First order speciation of As using flow injection hydride generation atomic absorption spectrometry with in-situ trapping of the arsine in a graphite furnace

A simple method is described to distinguish between As species that react with sodium tetrahydroborate (III) to form AsH₃ and the naturally occurring As species that are unreactive. Results for this rudimentary or “first order” speciation scheme are reported for biological tissue, aquatic plant material, urine and natural water samples. Biological tissue and aquatic plant samples were briefly solubilized in a mixture of 50% nitric acid, no sample preparation was required for the urine or natural water samples. Organoarsenic species which do not react with sodium borohydride under acidic conditions such as arsenobetaine, arsenocholine and tetramethylarsenic, are converted to As(V) by on-line photo-oxidation or microwave heating in a mixture of 0.5 M NaOH and 0.05 M K₂S₂O₈. The sample is subsequently acidified, reduced with sodium borohydride and the generated arsine is trapped in a heated graphite furnace prior to atomization. The superior detection limit (0.14 ng) of the trapping technique permits the dilution of most types of samples, minimizing or eliminating interference effects. Without photolysis or microwave heating a combined result for As(III), As(V), monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA) is obtained. Results are reported for the first order speciation of As in a suite of certified reference materials (CRMs) including National Research Council (NRC) biological tissues and natural water samples, Community Bureau of Reference (BCR) aquatic plant materials and the National Institute of Standards and Technology (NIST) SRM 267ON urine sample. The determination of a non-hydride forming As fraction in untreated urine and natural water certified reference materials (CRMs) has revealed a species of As previously undetected in NRC seawater CRMs.     

利用原位红外光谱研究钙钛矿复合半导体CH_3NH_3PbI_3的稳定性

利用高压原位红外光谱法实时跟踪监测了CH_3NH_3PbI_3在高压氮气以及不同含量氧气气氛中加热时的变化规律.发现CH_3NH_3PbI_3对氧气十分敏感,当氮气中含有1%(体积分数)的氧气时,CH_3NH_3PbI_3加热到150℃发生分解;继续提高氧气含量到21%,温度升高到100℃时CH_3NH_3PbI_3即发生分解;若在常压高纯氮气中加热,其分解温度则能提高到250℃;若将氮气压力提高到4.0 MPa,CH_3NH_3PbI_3的分解温度进一步提高到270℃.实验结果表明,提高压力和减少环境中的氧含量是改善钙钛矿复合半导体稳定性的有效方法.相应地,复合半导体光电子器件的热处理过程可以在更高的温度下进行,从而有希望获得性能更加优良的钙钛矿复合半导体光电子器件.     

imFASP: An integrated approach combining in-situ filter-aided sample pretreatment with microwave-assisted protein digestion for fast and efficient proteome sample preparation

An integrated sample preparation method, termed “imFASP”, which combined in-situ filter-aided sample pretreatment and microwave-assisted trypsin digestion, was developed for preparation of microgram and even nanogram amounts of complex protein samples with high efficiency in 1 h. For imFASP method, proteins dissolved in 8 M urea were loaded onto a filter device with molecular weight cut off (MWCO) as 10 kDa, followed by in-situ protein preconcentration, denaturation, reduction, alkylation, and microwave-assisted tryptic digestion. Compared with traditional in-solution sample preparation method, imFASP method generated more protein and peptide identifications (IDs) from preparation of 45 μg Escherichia coli protein sample due to the higher efficiency, and the sample preparation throughput was significantly improved by 14 times (1 h vs. 15 h). More importantly, when the starting amounts of E. coli cell lysate decreased to nanogram level (50–500 ng), the protein and peptide identified by imFASP method were improved at least 30% and 44%, compared with traditional in-solution preparation method, suggesting dramatically higher peptide recovery of imFASP method for trace amounts of complex proteome samples. All these results demonstrate that the imFASP method developed here is of high potential for high efficient and high throughput preparation of trace amounts of complex proteome samples.     

Formation, structure and magnetism of the metastable defect fluorite phases AVO3.5+x (A=In, Sc)

We report the preparation and stability of ScVO_3.5+x and the novel phase InVO_3.5+x. AVO_3.5+x (A=Sc, In) defect fluorite structures are formed as metastable intermediates during the topotactic oxidation of AVO₃ bixbyites. The oxidation pathway has been studied in detail by means of thermogravimetric/differential thermal analysis and in-situ powder X-ray diffraction. The oxidation of the bixbyite phase follows a topotactic pathway at temperatures between 300 and 400 °C in air/carbon dioxide. The range of accessible oxygen stoichiometries for the AVO_3.5+x structures following this pathway are 0.00x0.22. Rietveld refinements against powder X-ray and neutron data revealed that InVO_3.54 and ScVO_3.70 crystallize in the defect fluorite structure in space group Fm-3 m (227) with a=4.9863(5) and 4.9697(3)Å, respectively with A³⁺/V⁴⁺ disorder on the (4a) cation site. Powder neutron diffraction experiments indicate clustering of oxide defects in all samples. Bulk magnetic measurements showed the presence of V⁴⁺ and the absence of magnetic ordering at low temperatures. Powder neutron diffraction experiments confirmed the absence of a long range ordered magnetic ground state.     

Low-temperature and stable CO oxidation of Co3O4/TiO2 monolithic catalysts

Highly efficient Co₃O₄/TiO₂ monolithic catalysts with enhanced stability were in-situ grown on Ti mesh for CO oxidation,which could completely oxidize CO at 120℃.The comprehensive catalytic performance is competitive to some noble metal catalysts and conventional Co₃O₄ powder catalysts,which holds great potential toward industrial applications.Meanwhile,the in-situ synthesis strategy of Co₃O₄/TiO₂ monolithic catalysts on flexible mesh substrate in this work can be extended to the development of a variety of oxide-based monolithic catalysts towards diverse catalysis applications.     

二氧化钛纳米粒子-氧化石墨烯/聚酰亚胺混合基质膜的原位聚合及气体渗透性能

以钛酸四丁酯为前驱体,采用浸渍-沉淀法制备二氧化钛纳米粒子-氧化石墨烯(TiO_2-GO)复合物,再将TiO_2-GO复合物与4,4'-(六氟异亚丙基)邻苯二甲酸酐和4,4'-二氨基二苯醚通过原位聚合构建TiO_2-GO/TiO_2-GO/PI(聚酰亚胺)混合基质膜,用于CO_2的渗透脱除.采用傅里叶变换红外光谱(FTIR)、拉曼光谱(Raman)、透射电子显微镜(TEM)、扫描电子显微镜(SEM)、热失重(TG)和Zeta电位等表征了TiO_2-GO复合物和TiO_2-GO/PI混合基质膜的形貌与结构;探讨了TiO_2掺杂量对TiO_2-GO复合物及TiO_2-GO/PI混合基质膜的结构和气体渗透性能的影响.结果表明,TiO_2-GO复合物中TiO_2纳米粒子较均匀地沉积在GO片层上,TiO_2纳米粒子在形成的同时破坏了GO的结构,使其无序度增加.TiO_2的掺杂对TiO_2-GO/PI混合基质膜的形貌与结构影响较小,但提升了TiO_2-GO/PI混合基质膜的CO_2和N2渗透性能.但过量的掺杂使TiO_2粒子在GO片层上团聚,从而导致TiO_2-GO复合物在混合基质膜中的分散性变差,CO_2渗透性及CO_2/N2渗透选择性降低.当TiO_2掺杂质量分数为30%时,TiO_2-GO/PI混合基质膜的CO_2渗透性为360 Barrer[1 Barrer=10~(-10)cm~3(STP)·cm/(cm~2·s·cm Hg)=7.5×10~(-14)cm~3(STP)·cm/(cm~2·s·Pa)],CO_2/N_2的渗透选择性可达31.     

甲醛还原Pt/TiO2催化剂用于温和条件下高效催化氧化甲醛

通过浸渍法(IM)和沉积-沉淀(DP)法制备了一系列Pt/TiO2(P25)催化剂,并分别用甲醛溶液和氢气还原处理催化剂.利用原位红外监测催化剂表面吸附物种在反应过程中的变化,探究了催化剂制备和还原条件及Pt负载量对催化剂结构和催化氧化甲醛活性的影响.结果显示,用DP法制备并用甲醛还原的Pt/P25催化剂中Pt颗粒分散均匀,并具有合适的粒径和高浓度的表面活性氧,显示出良好的甲醛氧化活性.在空速30000 ml/(g·h)、反应温度30°C和甲醛初始浓度50 mg/m3的条件下,0.4%Pt/P25(DP-HCHO)上的甲醛转化率达到98%,并能稳定运行100 h以上.相比之下, Pt/P25(DP-H2)由于表面活性氧较少,不利于甲酸盐氧化,活性较低. Pt/P25(IM-H2)虽然具有高浓度的表面活性氧,却同时具有最大的Pt颗粒粒径,在甲醛转化为甲酸盐和甲酸盐氧化两步反应中的活性均较差,因而甲醛氧化活性最差.     

Nano/micro-scale morphologies of semi-interpenetrating poly(ε−caprolactone)/tung oil polymer networks: Isothermal and non−isothermal crystallization kinetics

The isothermal and non-isothermal crystallization kinetics of pure poly(ε−caprolactone) (PCL) and its blends with crosslinked tung oil were investigated as a function of composition, crystallization temperature, and heating rate using differential scanning calorimetric (DSC). The PCL/tung oil semi-interpenetrating polymer networks of different compositions were prepared via cationic polymerization of tung oil in the presence of homogenous solutions of PCL. This unique and relatively new in-situ polymerization and compatibilization blending technique created nano/micro-scale morphologies that cannot be obtained with the traditional melt-processing and/or solvent casting methods. Blends with different miscibility, phase behaviors, and morphologies (miscible, partially miscible, and immiscible) were observed as a function of composition with a constant concentration of boron trifluoride diethyl etherate (BFE) cationic initiator. The morphology of the semi-interpenetrating polymer networks was performed using scanning electron microscopy (SEM). Miscible blends with a single T_g for PCL ≤ 10 wt.%. were observed. While, on the other hand, partially miscible blends with two distinct T_gs and nanoscale morphologies and average particle sizes as small as 100 nm were observed for blends with 20 ≤ PCL wt.% ≤ 30. Immiscible blends with microscale highly interconnected, co-continuous two-phase morphology and two distinct T_gs were detected for 50 wt.% PCL. Both isothermal and non-isothermal crystallization kinetics were strongly influenced by the different miscibility and morphology of the blends. The isothermal and non-isothermal crystallization kinetics of PCL/tung oil blends were analyzed on the basis of Avrami and modified Avrami approaches, respectively. A substantial decrease in the isothermal (longer half time) and non-isothermal (T_m shifted to lower temperature) crystallization kinetics was observed as the concentration of PCL increased in the blends up to 30 wt.% due to the partially miscibility of the blends in this composition range. In a contrast, for 50 wt.% PCL blend, a considerable increase in the crystallization kinetics (isothermal and non-isothermal) was detected due to the highly interconnected, co-continuous two-phase morphology.     

Headspace solid phase microextraction in-situ supercritical fluid extraction coupled to gas chromatography-tandem mass spectrometry for simultaneous determination of perfluorocarboxylic acids in sediments

Headspace solid phase microextraction (HS-SPME) in-situ supercritical fluid extraction (SFE) was investigated for the determination of trace amounts of perfluorocarboxylic acids (PFCAs) in sediments. Quantitation was performed by using gas chromatography coupled to negative chemical ionization-tandem mass spectrometry (GC-NCI-MS/MS). The optimum conditions of HS-SPME following SFE were obtained using 500 μL n-butanol as a derivatization reagent in supercritical carbon dioxide with static extraction for 10 min, then dynamic extraction for 20 min at 30 MPa and 70 °C and simultaneous collected with 100 μm film thickness PDMS fiber. The linear range of proposed method was from 5 to 5000 ng g(-1), with limit of detection ranging from 0.39 to 0.54 ng g(-1) and limit of quantitation ranging from 1.30 to 1.80 ng g(-1). The developed method was successfully applied to analyze PFCAs in sediments from rivers and beach near industrial areas. The concentrations of PFCAs determined are from 282 to 4473 ng g(-1).     

天水仙人崖石窟壁画颜料层原位-无损分析研究

壁画是我国极为重要的文化遗产类型,具有极高的历史价值、艺术价值、科学价值、文化价值和社会价值。颜料层作为壁画的核心价值所在,包含古代历史文化、宗教信仰、政治经济、科学技术等多方面的信息内涵。常规的颜料层分析方法有原位无损和微损取样两种,取样分析方法虽能满足这类珍贵、脆弱文物的研究,但获取样品数量有限且会对本体造成不可逆转的损伤。综合运用数字成像以及光谱等分析技术对天水仙人崖石窟壁画颜料层进行工艺与制作材料研究。结果显示,正射影像图能够真实记录壁画当前纹理信息,色度仪可以量化表征壁画颜料的颜色,红紫外摄影可以提取可见光下不易探查的壁画绘制线稿、修复痕迹等隐含信息,高倍数码显微镜可观察壁画表面的微观形态及破损处的层次信息,便携式X射线荧光光谱仪可检测出颜料中的元素由此判断主要显色元素,高光谱采集所得数据与标准图谱比较后能够准确判定颜料的矿物种类。因此,多种原位无损分析方法的联合运用,可以减少对文物的直接干预,亦可达到对壁画颜料层认知的目的。这些非接触式的无损检测方法,可精细化研究壁画颜料层的色彩、物理、化学属性等内容,是壁画现场分析的重要手段,可在石窟寺、寺观殿堂、墓葬壁画的研究上进行推广,发挥其应有之用。