Conductivity and dielectric properties of sol–gel derived porous zirconia

The 8-mol percentage Y₂O₃-stabilized Porous Zirconia was prepared using sol–gel method. Zirconium oxalate gel was prepared by the addition of appropriate amount of oxalic acid solution into the 1 M aqueous solution of zirconium-oxy chloride. A cubic phase zirconia powder was obtained by calcination and milling of the zirconium oxalate gel. Crystallization temperature was found about 450 °C from the Differential thermal analysis. The phase analysis by X-ray diffraction shows the presence of cubic phase. Pellets sintered at 1,350 °C were highly porous, and the electrical conductivity was found with lower value due to the porosity, and the hardness was about 8.0 GPa. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Magnetic properties of multiwalled carbon nanotubes as a function of acid treatment

We investigate the electronic properties of multiwalled carbon nanotubes both before and after acid treatment with concentrated sulphuric and nitric acids. Magnetic susceptibility measurements were performed using a SQUID magnetometer and show that there is a considerable enhancement in the density of states at the Fermi level. The data shows that the diamagnetic influence from the graphitic nanotubes dominates. We experimentally observe, after acid treatment, that the diamagnetic susceptibility remains unchanged at 5 K but notably decreases at 77 K. We propose the acid treatment has increased the Van Vleck paramagnetic contribution lowering the diamagnetic response from the π-electron orbital magnetisation. The Van Vleck paramagnetic contribution is finite-temperature dependent with a diminishing contribution at higher fields.     

掺杂对碳纳米管拉曼光谱及场发射性能的影响

采用高温热解法在860℃分别制备出了镓、氮以及硼和氮掺杂的碳纳米管,提纯后利用丝网印刷工艺分别将它们制备成薄膜,并测试了它们的拉曼光谱与场发射性能。测试结果表明,掺杂纳米管的缺陷密集度比纯碳纳米管明显增大,而它们的场致电子发射性能则与掺杂元素的性质密切相关。镓和氮掺杂的纳米管均具有非常优异的场发射性能,而硼和氮共掺杂的纳米管的场发射性能很差。掺杂引起碳纳米管费米能级附近能态密度的变化及功函数的降低是其具有优异场致电子发射性能的主要原因。     

Nanoscale surface of carbon nanotube fibers for medical applications: Structure and chemistry revealed by TOF-SIMS analysis

Surface structure and related chemistry understanding is a vital element in the design of high biocompatible materials since adsorption and adhesion of biological components are involved. These features are even more important in the case of nanostructured materials such as carbon nanotubes (CNTs) fibers. In our preliminary work we synthesised CNTs based fibers for medical applications. This new hybrid system combines polyvinyl alcohol (PVA) with CNTs and polylactic-co-glycolic acid (PLGA), a biodegradable copolymer. The surface properties of this material are investigated in order to guarantee a biocompatible response. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) was found to be an ideal tool for fiber characterisation owing to its capacity to provide chemical specificity combined with detection limits beyond the reach of techniques previously used. Complementary morphological information is provided by atomic force microscopy (AFM). The corroboration of both data enables us to define the chemistry and structure of this new formulation.     

掺Eu3+硅基材料的发光性质

通过溶胶－凝胶技术制备了掺Eu^3 的硅基材料并测试了其三维荧光光谱、激光谱和发射光谱，结果显示，最佳激发波波长为350nm,最强荧光波长为620nm；在350nm光激发下的发射光谱显示Eu^3 的特征发射光谱，产生4条谱带，分别是577nm(^5D0-^7F0)，588nm(^5D0-^7F1),596nm(^5D0-^7F1)和610nm(^5D0-^7F2)。     

Au deposits on graphite: On the nature of high temperature desorption peaks in CO thermal desorption spectra

Due to the discovery of Au as a catalyst for low temperature CO oxidation, the adsorption of CO on Au surfaces has attracted a lot of attention recently. On stepped and rough single crystal surfaces as well as on deposited particles two characteristic desorption states above 100 K have been observed via TPD. We have studied Au deposits on graphite in order to elucidate the nature of these desorption peaks in more detail. For this purpose, Au was deposited at 100 K and 300 K on HOPG as a weakly interacting support. In analogy to other supports, we obtain two desorption states (∼140 K and ∼170 K) whose relative intensities depend strongly on the deposition temperature with the high temperature peak being much more pronounced for the 100 K deposits. After annealing to 600 K, both states drastically lose intensity. XP spectra, on the other hand, show virtually no decrease of the Au 4f intensity as would be expected for desorption or significant changes of the particle morphologies. We conclude that both desorption peaks are defect-related and connected with under-coordinated Au atoms that are lost for the most part upon annealing. These sites could be located at the perimeter of dendritic islands or on small, defect-rich particles in addition to larger particles not adsorbing CO at 100 K. Preliminary STM results are in favour of the second interpretation.     

Electronic spectra of cationic forms of meso-tetrapropylporphin in a nanoporous silicate gel matrix

We have studied the fluorescence and fluorescence excitation spectra at 300 K, 77 K, and 4.2 K for silicate gel matrices colored with meso-tetrapropylporphin by impregnation of the matrix with a solution of the pigment. Comparison of the data obtained with the absorption spectra in acidified solutions and analysis of the low-temperature fine-structure vibronic spectra, and also taking into account data obtained earlier for octaethylporphin in a xerogel showed formation of two cationic forms of meso-tetrapropylporphin in the gel matrix: the short-wavelength form has a dicationic structure, while the long-wavelength form has a monocationic structure. We have traced out the correlations of the vibrational structure in the spectra of the dicationic form with data for the porphin dication, and we have drawn a number of conclusions concerning the normal vibrational modes that are active in the vibronic fluorescence and absorption spectra of the studied cationic forms. Using the AM1 semiempirical quantum chemical method, we optimized the geometry of the mesotetrapropylporphin dication: the most stable of the possible conformers is the dication structure with saddleshaped macrocycle nonplanarity. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 73, No. 4, pp. 453–461, July–August, 2006.     

Study of the spontaneous formation of organic layers on carbon and metal surfaces from diazonium salts

This study investigates the spontaneous grafting of different para-substituted phenyl groups on carbon and metallic surfaces from diazonium salts solutions. Glassy carbon, nickel, zinc and iron plates were allowed to react with an acetonitrile solution of aryldiazonium tetrafluoroborate salt by simple dipping. The surfaces were characterized before and after their immersion by XPS and AFM to evidence the formation of a coating on the different materials. The results are indicative of the presence of substituted phenyl groups on all the investigated surfaces. This study also aims at correlating grafting efficiency with metal reactivities and diazonium salt electronic properties by means of AFM and FT-IRRAS. For this purpose, zinc and nickel were chosen due to their opposite reducing properties and two diazonium salts were selected with electron-donor or -withdrawing para-substituents. The results tend to indicate that redox properties of both partners (diazonium + metal) are of prime importance for grafting to occur.     

溶胶-凝胶VO2薄膜转换特性研究

利用溶胶凝胶法在SiO2Si衬底上沉积高取向的V2O5薄膜,在压强低于2Pa,温度高于400℃的条件下,对V2O5薄膜进行真空烘烤,获得了电阻率变化3个数量级以上、弛豫宽度为62℃的VO2多晶薄膜.以X射线衍射(XRD)、扫描电子显微镜(SEM)图和电阻率转换特性等实验结果为依据,详细分析了溶胶凝胶薄膜在真空烘烤时从V2O5向VO2的转化,它经历了从VnO2n+1(n=2,3,4,6)到VO2的过程.实验证明,根据选择合适的成膜热处理条件和真空烘烤条件是实现溶胶凝胶V2O5结构向VO2结构成功转换的关键 关键词： 溶胶-凝胶法 氧化钒薄膜 VO2膜转换特性     

Modeling of environmentally significant interfaces: Two case studies

When some parameters cannot be easily measured experimentally, mathematical models can often be used to deconvolute or interpret data collected on complex systems, such as those characteristic of many environmental problems. These models can help quantify the contributions of various physical or chemical phenomena that contribute to the overall behavior, thereby enabling the scientist to control and manipulate these phenomena, and thus to optimize the performance of the material or device. In the first case study presented here, a model is used to test the hypothesis that oxygen interactions with hydrogen on the catalyst particles of solid oxide fuel cell anodes can sometimes occur a finite distance away from the triple phase boundary (TPB), so that such reactions are not restricted to the TPB as normally assumed. The model may help explain a discrepancy between the observed structure of SOFCs and their performance. The second case study develops a simple physical model that allows engineers to design and control the sizes and shapes of mesopores in silica thin films. Such pore design can be useful for enhancing the selectivity and reactivity of environmental sensors and catalysts. This paper demonstrates the mutually beneficial interactions between experiment and modeling in the solution of a wide range of problems.