Characterization of cellulose fibers electrospun using ionic liquid

Nonwoven fibers of cellulose were obtained by electrospinning of cellulose in an ionic liquid, 1-butyl-3-methylinmidazolium chloride (BMIMCl), which is known to be one of the non-volatile solvents. The electrospinning setup was modified in such a way that the syringe was contained in a constant-temperature chamber because of the high melting point of BMIMCl, and the electrospun fibers were collected on the water, which immediately removed the remnant solvent from the electrospun cellulose fibers. The effect of the viscosity of the cellulose solution in BMIMCl on the size and the structure of the fibers was investigated. The crystalline structure of cellulose was examined by X-ray diffraction. Also, the effect of dimethyl sulfoxide, which was expected to induce swelling of cellulose, was studied. The minimum diameter of the continuous electrospun cellulose fibers obtained in this work ranged between 500 and 800 nm.     

Properties of a vector soliton laser passively mode-locked by a fiber-based semiconductor saturable absorber operating in transmission

We experimentally demonstrate a passively mode-locked fiber laser employing a fiber-based semiconductor saturable absorber (SSA) operating in transmission. Polarization rotation locked vector solitons are observed in the laser. Due to the intrinsic dynamic feature of the laser, period-doubling of these vector solitons has also been observed. Furthermore, extra spectral sidebands are formed on the optical spectrum, caused by the energy exchange between the two orthogonal polarization components of the vector solitons. By careful reduction of the pump power together with fine adjustment to the cavity birefringence, period-one state can further be obtained. Additionally, the phase noise properties of the vector soliton fiber laser have also been characterized experimentally and analytically.     

Structural,optical and electrical properties of undoped and Si-doped AlxGa1−xN thin films on Si (1 1 1) substrate grown by PA-MBE

We have studied the structural properties of undoped and Si-doped Al_xGa_1?xN/GaN/AlN on Si (1 1 1) substrate prepared by plasma-assisted molecular beam epitaxy (PA-MBE) using high-resolution X-ray diffraction (HR-XRD) and atomic force microscopy (AFM). In comparison with undoped AlGaN, the roughness and dislocation density on the surface of the AlGaN layer decrease with Si doping. Full width half maximum (FWHM) of the undoped and Si-doped samples were equal to 0.69° and 0.52°, respectively. This indicates that the Si doping improves the crystalline quality of the Al_xGa_1?xN layer compared with the undoped one. Raman scattering measurement reveals that the optical phonon modes of A₁(LO) and E₂(H) of the AlGaN show a one-mode and two-modes behavior, respectively. The Fourier-transform infrared reflectance (FTIR) investigation confirms the one-mode (two-mode) behavior of the LO (TO) phonon in our samples. This is in good agreement with Raman measurement. Finally, the barrier height (Φ_B) of undoped and Si-doped Al_xGa_1?xN samples was found to be 0.86 and 0.74 eV, respectively.     

(In, Mn)As nanowires with ultrahigh Mn concentration: Growth, morphology and magnetic anisotropy

(In,Mn)As nanowires with ultrahigh Mn concentration have been successfully grown on GaAs(001) substrates by molecular beam epitaxy. The morphology dependences on Mn concentration and growth temperature are investigated. High Mn concentration and high growth temperature are both necessary for the growth of nanowires. All the (In,Mn)As nanowires are self-aligned along [−110]GaAs, and therefore have the shape magnetic anisotropy with the easy axis along the alignment orientation of the nanowires.     

An efficient curvilinear non‐hydrostatic model for simulating surface water waves

An efficient curvilinear non‐hydrostatic free surface model is developed to simulate surface water waves in horizontally curved boundaries. The generalized curvilinear governing equations are solved by a fractional step method on a rectangular transformed domain. Of importance is to employ a higher order (either quadratic or cubic spline function) integral method for the top‐layer non‐hydrostatic pressure under a staggered grid framework. Model accuracy and efficiency, in terms of required vertical layers, are critically examined on a linear progressive wave case. The model is then applied to simulate waves propagating in a canal with variable widths, cnoidal wave runup around a circular cylinder, and three‐dimensional wave transformation in a circular channel. Overall the results show that the curvilinear non‐hydrostatic model using a few, e.g. 2–4, vertical layers is capable of simulating wave dispersion, diffraction, and reflection due to curved sidewalls. Copyright © 2010 John Wiley & Sons, Ltd.     

Improving imprinted shape cavities of molecularly imprinted sol–gel host matrix with minimal relaxation for sensing of creatinine

Journal of Sol-Gel Science and Technology - Molecularly imprinted polymer (MIP) is of great attention in biomimetic recognition systems due to its selective molecular recognition towards any guest...     

Compatible and tearing properties of poly(lactic acid)/poly(ethylene glutaric‐co‐terephthalate) copolyester blends

Fourier transform infrared and nuclear magnetic resonance results suggest that the carboxylic acid groups of poly(lactic acid) (PLA) molecules react with the hydroxyl groups of FePol (FP) molecules during the melt‐blending of PLA_xFP_y specimens. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) experiments of PLA and PLA/FP specimens suggest that only small amounts of poor PLA and/or FP crystals are present in their corresponding melt crystallized specimens. In fact, the percentage crystallinity, peak melting temperature, and onset re‐crystallization temperature values of PLA/FP specimens reduce gradually as their FP contents increase. However, the glass transition temperatures of PLA molecules found by DSC and DMA reduce to a minimum value as the FP contents of PLA_xFP_y specimens reach 6 wt %. Further DMA and morphological analysis of PLA/FP specimens reveal that FP molecules are compatible with PLA molecules at FP contents equal to or less than 6 wt %, as no distinguished phase‐separated FP droplets and tan δ transitions were found on fracture surfaces and tan δ curves of PLA/FP specimens, respectively. In contrast to PLA, the FP specimen exhibits highly deformable and tearing properties. After blending proper amounts of FP in PLA, the inherent brittle deformation and poor tearing behavior of PLA were successfully improved. Possible reasons accounting for these interesting crystallization, compatible and tearing properties of PLA/FP specimens are proposed. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 913–920, 2010     

Effects of the acceptor conjugation length and composition on the electrical memory characteristics of random copolyimides

Resistive‐switching memories based on copolyimides (coPIs), PI‐NTCDIX and PI‐BTCDIX , with different compositions of 4,4′‐diamino‐4″‐methyltriphenylamine ( AMTPA ), 4,4′‐(hexafluoroisopropylidene)diphthalic anhydride, and N,N′‐bis‐(4‐aminophenyl)‐1,8:4,5‐naphthalenetetracarboxydiimide ( NTCDI ) or N,N′‐bis‐(4‐aminophenyl)‐1,2:4,5‐benzenetetracarboxydiimide ( BTCDI ) have been developed. By varying the feed ratio of monomers, PI‐NTCDIX and PI‐BTCDIX showed tunable optical and electronic properties through the charge transfer (CT) between AMTPA and NTCDI or BTCDI . The memory devices based on PI‐NTCDIX exhibited the tunable electrical bistability from the volatile dynamic random access memory to nonvolatile write once read many memory characteristics as the NTCDI composition increased. The OFF/ON electrical switching transition was mainly attributed to the CT mechanism for the charge separated high conductance, based on the analysis of model compounds and density functional theory calculation. Also, the volatility of the memory device depended on the stability of CT complex. The long conjugation and high electron affinity of the NTCDI moiety stabilized the radical anion generated in the CT complex and prevented the recombination of segregated radical species even through applying the high positive or negative voltage. On the other hand, the memory devices based on PI‐BTCDIX showed a rather unique behavior compared with those based on PI‐NTCDIX . At the low BTCDI composition, the device exhibited volatile memory property. However, no switching behavior was observed at the high BTCDI composition due to the low highest occupied molecular orbital energy level of BTCDI . Combining these results and our previous study on perylenebisimide ( PBI ), we concluded that memory characteristics could be tailored by changing the conjugation length ( PBI > NTCDI > BTCDI ) and the acceptor composition in random coPIs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Surface‐initiated atom transfer radical polymerization from porous poly(tetrafluoroethylene) membranes using the C?F groups as initiators

This work reports the surface‐initiated atom transfer radical polymerization (ATRP) from hydrogen plasma‐treated porous poly(tetrafluoroethylene) (PTFE) membranes using the C? F groups as initiators. Hydrogen plasma treatment on PTFE membrane surfaces changes their chemical environment through defluorination and hydrogenation reactions. With the hydrogen plasma treatment, the C? F groups of the modified PTFE membrane surface become effective initiators of ATRP. Surface‐initiated ATRP of poly(ethylene glycol) methacrylate (PEGMA) is carried out to graft PPEGMA chains to PTFE membrane surfaces. The chain lengths of poly(PEGMA) (PPEGMA) grafted on PTFE surfaces increase with increasing the reaction time of ATRP. Furthermore, the chain ends of PPEGMA grown on PTFE membrane surfaces then serve as macroinitiators for the ATRP of N‐isopropylacrylamide (NIPAAm) to build up the PPEGMA‐b‐PNIPAAm block copolymer chains on the PTFE membrane surfaces. The chemical structures of the modified PTFE membranes are characterized using X‐ray photoelectron spectroscopy. The modification increases the surface hydrophilicity of the PTFE membranes with reductions in their water‐contact angles from 120° to 60°. The modified PTFE membranes also show temperature‐responsive properties and protein repulsion features owing to the presence of PNIPAAM and PPEGMA chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2076–2083, 2010