一种新的岩石非线性黏弹塑性蠕变模型研究

为了克服传统元件组合模型不能描述岩石蠕变过程中非线性特征的缺陷，首先根据加速蠕变阶段的应变和应变率随蠕变时间急剧增大的特点，建立黏塑性应变与蠕变时间的指数函数关系并提出非线性黏塑性体．将该非线性黏塑性体与广义Burgers蠕变模型串联，建立可以描述岩石全蠕变过程的非线性黏弹塑性蠕变模型，根据叠加原理得到一维应力状态下的轴向蠕变方程．然后基于塑性力学理论指出岩石三维蠕变本构方程建立过程中的不足之处，并给出非线性黏弹塑性蠕变模型合理的三维蠕变方程．最后采用不同应力水平下砂岩轴向蠕变试验对模型合理性进行验证，结果表明：拟合曲线与试验曲线吻合度较高，所建蠕变模型能够很好地描述砂岩在不同应力水平下的蠕变变形规律，尤其对加速蠕变阶段的非线性特征描述效果很好，验证了模型的合理性．     

小孔流速实验中的排水时间和流量系数的研究

本文以水作为理想流体,考虑到水头损失和孔口缩流效应,对小孔流速实验涉及的容器排水问题进行了系统的理论和实验研究.从理论上推导得出了圆柱形容器排水时间的解析解,分析了排水时间和自由液面速度、流量系数之间的规律,提出了排水时间的等效性.实验上,加工了底部开有不同小孔的大型圆柱形容器,测量了容器排水时间随液面高度的变化关系,借助实验结果计算了流量系数值,验证了容器排水时间的等效性关系,实验结果与理论计算符合较好.     

双稳态结构中的1/2次谐波共振及其对隔振特性的影响

以典型的双稳态系统——屈曲梁结构为例,基于等效模型,结合解析、数值和实验手段,研究了双稳态结构中的1/2次谐波共振特性、演化过程、参数调节规律及其对隔振特性的影响.研究发现,当非线性刚度系数或激励幅值增加到一定程度时,系统会在一定带宽下产生显著的1/2次谐波共振;随着激励幅值增加,阻尼系统的1/2次谐波遵循“产生-增强-衰退-消失”的过程,该过程对峰值频率和峰值传递率有重要影响;适当提高非线性强度能有效改善双稳态结构隔振特性.针对双稳态屈曲梁结构开展的实验验证了1/2次谐波特性和隔振特性变化规律.     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

Structure and Properties of Silumin Surface after Vacuum Arc Plasma-Assisted Deposition of Coatings Irradiated by Low Energy High Current Pulsed Electron Beam

Russian Physics Journal - The paper presents the results of modification of the silumin surface layer using a multicycle processing technique which combines the formation of the film...     

80.5 MeV/u碳离子诱发铜靶的放射性剩余产物测量

高能重带电粒子能直接穿透靶原子核外电子层,与原子核发生直接碰撞,发生散裂反应,产生一系列具有放射性的剩余产物核.重带电粒子诱发靶材放射性剩余核与辐射防护和人员安全有着密切联系,当前,大部分剩余核产额主要依靠蒙特卡罗粒子输运程序进行模拟计算,其准确程度亟需通过实验测量进行准确评估.本文利用能量为80.5 MeV/u的(12)^C⁶⁺粒子对薄铜靶开展了辐照实验与伽玛射线测量,结合伽玛谱学分析方法,得出了辐照产生的18种放射性剩余产物的初始活度和产生截面值,并与PHITS模拟结果进行对比.结果表明,PHITS模拟程序对放射性剩余核种类的估计具有较高可靠性,在其绝对产额方面,与实验测量仍具有较大偏差.     

Gradient structure of polypropylene composites filled with carbon black

Russian Chemical Bulletin - Gradient polymer composites were prepared by melt-mixing of carbon black and polypropylene in a compounder and subsequent hot pressing of pellets. The thermally treated...