氨基官能化聚乳酸电纺纤维的制备、 表征和应用

通过聚乳酸(PLA)和氨基丙基三乙氧基硅烷(KH550)混合进行静电纺丝制备氨基官能化聚乳酸纳米纤维. 采用滴定法测定了纤维表面氨基含量, 证明当KH550的添加量为3%~13%(质量分数)时, 有19%~26%的氨基出现在纤维的表面. 利用场发射扫描电子显微镜、 差示扫描量热(DSC)仪、 接触角测试仪和电子拉伸机对纤维形貌、 PLA的玻璃化转变温度和熔点以及纤维膜的亲水性和力学性能进行了表征. 结果表明, KH550的加入可以在电纺纤维表面引入氨基, 同时使纤维直径变细, 使PLA的玻璃化转变温度上升, 熔点下降, 电纺纤维膜的亲水性略有增加, 力学性能有所下降. 通过吸附将金纳米粒子负载到氨基官能化聚乳酸电纺纤维膜上, 得到负载型催化剂, 对硼氢化钠还原对硝基苯酚的反应具有良好的催化活性和重复使用性.     

含蜜胺基团的新型苝酰亚胺染料的合成及纳米纤维的构筑

合成了一种含三嗪基团的新型苝酰亚胺染料(T-PTCD), 并对其分子结构进行了确认. 考察了溶剂的极性和溶剂体积比等因素对相转移法和快速溶剂扩散法制备的T-PTCD聚集体形貌结构的影响. 结果表明, 以甲醇和三氯甲烷分别作为"不良"溶剂和"良"溶剂, 低体积比甲醇/氯仿在一定程度上有利纳米纤维的形成; 当体积比为1:4时, 采用相转移法可制备出直径大约100 nm左右, 长度为几十微米的结构规整的纳米纤维.     

High flux nanofiltration membranes based on interfacially polymerized polyamide barrier layer on polyacrylonitrile nanofibrous scaffolds

Electrospun polyacrylonitrile (PAN) nanofibrous scaffold was used as a mid-layer support in a new kind of high flux thin film nanofibrous composite (TFNC) membranes for nanofiltration (NF) applications. The top barrier layer was produced by interfacial polymerization of polyamides containing different ratios of piperazine and bipiperidine. The filtration performance (i.e., permeate flux and rejection) of TFNC membranes based on electrospun PAN nanofibrous scaffold was compared with those of conventional thin film composite (TFC) membranes consisting of (1) a commercial PAN ultrafiltration (UF) support with the same barrier layer coating and (2) two kinds of commercial NF membranes (i.e., NF90 and NF270 from Dow Filmtec). The nanofiltration test was carried out by using a divalent salt solution (MgSO₄, 2000 ppm) and a cross-flow filtration cell. The results indicated that TFNC membranes exhibited over 2.4 times more permeate flux than TFC membranes with the same chemical compositions, while maintaining the same rejection rate (ca. 98%). In addition, the permeate flux of hand-cast TFNC membranes was about 38% higher than commercial NF270 membrane with the similar rejection rate.     

不同磺酸掺杂聚苯胺的制备及在超级电容器中的应用

以MnO₂为氧化剂,采用乳液聚合法,用三种不同的磺酸型表面活性剂制备掺杂聚苯胺(PANI)。通过扫描电子显微镜(SEM)、傅里叶变换红外(FTIR)光谱以及X射线衍射(XRD)等手段对其结构及形貌进行表征;用所得的掺杂聚苯胺制作电极,组装成对称扣式超级电容器,用循环伏安法(CV)、电化学阻抗(EIS)和恒电流充放电技术进行电化学性能研究。结果表明,磺酸表面活性剂的引入有利于PANI纳米纤维的形成和分散,掺杂Nafion的PANI纤维直径在30-40 nm之间,纤维交织成多孔的疏松结构;当放电电流为0.1 A·g^-1时,以PANI-Nafion、PANI-SDS(十二烷基磺酸钠)、PANI-SDBS(十二烷基苯磺酸钠)为电极材料的超级电容器比容量分别为385.3、359.7、401.6 F·g^-1,均高于未掺杂PANI的比容量(235.8 F·g^-1);其中, PANINafion的循环稳定性最好, 1000次循环后其比容量保持率高达70.7%。     

静电纺丝纳米ZrO_2:Ti纤维的制备与发光性质的研究

通过静电纺丝和高温煅烧相结合的方法制备了一维钛掺杂氧化锆的纳米纤维。复合纤维在1 000℃煅烧后,由于模板剂、聚乙烯吡咯烷酮(PVP)在高温下的分解,纤维直径大大减小,扫描电镜观察最终得到直径100 nm左右的单斜相纤维。利用稳态光谱和时间分辨光谱技术室温下研究了纤维的光致发光性质。结果表明发射主峰在467 nm的宽带,在350 nm处有一个小肩峰。两种不同的发光行为可以通过ZrO2∶Ti纳米纤维中存在的两种情况的氧空穴作为电子俘获中心来解释。一种由电荷补偿产生的氧空位,俘获电子,产生467 nm处Ti参与的发光现象。另外一种ZrO2表面缺陷导致的氧空穴,对应于350 nm的发光现象,没有发现长余辉现象。测得的激发态寿命短于体材料而长于普通的纳米晶,可能是由于一维纳米结构的独特性质导致的。     

γ射线辐射下制备聚苯胺/银纳米复合材料及其输运性质

在γ射线辐射下,采用一步法制备了聚苯胺/银复合材料,通过红外光谱、紫外-可见光光谱、X射线衍射分析表明,所制备的样品由聚苯胺和面心立方相的银组成. 反应机理研究表明,聚苯胺是通过苯胺阳离子与·OH反应生成的苯胺阳离子自由基之间的反应生成的,银是通过银Ag⁺与e^-_aq的反应生成的. 扫描电子显微镜和透射电子显微镜显示聚苯胺/银复合物呈纳米纤维和纳米颗粒的形貌,这种形貌可能是由于类似〝快速混合〞聚合反应的过程造成的. 在80～300 K,聚苯胺/银复合材料的输运行为可较好地符合变程跃迁模型,而在80 K以下,则明显地偏离变程跃迁模型.     

Preparation and Ethanol Sensing Properties of ZnO Nanofibers

ZnO nanofibers with an average diameter of about 90 nm were prepared by an electrospinning method combined with a calcination process. The as-electrospun nanofibers before and after calcination were characterized by means of differential thermal analysis(DTA), thermal gravimetric analysis(TGA), X-ray diffraction(XRD) and scanning electron microscopy(SEM). The fibers after calcination at 600 °C belong to the hexagonal wurtzite structure. The sensor based on ZnO nanofibers exhibited excellent ethanol sensing properties at 206 °C such as good linear dependence in the low concentration(1―100 μL/L), high response, and good selectivity. Fast response(less than 2 s) and recovery(about 16 s) were also observed in our investigations.     

由D型氨基酸设计自组装短肽D-EAK16构建新型三维纳米纤维支架材料

采用D型氨基酸设计自组装短肽D-EAK16, 运用圆二色仪及原子力显微镜等仪器和细胞三维培养, 发现短肽D-EAK16在30 ℃时具有稳定的二级结构β-sheet, 在一定浓度下D-EAK16可形成由纳米纤维构成的透明水凝胶, 含水量高达99％, 可在细胞培养基(如PBS, DMEM)中形成支架. 细胞三维培养显示, 该水凝胶对细胞HO-8910和SPC-A-1的生长未见毒性. 比较D型氨基酸纳米支架和L型氨基酸纳米支架, 细胞的毒性未发现显著性差异. 采用D型氨基酸构建的自组装短肽, 可提供一个三维基质培养系统, 期望能广泛应用于生物医学工程等领域.     

Preparation and characterization of crosslinked chitosan-based nanofibers

Crosslinked chitosan-based nanofibers were successfully prepared via electrospinning technique with heat mediated chemical crosslinking followed.The structure,morphology and mechanical property of nanofibers were characterized by attenuated total reflection-Fourier transform infrared spectroscopy(ATR-FTIR),scanning electron microscopy(SEM),Instron machine,respec- tively.The results showed that,nanofibers exhibited a smooth surface and regular morphology,and tensile strength of nanofibers improved with increasing of triethylene glycol dimethacrylate(TEGDMA)content.     

Characterization of poly(methyl methacrylate) nanofiber mats by electrospinning process

In this study, the aim is to describe the influence of electrospinning parameters on the morphology, the water wetting property and dye adsorption property of poly(methyl methacrylate) nanofiber mats. Specifically, the effects of solution concentration, solvent type, applied voltage, distance between the electrodes and particulate reinforcement on the diameter and shape of the nanofibers were investigated. All poly(methyl methacrylate) nanofiber mats contained beaded nanofiber structures. With increasing the polymer solution concentration, the average fiber diameter also increased. Poly(methyl methacrylate) nanofiber mat electrospun from dimethylformamide solution resulted in thicker fibers when compared with the mat electrospun from acetone solution. Increasing the electric potential difference between the collector and the syringe tip did not increase the average fiber diameter. Besides increasing the distance between the electrodes resulted in a decrease in the average fiber diameter. When compared with PMMA nanofiber mat, thicker fibers were obtained with silica nanoparticles reinforced nanofiber mat. According to the water contact angle measurements, all poly(methyl methacrylate) nanofiber mats revealed hydrophobic surface property. PMMA nanofiber mat with the highest water contact angle gave rise to the highest dye adsorption capacity.