Experimental aspects of ultrasonically enhanced cross-flow membrane filtration of industrial wastewater

Ultrasound based on-line cleaning for membrane filtration of industrial wastewater was studied. An ultrasonic transducer was assembled in the membrane module in order to get an efficient cleaning of membranes in fouling conditions. The focus of the studies was on the effects of the ultrasound propagation direction and frequency as well as the transmembrane pressure. The more open the membrane was the easier the membrane became plugged by wastewater colloids, when the ultrasound propagation direction was from the feed flow side of the membrane. If the membrane was tight enough, the ultrasound irradiated from the feed side of the membrane increased the flux significantly. However, in the circumstances studied, the power intensity needed during filtration was so high that the membranes eroded gradually at some spots of the membrane surface. It was discovered that the ultrasonic field produced by the used transducers was uneven in pressurised conditions. On the other hand, the ultrasound treatment at atmospheric pressure during an intermission pause in filtration turned out to be an efficient and, at the same time, a gentle method in membrane cleaning. The input power of 120 W (power intensity of 1.1 W/cm2) for a few seconds was sufficient for cleaning. The flux improvement was significant when using a frequency of 27 kHz but only minor when using 200 kHz.     

A generalization of the Subbarao identity

Arithmetical functionsf andh are said to satisfy the Subbarao identity if

The determination of thickness and surface mass density of mesothick immunoprecipitate layers by null ellipsometry and protein 125iodine labeling

The aim of the present study was to ellipsometrically determine the thickness and surface mass density in air for up to 110-nm-thick organic layers made of alternatingly deposited layers of HSA and polyclonal anti-HSA on hydrophobic silicon. The ellipsometrically determined thickness was compared to that obtained by AFM and the deposited surface mass density calibrated with (125)I-labeled proteins. The results indicate a good agreement in protein layer thickness between AFM and ellipsometry when the protein film refractive index N(film)=1.5-0i, although then the calculated surface mass density from the ellipsometry data became grossly overestimated by the Cuypers one-component formula. A good agreement in the surface mass density was obtained when the M/A ratio in this formula was lowered from 4.14 to 2.35. This approach indicates a convenient means of determining the refractive indices and surface mass densities of mesothick organic layers proteins on solid supports.     

The prediction of mechanical properties of injection moulding parts by vacuum casting

The behaviour of vacuum cast prototypes and injection moulding parts in mechanical tests was compared. The mechanical tests were made using real production parts as references. Distinct correlations were found between vacuum cast prototypes and injection moulding parts. In this light, vacuum cast prototypes can be used for the evaluation of injection moulding products with certain limitations. Vacuum casting is best suited for the evaluation of such mechanical properties of injection moulding products as tensile, flexural and compression strength, while impact strength is the property that is most difficult to evaluate.     

Monitoring the precision of routine analyses by using duplicate determinations

To ensure the reliability of results, analytical laboratories require a continuous qualitycontrol program which must take account of both systematic and random errors. Analyses of reference materials can be used to estimate systematic errors but estimates of random errors (precision) tend to be optimistic, mainly because reference materials cannot be put through the whole analytical process (e.g., primary sampling is often a major source of error). Estimates of precision must be based on routine samples. If duplicate determinations are done on routine samples, the precision can be estimated reliably. Within the optimum concentration range of analytical method (usually starting from 5-10 times the detection limit), the relative standard deviation (s_r can be regarded as being almost constant or independent of concentration. The precision can then be estimated by first calculating the s_r value of each pair of results. Individually, these are not reliable estimates of the true s_r, but they can be regarded as independent measurements of the same s_r and so can be pooled to obtain a more reliable estimate of precision with the number of duplicates as the degrees of freedom. The applicabiilty of the method is tested on soil, rock and ore samples.     

Discarding or downweighting high-noise variables in factor analytic models

This work examines the factor analysis of matrices where the proportion of signal and noise is very different in different columns (variables). Such matrices often occur when measuring elemental concentrations in environmental samples. In the strongest variables, the error level may be a few percent. For the weakest variables, the data may consist almost entirely of noise. This paper demonstrates that the proper scaling of weak variables is critical. It is found that if a few weak variables are scaled to too high a weight in the analysis, the errors in computed factors would grow, possibly obscuring the weakest factor(s) by the increased noise level. The mathematical explanation of this phenomenon is explored by means of Givens rotations. It is shown that the customary form of principal component analysis (PCA), based on autoscaling the original data, is generally very ineffective because the scaling of weak variables becomes much too high. Practical advice is given for dealing with noisy data in both PCA and positive matrix factorization (PMF).     

The Prevalence of Voice Disorders Among Day Care Center Teachers Compared with Nurses: A Questionnaire and Clinical Study

The acceptance of voice disorders by day care center teachers as an occupational disease is not an invariably established practice. This is due to the lack of reliable evidence of a higher risk for voice disorders in this profession. To find out the risk of voice disorders, an epidemiological study was conducted among day care center teachers (n = 262), using hospital nurses (n = 108) as a control group. Symptoms were charted by a questionnaire. In a clinical examination made by a laryngologist, the voice quality was assessed and the laryngeal status noted. Teachers at day care centers had significantly more voice disorders than did nurses. Vocal nodules and laryngitis findings appeared significantly more frequently among day care center teachers than among those in the control group. The results prove voice disorders to be more frequent among day care center teachers than among control group subjects, and also that the main cause for this may be a higher vocal loading among day care center teachers than among control group subjects.     

Determination of the Glass Electrode Parameters by Means of Potentiometric Titration of Acetic Acid in Aqueous Sodium or Potassium Chloride Solutions at 25°C

Single-ion activity coefficient equations are presented for the calculation of stoichiometric (molality scale) dissociation constants K _m for acetic acid in aqueous NaCl or KCl solutions at 25°C. These equations are of the Pitzer or Hückel type and apply to the case where the inert electrolyte alone determines the ionic strength of the acetic acid solution considered. K _m for a certain ionic strength can be calculated from the thermodynamic dissociation constant K _a by means of the equations for ionic activity coefficients. The data used in the estimation of the parameters for the activity coefficient equations were taken from the literature. In these data were included results of measurements on galvanic cells without a liquid junction (i.e., on cells of the Harned type). Despite the theoretical difficulties associated with the single-ion activity coefficients, K _m can be calculated for acetic acid in NaCl or KCl solutions by the Pitzer or Hückel method (the two methods give practically identical K _m values) almost within experimental error at least up to ionic strengths of about 1 mol-kg^–1. Potentiometric acetic acid titrations with base solutions (NaOH or KOH) were performed in a glass electrode cell at constant ionic strengths adjusted by NaCl or KCl. These titrations were analyzed by equation E = E _o + k(RT/F) ln[m(H⁺)], where m(H⁺) is the molality of protons, and E is the electromotive force measured. m(H⁺) was calculated for each titration point from the volume of the base solution added by using the stoichiometric dissociation constant K _m obtained by the Pitzer or Hückel method. During each base titration at a constant ionic strength, E _o and k in this equation were observed to be constants and were determined by linear regression analysis. The use of this equation in the analysis of potentiometric glass electrode data represents an improvement when compared to the common methods in use for two reasons. No activity coefficients are needed and problems associated with liquid junction potentials have been eliminated.