of open and closed pores of rigid solids such as silica or porous glasses, together with the specific surface and the pore-size distribution for pore diameters ranging from 10 to 4000Å. The results are in good agreement with those obtained by classical methods (capillary condensation, mercury porosimetry).     

Polymer-silica nanocomposites prepared by sol-gel technique: Nanoindentation and tapping mode AFM studies

Polymer-silica nanocomposites based on poly(2-hydroxyethyl acrylate) (PHEA) have been prepared by the simultaneous polymerization of the organic and the silica phases in a sol-gel process with the silica precursor tetraethyl orthosilicate (TEOS). The structure of this system is investigated using atomic force microscopy (AFM) in the tapping mode and in nanoindentation experiments. The structure of the PHEA/silica hybrids strongly depends on the ratio of both components in the system. For silica weight fractions lower than 0.15, the system consists of aggregated silica particles dispersed in the organic matrix; above that concentration of silica the structure is co-continuous with that of the organic matrix, similarly to two interpenetrated networks.     

Sedimentation equilibrium of suspensions of colloidal particles at finite concentrations

Equilibrium concentration profiles of non-dilute colloidal suspensions are calculated by means of the Carnahan-Starling expression for the osmotic compressibility of hard sphere liquids. The profiles depend on the average volume fraction of the suspension, , and on the field interaction parameter, ₀ (reciprocal of the Péclet number at infinite dilution). Profiles are computed for values of and ₀ typical of those encountered in sedimentation field-flow fractionation experiments. It is found that, in most cases, the volume fraction at the depletion wall is negligibly small and that the volume fraction at the accumulation wall ₀, depends on the ratio <>₀/₀ only. An inflexion point is found in the concentration profile if ₀ is larger than 0.13 whatever the value of ₀.     

Application of pure silica gel as cation-exchange stationary phase in lon chromatography with indirect photometric detection for common mono-and divalent cations using aromatic monoamines as eluents

Summary A pure silica gel (Pia Seed 5S-60-SIL), synthesized by the hydrolysis of pure tetraethoxysilane [Si(OCH₂CH₃)₄], was applied as a cation-exchange stationary phase in ion chromatography with indirect photometric detection for common mono-and divalent cations (Li⁺, Na⁺, NH₄ ⁺, K⁺, Mg²⁺, and Ca²⁺) using various protonated aromatic monoamines (tyramine [4-(2-aminethyl) phenol], benzylamine, phenylethylamine, 2-methylpyridine and 2,6-dimethylpyridine) as eluet ions. When using 0.75 mM tyramine-0.25 mM oxalic acid-1.5 mM 18-crown-6 (1,4,7,10,13,16-hexaoxacyclooctadecane) at pH 5.0 as the eluent, excellent simultaneous separation and highly sensitive detection at 275 nm for these mono-and divalent cations were achieved on the Pia Seed 5S-60-SIL column (150×4.6 mm I.D.) in 20 min.     

一种制备单分散SiO2空心微球的新方法

在乙醇/氨水介质中, 分别以分散聚合和无皂乳液聚合方法制得的不同粒径聚苯乙烯(PS)微球为模板, 以正硅酸乙酯(TEOS)为前驱体, 通过控制介质中氨水的初始体积, 一步法制得了不同粒径的单分散SiO2空心微球. 整个过程无需添加其它溶剂溶解或高温煅烧的方法来除去模板微球. 对SiO2空心微球进行测试表征, 提出了SiO2空心微球的可能形成机制.     

The optimization of silica gel synthesis from chemical bottle waste using response surface methodology

To reduce the amount of hazardous chemical bottle waste in the environment, we report the optimization research of silica extraction in chemical bottle waste into silica gel. Alkali fusion and sol–gel process were utilised to prepare silica gel effectively. The alkali fusion process was carried out by adding sodium hydroxide to produce sodium silicate. Afterwards, silica gel was prepared by the sol–gel method using hydrochloric acid. Box-Behnken Design (BBD) was applied to Optimisation factors the poptimiseactors affecting the silica recovery. The factors that optimised mass ratio, particle size, and temperature. The optimum recovery of silica gel was obtained by SiO₂: NaOH mass ratio of 1:3, the particle size of 63–74 µm, and a temperature of 800 °C. The purity of silica gel optimum is 63.74% characterised using X-ray fluorescence. The structure of silica gel is the appearance of amorphous peaks at 2θ 20-30° characterised using an x-ray diffractogram. The silica gel surface was characterises using scanning electron microscopy-energy dispersive x-ray. It showed an irregular surface and characteristic showed that silica gel had a radius of 15.74 nm and a specific surface area of 297.08 m².     

Low‐Temperature Facile Template Synthesis of Crystalline Inorganic Composite Hollow Spheres

This report presents a facile approach for the low‐temperature synthesis of crystalline inorganic‐oxide composite hollow spheres by employing the bulk controlled synthesis of inorganic‐oxide nanocrystals with polymer spheres as templates. The sulfonated polystyrene gel layer can adsorb the target precursor and induce inorganic nanocrystals to grow on the template in situ. The crystalline phase and morphology of the composite shell is tunable. By simply adjusting the acidity of the titania sol, crystalline titania composite hollow spheres with tunable crystalline phases of anatase, rutile, or a mixture of both were achieved. The approach is general and has been extended to synthesize the representative perovskite oxide (barium and strontium titanate) composite hollow spheres. The traditional thermal treatment for crystallite transformation is not required, thus intact shells can be guaranteed. The combination of oxide properties such as high refractive index, high dielectric constant, and catalytic ability with the cavity of the hollow spheres is promising for applications such as opacifiers, photonic crystals, high‐κ‐gate dielectrics, and photocatalysis.     

Alginic acid–silica hydrogel coatings for the protection of osmotic distillation membranes against wet-out by surface-active agents

The formulation of organic–inorganic polymer composites can be used to enhance selected properties, such as susceptibility to microbial attack, thermal stability, mechanical strength and water sorption capability. Accordingly, a series of alginic acid–silica hydrogel films was prepared for testing as protective coating materials for PTFE osmotic distillation membranes. Unprotected hydrophobic membranes are subject to wet-out when contacted by surface-active agents, such as oils and detergents. Films containing 5, 10, 15 and 20 wt.% silica, with and without the addition of glycerol for plasticisation, moisturisation and silica dispersion, were characterised using scanning electron microscopy, X-ray diffraction, differential scanning calorimetry, mechanical strength measurements, and water-swelling measurements. Composites prepared with glycerol addition had better thermal stability, mechanical strength and water sorption capability than those prepared without glycerol addition. Uncoated membranes and membranes coated with composites prepared with glycerol addition were tested for OD performance and resistance to surface-active agents using pure water, orange oil (limonene)–water mixtures, and sodium dodecylbenzene sulfonate detergent solutions. Uncoated membranes showed immediate hydrophobicity loss in the presence of orange oil and detergent. For coated membranes, no wet-out occurred over the 15 h duration of three consecutive 5 h OD trials using orange oil–water mixtures. In the case of detergent solutions, the coating afforded protection to the membrane for 4–5 h. In a separate trial, no wet-out occurred when the coated side of the membrane was placed in contact with 1.2 wt.% orange oil for 72 h.     

In situ preparation of polyaniline coated fumed and precipitated silica fillers and their composites with nitrile rubber (Investigation on structure-property relationship)

In situ synthesis of polyaniline (PAni) coated pyrogenic or fumed silica (PCFS) and precipitated silica (PCPS) were carried out by the oxidative polymerization of aniline in presence of fumed silica (FS) and precipitated silica (PS). Both uncoated and PAni coated silica fillers were characterized through scanning electron microscope (SEM), infrared spectroscopy and thermo-gravimetric analysis (TGA) to evaluate particle morphology and physico-chemical character of coated and uncoated silica particles. Semi-conducting composites made from two different types of PAni coated silica fillers with NBR exhibit different trend in the variation of electrical properties under different temperature and pressure. These differences in electrical properties of two types of composites are mainly due to physico-chemical characteristics of filler particles as well as their distribution in the polymer matrix. This type of composites may be used as semi-conducting and ESD (electrostatic discharge) material.     

Adsorption from binary solvent mixtures onto silica gel by HPLC frontal analysis

Summary The chromatographic technique of frontal analysis is applied to measuring adsorption from binary liquid mixtures by silica gel. The complete adsorption isotherm of a solvent mixture is obtained by measuring the break-through curves for a series of small concentration steps of the mobile phase. This method offers a direct way to determine the composition of the stationary phase in liquid-solid chromatography with mixed mobile phases. The surface excess isotherms of all binary systems formed by benzene, cyclohexane, and 1,2-dichloroethane, at the solution-silica gel interface at 25 °C are presented. The data of the three systems are shown to be thermodynamically mutually consistent.