In-Situ Intrinsic Interface Strength Measurement at Elevated Temperatures and its Relationship to Interfacial Structure

A previously developed laser spallation technique has been modified to measure the tensile strength of thin film interfaces in-situ at temperatures up to 1100°C. Tensile strengths of Nb/A-plane sapphire, FeCrAl/A-plane sapphire and FeCrAlY/A-plane sapphire were measured up to 950°C. The measured strengths at high temperatures were substantially lower compared with their corresponding strengths at ambient temperature. For example, at 850°C, the interface tensile strength for the Nb/sapphire (151 ± 17 MPa), FeCrAl/sapphire (62 ± 8 MPa) and FeCrAlY/sapphire (82 ± 11 MPa) interface systems were lower by factors of approximately, 3, 5, and 8, respectively, over their corresponding ambient values. These results underscore the importance of using such in-situ measured values under operating conditions as the failure criterion in any life prediction or reliability models of such coated systems where local interface temperature excursions are expected. The results on alloy film interfaces also demonstrate that the presence of Y increases the strength of FeCrAl/Al₂O₃ interfaces.     

70K温区混合工质分凝分离循环节流制冷机实验研究

混合工质节流制冷机正在许多方面获得越来越广泛的应用。文中设计了一种新型的混合工质分凝分离循环 ,建立了实验系统 ,并在 70 K温区进行了实验。实验结果表明 ,节流制冷机可以达到 6 5 .3K的低温 ,并在 72 K温度提供 1W的制冷量 ,输入功率为 5 0 0 W。     

Giant Magneto-Impedance of Co50Ni22Ga28 Alloy with High Chemical Ordering

The microstructure of CosoNi22Ga28 ribbon with the L10 structure is examined. The band-like morphology is observed. These bands with the width in a range of 40-200 nm appear along the transverse direction of the ribbon. The giant magnetoimpedance （GMI） effect in this alloy is measured. The results show that Co5oNi22Ga28 exhibits a sharp peak of the GAI effect. The maximum GAH ratio up to 360% is detected. The GMI effect measured versus temperature shows large jumps of the magnetoimpedance amplitude at the reversal martensitic transformation temperature 240℃ and Curie temperature 375℃C respectively. The jump ratios of the magnetoimpedance amplitude examined at these temperatures are about 5 and 10, respectively.     

Experimental investigation and theoretical modeling of liquid entrainment in a horizontal tee with a vertical-up branch

This article describes a comprehensive literature review of liquid entrainment in horizontal pipes with vertical-up branches. Deficiencies in the available data and correlations were identified. The Air–water Test Loop for Advanced Thermal–hydraulic Studies (ATLATS) was constructed and entrainment onset and steady-state data were collected for a wide range of flow conditions. Using new insights gained from experimental testing, the authors developed a model for predicting the onset of entrainment and steady-state entrainment rate. Previously published correlations, along with the new model, are compared against all available data. The new model shows very good agreement with the onset data, but is not very good at predicting branch quality at high liquid flow rates.     

Synthesis and structural characterization of novel,fluorinated poly(phthalazinone ether)s containing perfluorophenylene moieties

The synthesis and structural characterization of a series of novel, fluorinated poly(phthalazinone ether)s containing perfluorophenylene moieties are described. The monomers, 4‐(4′‐hydroxyaryl)phthalazin‐1(2H)‐ones ( 2a – 2d ), were conveniently and efficiently synthesized from phenols and phthalic anhydride in two steps via 2‐(4′‐hydroxybenzoyl)benzoic acids, which were first obtained by the Friedel–Crafts reaction in good yields and with high stereoselectivity and were then converted into 2a – 2d by fusion with hydrazine. All the polymers were prepared by nucleophilic aromatic substitution (S_NAr) polycondensation between the compounds perfluorobiphenyl and 4‐(4′‐hydroxyaryl)phthalazin‐1(2H)‐ones ( 2a ‐ 2d ). The resulting fluorinated polymers were readily soluble in common organic solvents (e.g., CHCl₃, tetrahydrofuran, dimethylformamide, dimethyl sulfoxide, N‐methylpyrrolidone, etc.) at room temperature. Their weight‐average molecular weights and the polydispersities ranged from (7.96–18.25) × 10³ to 1.31–2.71, respectively. Their glass‐transition temperatures varied from 213 to 263 °C. They were all stable up to 390 °C both in air and in argon. The 5% weight‐loss temperatures of these polymers in air and argon ranged from 393–487 to 437–509 °C, respectively. Wide‐angle X‐ray diffraction studies indicated they were all amorphous and could be attributed to the presence of kink nonplanar moiety, phenyl phthalazinone along the polymer backbone. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 925–932, 2004     

Combined effects of clay modifications and compatibilizers on the formation and physical properties of melt‐mixed polypropylene/clay nanocomposites

The melt mixing technique was used to prepare various polypropylene (PP)‐based (nano)composites. Two commercial organoclays (denoted 20A and 30B) served as the fillers for the PP matrix, and two different maleated (so‐called) compatibilizers (denoted PP‐MA and SMA) were employed as the third component. The results from X‐ray diffraction (XRD) and transmission electron microscope (TEM) experiments revealed that 190 °C was an adequate temperature for preparing the nanocomposites. Nanocomposites were achieved only if specific pairs of organoclay and compatibilizer were simultaneously incorporated in the PP matrix. For example, PP/20A(5 wt %)/PP‐MA(10 wt %) and PP/30B(5 wt %)/SMA(5 wt %) composites exhibited nanoscaled dispersion of 20A or 30B in the PP matrix. Differential scanning calorimetry (DSC) results indicated that the organoclays served as nucleation agents for the PP matrix. Generally, their nucleation effectiveness increased with the addition of compatibilizers. The thermal stability enhancement of PP after adding 20A was confirmed with thermogravimetric analysis (TGA). The enhancement became more evident as a suitable compatibilizer was further added. However, for the 30B‐included composites, thermal stability enhancement was not evident. The dynamic mechanical properties (i.e., storage modulus and loss modulus) of PP increased as the nanocomposites were formed; the properties increment corresponded to the organoclay dispersion status in the matrix. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4139–4150, 2004     

Preparation of benzoylchitosans and their chiroptical properties in dilute solutions

Two benzoyl substituted chitosan derivatives, 3,6‐O‐dibenzoylchitosan (DBC) and 2‐N‐3,6‐O‐tribenzoylchitosan (TBC), were prepared, and their optical activities in organic solvent were investigated by circular dichroism (CD). For TBC, two splitting bands (a negative one at 288 nm and a positive one at 274 nm) corresponding to the ¹L_b transition of the benzoyl group were observed in chloroform and dichloromethane, while only a negative CD band was recorded in N, N‐dimethylformamide (DMF). These results indicated that the transition moments of benzoyl groups were orderly arranged along the helical polymer chain when TBC was dissolved in a solvent with low polarity, but the same ordered structure did not appear in a polar solvent of DMF. For DBC, only negative CD signals corresponding to the ¹L_b transition of the benzoyl group were observed, regardless of the solvent property, which indicated that the chromophores were not arranged in an ordered fashion with appropriate geometry to interact with one another to induce bi‐signate CD signals. Adding methanol or DMF to the solution of TBC/chloroform resulted in a progressive decrease of the intensity of the positive split band at 274 nm. The intensity of the positive band was weakened upon heating a solution of TBC/chloroform from 20 to 60 °C. The results suggested that the ordered arrangement of the chromophores in the TBC system was dependent on solvent and sensitive to temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4107–4115, 2004     

Resonance-stabilized phenoxy-like radicals formed by NO-mediated mono-nitration of coumarins containing a hydroxy group

Stable aminoxyls and an iminoxyl were observed by spin trapping and EPR techniques during the nitration of coumarins containing a hydroxy group by nitric oxide. The trapped free radicals are deduced to be the resonance stabilized phenoxy-like radicals. The mechanisms for the nitrations are suggested.     

Cavitation mechanism in cyanobacterial growth inhibition by ultrasonic irradiation

To prevent cyanobacterial bloom in eutrophic water by ultrasonic method, ultrasonic irradiations with different parameters were tested to inhibit Spirulina platensis from growth. The experimental result based on cyanobacterial growth, chlorophyll a and photosynthetic activity showed that, the ultrasonic irradiation inhibited cyanobacterial proliferation effectively, furthermore the inhibition effectiveness increased in the order: 200 kHz>1.7 MHz>20 kHz and became saturated with the increased power. The inhibition mechanism can be mainly attributed to the mechanical damage to the cell structures caused by ultrasonic cavitation, which was confirmed by light microscopy and differential interference microscopy. The optimal frequency of 200 kHz in cavition and sonochemistry was also most effective in cyanobacterial growth inhibition. The higher frequency of 1.7 MHz is weaker than 20 kHz in cavitation, but has more effective inhibition because it is nearer to the resonance frequency of gas vesicle. The inhibition saturation with ultrasonic power was due to the ultrasonic attenuation induced by the acoustic shielding of bubbles enclosing the radiate surface of transducer.     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.