Alloying by high dose ion implantation of iron into magnesium and aluminium

Alloys of the systems Fe–Al (mixable over the whole concentration range) and Fe–Mg (insoluble with each other) were produced by implantation of Fe ions into Al and Mg, respectively. The implantation energy was 200 keV and the ion doses ranged from 1 × 10₁₄ to 9 × 10₁₇cm^-2The obtained implantation profiles were determined by Auger electron spectroscopy depth profiling. Maximum iron concentrations reached were up to 60 at.% for implantation into Al and 94 at.% for implantation into Mg. Phase analysis of the implanted layers was performed by conversion electron Mössbauer spectroscopy and X‐ray diffraction. For implantation into Mg, two different kinds of Mössbauer spectra were obtained: at low doses paramagnetic doublets indicating at least two different iron sites and at high doses a dominant ferromagnetic six‐line‐pattern with a small paramagnetic fraction. The X‐ray diffraction pattern concluded that in the latter case a dilated αiron lattice is formed. For implantation into Al, the Mössbauer spectra were doublet structures very similar to those obtained at amorphous Fe–Al alloys produced by rapid quenching methods. They also indicated at least two different main iron environments. For the highest implanted sample a ferromagnetic six‐line‐pattern with magnetic field values close to those of Fe₃Al appeared.     

State of and prospects for XeF(C−A) optically pumped lasers

Experimental and theoretical results are presented on an XeF(C?A) blue-green laser driven by 5-kJ energy. The laser was pumped by a ferrite-induced discharge of 90 cm in length. The output energy of 0.22 J was obtained with a plane-parallel resonator. A program to simulate laser operation has been developed. Numerical results for a wide range of conditions are compared with experiments performed by us and by other authors. It is found that intracavity refractive losses limit laser operation for XeF pressures above 3 torr. The laser efficiency strongly depends on the discharge-to-cavity length ratio. Possible ways to increase the laser power and efficiency are discussed.     

Why define atoms in real space?

The physics of a system is determined by a variation of the action integral, i.e., by a variation of the space–time volume integral of the Lagrange function. If one demands that the properties of an atom in a molecule be derived from physics, the atom must generate its own space–time volume, requiring that its boundaries be defined in real space. The variations in the action are related to the actions of generators of infinitesimal unitary transformations. In the general case, the action integral is altered by generators acting in both the spacelike and timelike surface bounding the space–time volume, whereas for a total isolated system, the physics is totally determined by their action in just the spacelike surfaces at the two time endpoints. It is shown and illustrated for a one-dimensional system that the definition of an atom corresponds to the possibility of choosing a subsystem in such a way that the contributions to the change in action resulting from the evolution in time of its spatial boundaries vanishes identically. The properties of these subsystems and of the total system of which they are a part are, therefore, determined by one and the same action principle. This choice of subsystem corresponds to the possibility of augmenting the Lagrange function by the divergence of the gradient of the electron density a step that, while leaving the equations of motion unchanged, modifies the generating operators in the required manner. © 1994 John Wiley & Sons, Inc.     

Three-dimensional atom probe study of the segregation behaviour of Ni91Pt9 alloy after sputtering

To investigate local ordering and segregation phenomenon in a Ni91Pt9-alloy after sputtering and annealing a 3D optical atom probe (OAP) has been used. The specimen tips have been prepared from polycrystalline samples. To sputter the samples a separate preparation chamber with a scannable Ar-sputter-gun is connected to the OAP vessel. When necessary, the sample can be electrically heated to induce segregation and cure the altered layer. After a heat treatment of a Ni91 at. %Pt 9 at.% specimen at 1100 K the surface of a (111)-oriented specimen is enriched in platinum by a factor of two in relation to the bulk. The phenomenon of short-range ordering has been investigated on the surface and in the subsurface volume. A 3D reconstruction of this annealed NiPt specimen shows regions with high concentration of platinum that gives an indication at short-range ordering. Uniform sputtering of the tip without a heat treatment induces a decisive depletion of Pt on the surface and the following subatomic layers. The atom-probe results of specimens in thermal equilibrium are in close agreement to further surface sensitive results obtained from Ion Scattering Spectroscopy (ISS) and Auger Electron Spectroscopy (AES).     

Local and Parallel Finite Element Algorithms for Eigenvalue Problems

Abstract Some new local and parallel finite element algorithms are proposed and analyzed in this paper foreigenvalue problems.With these algorithms, the solution of an eigenvalue problem on a fine grid is reduced tothe solution of an eigenvalue problem on a relatively coarse grid together with solutions of some linear algebraicsystems on fine grid by using some local and parallel procedure.A theoretical tool for analyzing these algorithmsis some local error estimate that is also obtained in this paper for finite element approximations of eigenvectorson general shape-regular grids.     

Study of the charge-exchange reactions\pi ^ - p \to (\pi ^0 ,\eta ,\eta \prime )n at 63 GeV

Muon electron pairs were detected in an Al multiplate spark chamber, exposed to a neutrino beam from the CERN PS. The leptons were not accompanied by other particles, except occasionally by protons. The background came mainly from muon associated π⁰ production, with one decay gamma lost. It was determined empirically, together with the small contribution from υ _e reactions. For electron energies above 2 GeV the background is 5.7±1.5 events, whereas 18 (μe)-candidates have been observed. Hence the effect is established, with a rate of about 10^?4 as compared to the muonic reactions above 3 GeV. Charm creation as the origin of this (μe)-production process is excluded; heavy neutral lepton production does not fit the kinematics observed. Instead the events are compatible with the two-body decay of an object with variable invariant mass of order 1 GeV, possibly resulting from axion interactions.     

A comparison of steady-state evoked potentials to modulated tones in awake and sleeping humans.

Steady-state evoked potential responses were measured to binaural amplitude-modulated (AM) and combined amplitude- and frequency-modulated (AM/FM) tones. For awake subjects, AM/FM tones produced larger amplitude responses than did AM tones. Awake and sleeping responses to 30-dB HL AM/FM tones were compared. Response amplitudes were lower during sleep and the extent to which they differed from awake amplitudes was dependent on both carrier and modulation frequencies. Background EEG noise at the stimulus modulation frequency was also reduced during sleep and varied with modulation frequency. A detection efficiency function was used to indicate the modulation frequencies likely to be most suitable for electrical estimation of behavioral threshold. In awake subjects, for all carrier frequencies tested, detection efficiency was highest at a modulation frequency of 45 Hz. In sleeping subjects, the modulation frequency regions of highest efficiency varied with carrier frequency. For carrier frequencies of 250 Hz, 500 Hz, and 1 kHz, the highest efficiencies were found in two modulation frequency regions centered on 45 and 90 Hz. For 2 and 4 kHz, the highest efficiencies were at modulation frequencies above 70 Hz. Sleep stage affected both response amplitude and background EEG noise in a manner that depended on modulation frequency. The results of this study suggest that, for sleeping subjects, modulation frequencies above 70 Hz may be best when using steady-state potentials for hearing threshold estimation.