辐射加热金X光再发射时间测量

利用星光Ⅱ三倍频激光打双盘靶，研究了辐射加热材料的Ｘ光发射时间。激光脉冲能量４０～６０Ｊ、脉冲宽度６００～７００ｐｓ。通过两台时间关联的亚千Ｘ光能谱仪分别监测双盘靶初、次级发射Ｘ光谱，给出了辐射加热次级Ｘ光再发射时间。     

基于ZBLANⅩⅣPr,Yb频率上转换发光的三维立体显示

本文对利用ZBLANⅩⅣPr,Yb频率上转换发光的三维立体显示做了研究,探讨了其中的一些物理问题.在实验中,我们利用Yb³⁺离子敏化的方法提高Pr³⁺的上转换发光效率;通过降低能引起单频上转换发光的激光强度来提高寻址点和非寻址点在显示过程中的对比度.     

折射率温敏式光纤温度传感器的理论模型

提出了折射率温敏式光纤温度传感器的理论模型，包括子午光线和偏射光线的影响，讨论了多模光纤的弯曲损耗，理论的分析和结果与实验相当一致。     

The magnetic entropy changes in Gd1−xBx alloys

A series of Gd_(1−x)B_x alloys have been prepared by arc melting method. After introducing small quantity of B atom in Gd, the Curie temperature of these alloys increase while the magnetic entropy changes are almost same as that of Gd. The refrigerant capacities of these alloys are also greater than that of Gd. These results suggest that Gd_(1−x)B_x alloys may be utilized as refrigerant in household magnetic refrigeration.     

The optical properties of planar waveguides in LiB3O5 crystals formed by Cu implantation

A planar optical waveguide has been formed in a LiB₃O₅ crystal using 6.0 MeV Cu⁺-ions with a dose of 1 × 10¹⁵ ions/cm² at room temperature. Possible propagating modes were measured at a wavelength of 633 nm using the prism-coupling method. The refractive index profiles of the waveguide were reconstructed by an effective refractive index method and the beam propagation method was used to investigate the properties of the propagation modes in the formed waveguide. The results suggest that the fundamental TE₀ and TM₀ modes may be well-confined and propagate a longer distance inside the waveguide. The implantation process was also simulated using the transport of ions in matter code (TRIM), which indicates that the nuclear energy deposition may be the main factor for the refractive index change.     

BRD96N光调制吸收增强现象的实验研究

通过光谱响应特性实验和记录／读出图像实验，研究了基因变异型细菌视紫红质（BR_D96N）分子膜对单色光的光调制特性.发现BR_D96N分子膜在550nm—600nm范围内对调制光有吸收增强的现象，且对此范围内不同波长的单色光其调制程度有差异.利用曲线拟和方法发现550nm—600nm吸收增强的变化过程分为快过程和慢过程，其对应的时间常数分别为30s和5min.利用强度调制器的吸收强度与图像灰度之间的关系，分析了560nm—600nm范围内出现图像反转的实验现象. 关键词： 细菌视紫红质D96N分子膜 光谱响应 吸收增强现象 图像反转现象     

Effect of the dispersibility of ZrO2 nanoparticles in Ni-ZrO2 electroplated nanocomposite coatings on the mechanical properties of nanocomposite coatings

ZrO₂ nanoparticles was uniformly co-deposited into a nickel matrix by electroplating of nickel from a Watts bath containing particles in suspension which were monodispersed with dispersant under DC electrodeposition condition. It was found that morphology, orientation and hardness of the nanocomposite coatings with monodispersed ZrO₂ nanoparticles had lots of difference from the nanocomposite coatings with agglomerated ZrO₂ nanoparticles and pure nickel coatings. Especially, the result of hardness showed that only a very low volume percent (less than 1 wt.%) of monodispered ZrO₂ nanoparticles in Ni-ZrO₂ nanocomposite coatings would result in higher hardness of the coatings. The hardness of Ni-ZrO₂ nanocomposite coatings with monodispersed and agglomerated ZrO₂ nanoparticles were 529 and 393 HV, respectively. The hardness value of the former composite coatings was over 1.3 times higher than that of the later. All these composite coatings were two-three times higher than that of pure nickel plating (207 HV) prepared under the same condition. The strengthening mechanisms of the Ni-ZrO₂ nanocomposite coatings based on a combination of grain refinement strengthening from nickel matrix grain refining and dispersion strengthening from dispersion state of ZrO₂ nanoparticles in the coatings.