Comparison of quantitative methods for analysis of polyphasic pharmaceuticals

Adequate very sensitive quantification methods are needed for the development and are also now required for the monitoring of undesirable solid form(s) as routine tests. The pre-requisite for quantitation are selectivity, sensitivity and most important the purity of standards and their proper storage, what is a challenge for metastable forms. Several analytical techniques are available such as X-ray diffraction, spectroscopy, thermal analysis and microcalorimetry. The different steps of the validation of the analytical methods and problems to be solved are discussed. Examples illustrate the different techniques and compare their possible advantages and limits. The relative standard deviation of measurements should allow for checking the homogenization procedure of mixtures for calibration. The validation should be carried out following ICH guidelines for validation of analytical methods. Comparison of different techniques in adequate concentration range add confidence in the analytical results.     

Temperature influence on hydrogen sorption in palladium limited-volume electrodes (Pd-LVE)

The effect of temperature on hydrogen and deuterium electrosorption into a palladium LVE (limited-volume electrode) has been investigated. A decrease in hydrogen capacity (H/Pd ratio) with increasing temperature has been observed. Temperature strongly influences the plots of measured H(D)/Pd values vs. potential scan rate. In addition, hydrogen absorption was found to be dependent on the composition of the surrounding electrolyte solution. These results have confirmed the hypothesis that two different mechanisms of hydrogen desorption from the palladium electrode take place, namely electrochemical oxidation and non-electrochemical recombination. Further, the ratio between the rate constants for these two processes has been found to change with temperature. Electronic Publication     

Kinetics of thermal decomposition of alkaline phosphates

Summary The thermal behavior of KH₂PO₄, NaH₂PO₄ and Na₂HPO₄ under non-isothermal conditions using TG method with different heating rates was studied. The values of the reaction rate were processed by means of Friedmans differential-isoconversional method. A dependence of the activation energy vs. conversion was observed. Therefore a procedure based on the compensation effect (suggested by Budrugeac and Segal) was applied. A less speculative data processing protocol was offered by the non-parametric kinetics method suggested by Serra, Nomen and Sempere. Three steps were observed by non-isothermal heating: a dehydration, a dimerization and a polycondensation. The differences in the intimate reaction mechanism are determined by the initial number of water molecules.     

Interaction of gas phase atomic hydrogen with Pt(111):Direct evidence for the formation of bulk hydrogen species

Employing hot tungsten filament to thermal dissociate molecular hydrogen,we generated gas phase atomic hydrogen under ultra-high vacuum(UHV)conditions and investigated its interaction with Pt(111) surface.Thermal desorption spectroscopy(TDS)results demonstrate that adsorption of molecular hy- drogen on Pt(111)forms surface Had species whereas adsorption of atomic hydrogen forms not only surface Had species but also bulk Had species.Bulk Had species is more thermal-unstable than surface Had species on Pt(111),suggesting that bulk Had species is more energetic.This kind of weakly- adsorbed bulk Had species might be the active hydrogen species in the Pt-catalyzed hydrogenation reactions.     

Surface tension measurements in the study of molecular complexes

Surface tension measurements can be used to investigate molecular complex formation in liquid solutions for strong and weak complexes. The association constant and epthalpy for triethylamine-iodine, hexamethylbenzene-tetracyanoethylene and ethanol-iodine in cyclohexane are 4·55×10³, 218 and 0.93M⁻¹ at 25° C and 12·5, 7·7 and 5·1 kcal/mol respectively. These values compare well with those reported in the literature by other methods.     

An Easy One-Pot Procedure for the Synthesis of <Emphasis Type="Italic">N</Emphasis>-Sulfonyl Phosphorous Ylides and Sulfonyl Iminophosphoranes

Summary. Reaction of triphenylphosphine and an electron deficient acetylenic ester in the presence of strong N–H acid such as alkyl and aryl sulfamides or acetamide produces phosphorous ylides at room temperature in CH₂Cl₂. The aryl sulfamide phosphoranes undergo a smooth transformation reaction in boiling toluene and produce iminophosphoranes.     

Assessment of Four Inter-Comparison Exercises in Organic Elemental Analysis

 Four inter-comparison exercises on organic elemental analysis were carried out between 1997 and 2001 by the Department of Analytical Chemistry of the University of Barcelona, together with the Microanalysis Service and the Institute of the Marine Sciences, which both belong to the CSIC in Barcelona, and the University of A Coru?a. More than sixty laboratories participated in these exercises. Here we describe the design and characteristics of the trials, the samples and the homogeneity tests applied. We report the results obtained for the analysis of carbon, hydrogen, nitrogen, sulphur and oxygen, their statistical analysis, and the most relevant aspects of the technical discussion meetings. Received December 20, 2001; accepted March 18, 2002; published online July 22, 2002     

Host-guest complexes of crown ethers with HN-proton-donor molecules

Crown ethers were reacted with HN-proton-donor molecules to obtain crystalline molecular host-guest complexes. It was found that complexes with crown ethers of different structure are formed, depending on the linear dimensions and mode of steric shielding of active centers of the proton-donor molecules.Translated from Zhurnal Obshchei Khimii, Vol. 74, No. 12, 2004, pp. 2030–2033.Original Russian Text Copyright © 2004 by Wang, Ganin.This revised version was published online in April 2005 with a corrected cover date.     

Molecular Beam Mass Spectrometry System for Characterization of Thermal Plasma Chemical Vapor Deposition

A molecular beam mass spectrometry system for in situ measurement of the concentration of gas phase species including radicals impinging on a substrate during thermal plasma chemical vapor deposition (TPCVD) has been designed and constructed. Dynamically controlled substrate temperature was achieved using a variable thermal contact resistance method via a backside flow of an argon/helium mixture. A high quality molecular beam with beamtobackground signal greater than 20 was obtained under film growth conditions by sampling through a small nozzle (75 m) in the center of the substrate. Mass discrimination effects were accounted for in order to quantify the species measurements. We demonstrate that this system has a minimum detection limit of under 100 ppb. Quantitative measurements of hydrocarbon species (H, H₂, C, CH₃, CH₄, C₂H₂, C₂H₄) using Ar/H₂/CH₄ mixtures and silicon species (Si, SiH, SiH₂, SiCl, SiCl₂, Cl, HCl) using Ar/H₂/SiCl₄ mixtures were obtained under thermal plasma chemical vapor deposition conditions.     

Polystyrene/thermoplastic starch blends with different plasticizers

Conventional plastics has a large impact in increasing the environment’s pollution. That’s why the interest has turned towards novel partially and completely biodegradable polymers. In this work, blends of polystyrene and thermoplastic starch with glycerol and Buriti (Mauritia flexuosa L.) oil as plasticizers were prepared. Samples were analyzed using TG/DTG and DSC techniques. The TG results indicated that the blends with Buriti oil are thermally more stable than those with glycerol. The DSC analysis that Buriti oil provides a higher degree of plasticization of PS, compared to the blends plasticized using glycerol under the studied conditions.