某轴流压气机叶尖间隙效应实验研究

本文对某低速轴流压气机叶尖间隙尺度对性能的影响进行了实验研究,并通过不同的机匣结构情况研究一种叶尖漏流不敏感机匣。实验表明,不同的间隙尺度对叶轮机总体性能存在十分明显的影响。对绝大部分运行状态,小间隙下的压升和效率均明显高于大间隙的情况。另外,所采用的毛刷式和篦齿式的机匣实验结果表明,不论毛刷式还是篦齿式机匣,在大流量负攻角情况下对性能的影响不大,但毛刷式机匣并不能达到提高失速裕度的目的,而篦齿式机匣在小流量情况下对压升有所提高,但对效率影响不大。     

斐索梯度折射率光纤透镜传感实验

采用LD泵浦的单纵模Nd：YVO4倍频激光器、梯度折射率光纤透镜等器件构成斐索梯度折射率光纤透镜传感实验仪．本文介绍了实验装置和实验原理，并给出了实验结果。     

Writing Fiber Grating of Different Wavelength Using the Same Phase Mask

Chirped fiber grating was used in dispersion compensator. We tried to use the same phase mask to write fiber grating of different wavelength with two methods to reduce the price of the fiber grating.     

基于新型长周期光纤光栅的掺铒光纤放大器

报道了基于高频CO₂激光脉冲写入的新型长周期光纤光栅的低噪音掺铒光纤放大器,这种新型长周期光纤光栅是用大约几千Hz的高频CO₂激光脉冲对光纤玻璃热冲击作用而形成的.在铒纤中插入一个长周期光纤光栅,会明显减少掺铒光纤放大器的放大自发辐射(ASE)噪音.报道了两种低噪音掺铒光纤放大器,作为前置放大器和线路放大器,它们的ASE噪音指数分别从4.0 dB减少到3.5 dB和从4.8 dB减少到4.3 dB,并且在作为线放时,其小信号增益从30 dB提高到37 dB,降噪及提高增益效应十分显著.     

Hydrothermal Synthesis and Structure of [（PbCl2）μ-PyZ）1/2]n （Pyz = Pyrazine）

1 INTRODUCTION Because of the flexibility of Pb(II) coordination sphere and the nonstereospecific nature of halide anions[1], the chemistry of lead halide complexes has been developed in recent years. Especially PbX2- based coordination polymers with nitrogen-contain- ing Lewis bases have attracted renewed interest[2～11]. The choice of ligand and the reaction condition are of great importance in determining the final topo- logy of the supramolecular materials. But the avail- able struc…     

Covalent functionalization of multi-walled carbon nanotubes by lipase

Lipase from Candida rugosa was covalently anchored onto acid-treated multi-walled carbon nanotubes (MWNTs) through a self-catalytic mechanism. A variety of characterization techniques including FTIR, Raman spectroscopy, and XPS were employed to demonstrate the formation of the ester linkage between lipase and MWNTs. The MWNTs-lipase biocomposites showed significantly increased solubility in some common-used organic solvents, such as THF, DMF and chloroform. This study may offer a novel and facile route for covalent modification of carbon nanotubes, and expand the potential utilization of both lipases and MWNTs in the fields of biocatalyst and biosensor.     

Specific heat and related thermophysical properties of liquid Fe-Cu-Mo alloy

The specific heat and related thermophysical properties of liquid Fe77.5Cu13Mo9.5 monotectic alloy were investigated by an electromagnetic levitation drop calorimeter over a wide temperature range from 1482 to 1818 K. A maximum undercooling of 221 K (0.13 Tm) was achieved and the specific heat was determined as 44.71 J·mol-1·K-1. The excess specific heat, enthalpy change, entropy change and Gibbs free energy difference of this alloy were calculated on the basis of experimental results. It was found that the calculated results by traditional estimating methods can only describe the solidification process under low undercooling conditions. Only the experimental results can reflect the reality under high undercooling conditions. Meanwhile, the thermal diffusivity, thermal conductivity, and sound speed were derived from the present experimental results. Furthermore, the solidified microstructural morphology was examined, which consists of (Fe) and (Cu) phases. The calculated interface energy was applied to exploring the correlation between competitive nucleation and solidification microstructure within monotectic alloy.     

Thermal conductance for single wall carbon nanotubes

We report a theoretical analysis of the phonon thermal conductance, κ(T), for single wall carbon nanotubes (SWCN). In a range of low temperatues up to 100 K, κ(T) of perfect SWCN is found to increase with temperature, approximately, in a parabolic fashion. This is qualitatively consistent with recent experimental measurements where the tube-tube interactions are negligibly weak. When the carbon-carbon bond length is slightly varied, κ(T) is found to be qualitatively unaltered which implies that the anharmonic effect does not change the qualitative behavior of κ(T). Received 12 June 2001     

类型γ射线能谱指纹的识别机理

放射源的辐射指纹能起到标识和鉴别放射性物体的作用.在涉及核弹头不可逆销毁过程的深度核裁军核查中,核弹头的辐射指纹对标识和鉴别裁减下来的核弹头将起到关键作用.预先研究辐射指纹的有关技术,如识别机理的研究,将有助于深度核裁军的核弹头核查技术发展.以实验室放射源为研究对象,探索了类型γ射线能谱指纹的同一性识别机理.类型γ射线指纹识别机理的研究,就是要找出一种合适的方法,以较高的置信度,描述两个正在进行比较的γ射线指纹是否为同一放射源的指纹.采用了谱形比较法,并用谱相似度概念来描述两个指纹的相似程度.在谱形比较思想的指导下,编制了放射源类型指纹识别软件,并通过放射源同一性的识别实验验证了软件的有效性,同时研究了谱相似度随统计涨落和测量条件,如时间、源强和本底等因素的变化情况.研究结果表明:1)用相似度概念来描述两个指纹的相似程度,回答两个待比较的γ射线能谱是否代表同一类型放射源,是切实可行的;2)该识别机理只具备识别放射源类型的能力,而对同一类型、差异甚微的放射源个体还不能识别 关键词： γ射线能谱指纹 辐射指纹 识别机理 核查技术