Preparation of Low-dielectric Permittivity Polyimide Resins with High Surface Activity from Chemically Bonded Hyperbranched Polysiloxane

Thermosetting resin matrix is the key component of advanced wave-transparent composites,where low dielectric constant,excellent processability,high thermal stability,as well as good bonding ability are required for resins.Herein,we prepared a series of phenylethynyl terminated polyimide(PI)resins by grafting amine-functionalized hyperbranched polysiloxane(HBPSi)to PI chains during the in situ polymerization.The effects of HBPSi on the processability of oligomers,molecular packing,thermal stability,dielectric property and bonding ability to reinforce Kevlar fibers of the cured PI/HBPSi composite resins have been examined in detail.The dielectric constants of the cured composite resins were greatly reduced from 3.29 to 2.19 without compromising its processability and thermal stability.Meanwhile,the 10 wt％HBPSi-containing PI resin demonstrated better bonding ability to reinforce fibers with the interfacial shear strength(IFSS)of 37.64 MPa,compared with that of neat PI-6 matrix(27.34 MPa),and better adhesion to metal with the lap shear strength of 10.48 MPa,50％higher than that of neat resin PI-6(6.98 MPa).These resultant PI/HBPSi composite resins exhibit excellent comprehensive properties,indicating their great potential as low-dielectric constant resin matrix in radar radome.     

高力学强度细菌纤维素气凝胶纤维的连续化制备

气凝胶纤维因其高外表面积和高柔韧性在能量管理系统中具有潜在应用而引起了广泛关注.但是,目前制备的气凝胶纤维力学强度较低,限制了其实际应用.为提高气凝胶纤维力学性能,在始终保持细菌纤维素(BC)纳米纤维处于湿态下,利用NaOH/尿素/硫脲复合溶剂直接低温溶解原生BC,获得透明的BC纺丝原液;通过湿法纺丝制备了BC水凝胶纤维,经过水洗和冷冻干燥后处理,制得BC气凝胶纤维.采用偏光显微镜(POM)、13C核磁共振(13C-NMR)和高级旋转流变仪研究BC在复合溶剂中的溶解过程与状态;利用全反射傅里叶变换红外吸收光谱(ATR-FTIR)、X射线衍射(XRD)和热失重(TG)研究BC溶解前后结构与性能变化;利用场发射扫描电镜(FESEM)、全自动比表面积和孔径分布分析仪、单丝强力仪对获得的BC气凝胶纤维结构与性能进行表征.结果表明,复合溶剂在?15℃条件下可以直接溶解原生湿态BC,最高溶解浓度为3 wt%;采用湿法纺丝制得高度多孔的连续BC气凝胶纤维,比表面积高达192 m^2/g且具有优异的力学性能,断裂强度和杨氏模量高达(9.36±1.68)MPa和(176±17.55)MPa,如0.4 mg BC气凝胶纤维可以支撑高于其本身质量5×10^4倍的重物.     

基于云环境的分布式软件接口自动化测试

软件测试是保证软件质量,提供可靠服务的重要技术手段。目前基于Web Service的分布式软件越来越多,其测试技术手段也越来越受到关注。Web Service的分布性和多样性使手工测试变得非常低效,因而需要不断提高Web Service测试的自动化程度。另外,云计算因其计算成本低、可伸缩性强的特点为自动化测试提供了新的支持环境。本文结合Web Service的测试需求,首次提出了基于云环境的Web Service接口自动化测试的技术框架,分析了框架内原子Web Service、组合Web Service测试的关键技术,并研发了基于CloudStack云平台的自动化测试的原型系统。实验结果表明,本文所提出的基于云平台的WebService自动化测试方案可行且提高了测试效率。     

Preparation of Polyaniline/Au0 Nanocomposites Modified Electrode and Application for Hydrazine Detection

The PANI/Au₀ nanocomposite films were successfully prepared on glassy carbon electrode (GCE) using a simple alternate adsorption of water soluble polyaniline (PANI) and . The growth of the films was monitored by UV? Vis spectroscopy and cyclic voltammetry. was in‐situ reduced in the film due to the redox interaction between PANI and , without extra reductant. The ultrafine Au nanoparticles with the size of 2–4 nm were observed by transmission electron spectroscopy. The existence of zero‐valence Au nanocrystals (Au₀) was confirmed by X‐ray photoelectron spectroscopy, X‐ray Diffraction and FTIR. PANI in the nano‐structured PANI/Au₀ composite films displayed a good redox activity in neutral pH solution. The as‐obtained PANI/Au₀/GCE presents an excellent electrocatalytic activity to hydrazine oxidation, and the mechanism of hydrazine oxidation was studied. The calibration curve on (PANI/Au₀)₅/GCE was obtained in the concentration range of 0.01–6 mM with the detection limit of 1 µM (S/N>3). The modified electrode has a great potential for hydrazine sensor application due to its ease of fabrication, good reproducibility and high stability.     

Preparation and evaluation of PANI/PTT electromagnetic shielding fabric by in-situ chemical polymerization

To prepare the flexible and stretchable electromagnetic shielding (EMS) fabric with environmental stability, this paper uses polytrimethylene terephthalate (PTT) fabric as substrate, the aniline monomer as raw material, hydrochloric acid (HCl) as the doping agent, ammonium persulfate (APS) as the oxidant to produce polyaniline (PANI)/PTT electromagnetic shielding fabric by in-situ chemical polymerization. It studies the influence of APS and HCl concentration on the surface electrical resistance and the absorption loss of electromagnetic shielding fabric. It can be observed that an increasing APS and HCl facilitate the absorption and spread of PANI into PTT fabric to form a conductive network, and improve the absorption loss efficiency, while the excess APS and HCl will hinder the PANI polymerization. The high electrical conductivity and absorption loss of the PANI/PTT fabric are obtained at the concentration of An 0.4 M, APS 0.4 M, HCl 1.25 M, and polymerization reaction time 120 min. Meanwhile, in-situ polymerization of PANI does not introduce new impurities and destroy the molecular structure of PTT.     

Preparation and thermal properties of poly[acrylonitrile-co-(β-methylhydrogen itaconate)] used as carbon fiber precursor

In order to replace terpolymer with bipolymer, a bifunctional comonomer β-methylhydrogen itaconate (MHI) containing carboxyl group and ester group was synthesized to prepare poly[acrylonitrile-co-(β-methylhydrogen itaconate)] [P(AN-co-MHI)] bipolymers used as carbon fiber precursor for improving the stabilization and spinnability at the same time. The P(AN-co-MHI) bipolymers with different monomer feed ratios were characterized by elemental analysis, Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The results show that both the polymerization conversion and molecular mass of P(AN-co-MHI) reduce with the increasing MHI amounts in the feed due to the larger molecular volume of MHI than acrylonitrile (AN). The monomer reactivity ratios were calculated by Fineman–Ross and Kelen–Tüdõs methods, the results show good agreement and MHI possesses higher reactivity than AN. Two parameters $ E_{\text{s}} = A_{{1,629\,{\text{cm}}^{ - 1} }} /A_{{2,244\,{\text{cm}}^{ - 1} }} $ and $ SI = (I_{0} - I_{\text{S}} )/I_{0} $ were defined to evaluate the extent of stabilization, and the activation energy (E _a) of the cyclization was calculated by Kissinger method and Ozawa method. The FTIR, XRD, and DSC results show that P(AN-co-MHI) bipolymers exhibit significantly improved stabilization characteristics than PAN homopolymer, such as larger extent of stabilization, lower initiation temperature, and smaller E _a of cyclization, which is attributed to the ionic initiation by MHI comonomer and it is beneficial to preparing high-performance carbon fiber.     

Coloring properties of novel 1,4-distyrylbenzene and 4,4′-distyrylbiphenyl fluorescent brighteners and their arrangement in cotton and polyester fiber

Some novel 1,4-distyrylbenzene (DSB) and 4,4′-distyrylbiphenyl (DSBP) fluorescent brighteners (FBs) were used to dye polyester and cotton fabrics. The CIE whiteness, color hue and reflectance spectrum of dyed fabrics were compared. DSBP derivatives could dye the cotton and polyester fabrics with a higher whiteness level and had a lower fluorescent quenching concentration than DSB derivatives. The color hue for the fabric dyed with DSB FBs was yellow-green, whereas that dyed with DSBP was blue–violet. The molecular arrangement in the fiber had a significant influence on their optical properties, resulting in different coloring properties. The increase in molecule planarity and rigidity generated by the interaction between the polymer and FB molecules caused a remarkable bathochromic shift in emission and excitation spectra. The H-aggregate of the DSB molecule in the fiber was easily generated, and the degree of aggregation increased with the molecular polarity. However, the aggregation of DSBP molecules in the polyester and cotton fiber was not found. The surface region of the cotton fiber was filled with FB molecules, whereas FB molecules in the polyester fiber aggregated easily, and incident light could pass through the surface region.     

Synthesis and characterization of acetylated sept-D-glucopyranose carbamate as an oligosaccharide donor简

An oligosaccharide donor, acetylated sept-o-glucopyranose tetradecyl carbamate, was designed and synthesized. This compound could be easily linked to hydroxyl-containing compounds through an Oglycosidic bond. Characterization of all the oligosaccharide intermediates and the final product was thoroughly discussed.     

高效液相色谱-串联质谱法测定染发剂中11种苯胺和苯酚类染料

1引言在众多染发剂产品中,人工合成的氧化型染发剂由于染色效果好、色调丰富、颜色持久等优点,应用极为广泛。但这类染发剂多以芳香胺和/或酚类组分为有效成分,易引起人体过敏等不良反应,长期使用甚至可能导致"三致"。鉴于氧化型染发剂的安全性问题,我国《化妆品卫生规范》明确规定了其禁用和暂时允许使用组分的类别及限制条件,并推荐