Electrochemical synthesis of ammonia based on doped-ceria-carbonate composite electrolyte and perovskite cathode

Electrochemical synthesis of ammonia was investigated using a cobalt-free La_0.6Sr_0.4Fe_0.8Cu_0.2O_3-δ-Ce_0.8Sm_0.2O_2-δ (LSFCu-SDC) composite cathode and SDC-ternary carbonate composite electrolyte. La_0.6Sr_0.4Fe_0.8Cu_0.2O_3-δ and Ce_0.8Sm_0.2O_2-δ were prepared via combined EDTA-citrate complexing sol-gel and glycine nitrate processes, respectively, and characterised by X-ray diffraction (XRD). Ammonia was successfully synthesised from wet hydrogen and dry nitrogen under atmospheric pressure using Ni-SDC, SDC-carbonate and LSFCu-SDC composites as anode, electrolyte and cathode respectively. Ammonia formation was observed at 400, 425, 450 and 475 °C and the maximum rate of ammonia production was found to be 5.39 × 10⁻⁹ mol s⁻¹ cm⁻² at 450 °C and 0.8 V. The AC impedance measurements were recorded before and after the ammonia synthesis in the range of temperature 400-475 °C. The formation of ammonia at the N₂ side together with stable current at 450 °C under constant voltage demonstrates that SDC-(Li/Na/K)₂CO₃ composite electrolyte exhibits significant proton conduction at a temperature around 450 °C.     

Improvement of the magnetic properties of barium hexaferrite nanopowders using modified co-precipitation method

Barium hexaferrite BaFe₁₂O₁₉ powders have been synthesized using the modified co-precipitation method. Modification was performed via the ultrasonication of the precipitated precursors at room temperature for 1 h and the additions of the 2% KNO₃, surface active agents and oxalic acid. The results revealed that single phase magnetic barium hexaferrite was formed at a low annealing temperature of 800 °C for 2 h with the Fe³⁺/Ba²⁺ molar ratio 8. The microstructure of the powders appeared as a homogeneous hexagonal platelet-like structure using 2% KNO₃ as the crystal modifier. A saturation magnetization (60.4 emu/g) was achieved for the BaFe₁₂O₁₉ phase formed at 1000 °C for 2 h with Fe³⁺/Ba²⁺ molar ratio 8 using 5 M NaOH solution at pH 10 in the presence of 2% KNO₃. Moreover, the saturation magnetization was 52.2 emu/g for the precipitated precursor at Fe³⁺/Ba²⁺ molar ratio 12 in was achieved for the precipitated precursor ultrasonicated for 1 h and then annealed at 1200 °C for 2 h. Coercivities from 956.9 to 4558 Oe were obtained at different synthesis conditions.     

Assessment of pulmonary artery stiffness using velocity-encoding magnetic resonance imaging: evaluation of techniques

The loss of pulmonary artery (PA) compliance has significant pathophysiological effect on the right ventricle. Noninvasive and reliable assessment of PA wall stiffness would be an essential determiner of right heart load and a clinically useful factor to assess cardiovascular risk. Two MRI techniques have been proposed for assessing PA stiffness by measuring pulse wave velocity (PWV): transit time (TT) and flow area (QA). However, no data are available that compares the two techniques and evaluates their performance, especially over a wide range of PWV values or at 3.0-T, which is the purpose of the present study. Thirty-three patients with different heart conditions were imaged using optimized high-temporal resolution and high-spatial resolution velocity-encoding MRI sequences. Statistical analysis was conducted to study intermethod, interobserver and intraobserver variabilities. The PWV measurements using TT and QA techniques showed good agreement (P>0.1). The Bland-Altman analysis showed negligible differences between the two methods (mean±S.D.=0.11±0.35 m/s, correlation coefficient r=0.94). The repeated measurements showed low interobserver and intraobserver variabilities, although the S.D. of the differences was larger in the QA technique. The mean±S.D. of the TT/QA measurement differences were −0.05±0.2/0.0±0.36 m/s and 0.02±0.26/0.02±0.39 m/s for the interobserver and intraobserver differences, respectively. In conclusion, each technique has its own advantages and disadvantages. The two techniques result in similar measurements, although the QA method is more subjective due to its dependency on operator intervention.     

Metal adsorption of gamma-irradiated carboxymethyl cellulose/polyethylene oxide blend films

Blend films of different ratios of carboxymethyl cellulose (CMC)/polyethylene oxide (PEO) were prepared by the solution casting method. To investigate the effect of irradiation on all properties of prepared blend, it was exposed to different gamma irradiation doses (10, 20, and 30?kGy). Physical properties such as gel fraction (GF) (%) and swelling (SW) (%) were investigated. It was found that the GF (%) increases with increasing irradiation dose up to 20?kGy, while SW (%) decreases with an increase in the irradiation doses for all blend compositions. Moreover, the structural and mechanical properties of the prepared films were studied. The results of the mechanical properties obtained showed that there is an improvement in these properties with an increase in both CMC and irradiation dose up to 20?kGy. The efficiency of metal ions uptake was measured using a UV spectrophotometer. The prepared films showed good tendency to absorb and release metal ions from aqueous media. Thus, the CMC/PEO film can be used in agricultural domain.     

A highly sensitive and specific polyclonal antibody-based enzyme immunoassay for therapeutic monitoring and pharmacokinetic studies of atorvastatin

This study describes the development and validation of a highly sensitive and specific enzyme immunoassay (EIA) for therapeutic monitoring and pharmacokinetic studies of atorvastatin (ATR). The assay employs a polyclonal antibody that recognizes ATR with high specificity and affinity, and ATR conjugated to bovine serum albumin (ATR-BSA) immobilized onto microwell plates as a solid phase. The assay involved a competitive binding reaction between ATR and the immobilized ATR-BSA for the binding sites on a limiting amount of the anti-ATR antibody. The bound anti-ATR antibody was quantified with horseradish peroxidase-labeled anti-immunoglobulin secondary antibody and 3,3′,5,5′-tetramethylbenzidine as a substrate for the peroxidase enzyme. The concentration of ATR in the sample was quantified by its ability to inhibit the binding of the anti-ATR antibody to the immobilized ATR-BSA and subsequent color development in the assay wells. The conditions for the EIA were investigated and optimized for the determination of ATR in plasma samples. The limit of detection was 0.04 ng mL^?1 and the effective working range at relative standard deviations (RSD) of ≤5% was 0.1–10 ng mL^?1. Mean analytical recovery of ATR from spiked plasma was 99.3?±?2.8%. The precision of the assay was satisfactory; RSD were 2.7–4.6 and 3.3–5.7% for intra- and inter-assay precision, respectively. The reliability of the EIA was confirmed by HPLC. The EIA is convenient, and one can analyze ～ 200 samples per working day, facilitating the processing of large-number of samples of ATR.     

DSC study of the kinetic parameters of the metastable phases formation during non-isothermal annealing of an Al–Si–Mg alloy

Kinetics of β″ and β′ precipitations in an AlSiMg have been studied under non-isothermal conditions using differential scanning calorimetry (DSC) technique. The variation of the activation energy as a function of transformed fraction is determined using two isoconversional methods of Kissinger–Akahira–Sunose (KAS) and Friedman. The results obtained using the two methods show a change in the activation energy for both metastable phases precipitations as a function of transformed fraction. The results obtained from KAS method as compared with those obtained from Friedman method, show some major disagreements between the two methods. The growth exponent, determined by Ozawa method, decreases as a function of temperature for both phases.