Structural and Mössbauer studies of nanocrystalline Mn<Superscript>4+</Superscript>-doped Li<Subscript>0.5</Subscript>Fe<Subscript>2.5</Subscript>O<Subscript>4</Subscript> particles prepared by mechanical milling

The structure and magnetic properties of spinel-related Mn⁴⁺-doped Li_0.5Fe_2.5O₄ nanocrystalline particles of the composition Li_0.5Fe_2.25Mn_0.1875O₄, prepared by milling a pristine sample for different times, were investigated. The average crystallite and particle size, respectively, decreased form ～40 nm to ～10 nm and ～2.5 μm to ～10 nm with increasing milling time from 0 h to 70 h. Rietveld refinement of the XRD data of the non-milled sample show the Mn⁴⁺ dopant ions to substitute for Fe³⁺ at the octahedral B-sites of the spinel-related structure. The Mössbauer spectra of the milled ferrites indicate that more particles turn superparamagnetic with increasing milling time. The Mössbauer data collected at 78 K suggest that while in the non-milled sample the Mn⁴⁺ ions substitute for Fe³⁺ at the octahedral B-sites, this is reversed as milling proceeds with doped Mn⁴⁺ ions, balancing Fe³⁺ vacancies and possibly Li⁺ ions progressively migrate to the tetrahedral A-sites. This is supported by the slight increase observed in the magnetization of the milled samples relative to that of the non-milled one. The magnetic data suggest that in addition to the increasing superparamagentic component of the milled particles, thermal spin reversal and/or spin canting effects are possible at the surface layers of the nanoparticles.     

Nonradial large solutions of sublinear elliptic problems

Let p be a nonnegative locally bounded function on , N3, and 0<γ<1. Assuming that the oscillation sup_|x|=rp(x)−inf_|x|=rp(x) tends to zero as r→∞ at a specified rate, it is shown that the equation Δu=p(x)u^γ admits a positive solution in satisfying lim_|x|→∞u(x)=∞ if and only if

     

Application of Molecularly Imprinted Polymers in the Analysis of Waters and Wastewaters

The increase of the global population and shortage of renewable water resources urges the development of possible remedies to improve the quality and reusability of waste and contaminated water supplies. Different water pollutants, such as heavy metals, dyes, pesticides, endocrine disrupting compounds (EDCs), and pharmaceuticals, are produced through continuous technical and industrial developments that are emerging with the increasing population. Molecularly imprinted polymers (MIPs) represent a class of synthetic receptors that can be produced from different types of polymerization reactions between a target template and functional monomer(s), having functional groups specifically interacting with the template; such interactions can be tailored according to the purpose of designing the polymer and based on the nature of the target compounds. The removal of the template using suitable knocking out agents renders a recognition cavity that can specifically rebind to the target template which is the main mechanism of the applicability of MIPs in electrochemical sensors and as solid phase extraction sorbents. MIPs have unique properties in terms of stability, selectivity, and resistance to acids and bases besides being of low cost and simple to prepare; thus, they are excellent materials to be used for water analysis. The current review represents the different applications of MIPs in the past five years for the detection of different classes of water and wastewater contaminants and possible approaches for future applications.     

Evaluation of the Antimicrobial Effect of Thymoquinone against Different Dental Pathogens: An In Vitro Study

This study aimed to evaluate the antimicrobial effect of Thymoquinone (TQ) on four different oral microorganisms. Minimum Bactericidal Concentration (MBC), Minimum Inhibition Concentration (MIC), Broth microdilution, and Well diffusion tests were used to determine the optimum antimicrobial concentrations of TQ against Streptococcus salivarius, Streptococcus oralis, Streptococcus mutans, and Staphylococcus aureus over 1, 3, 6, 12 and 24 h. Chlorhexidine 0.12% was selected as a positive control. The inhibitory effect of TQ on bacterial growth was most noticeable with S. salivarius, while the least affected was S. aureus. TQ’s MBC and MIC for S. oralis and S. aureus were comparable 2 mg/mL and 3 mg/mL, respectively. S. salivarius was most resistant to TQ and displayed a value of 5 mg/mL and 4 mg/mL for MIC and MBC, respectively. The viable count of different strains after exposure to TQ’s MBC values was most noticeable with S. aureus followed by S. oralis and S. mutans, while S. salivarius was least affected. This study emphasized the promising antimicrobial effect of TQ against the four main oral microorganisms. It has a potential preventive effect against dental caries as well as other oral diseases.     

Investigation of lubricant induced pre-ignition and knocking combustion in an optical spark ignition engine

An experimental study was performed to investigate lubricant oil induced pre-ignition and knocking combustion process in a single cylinder spark ignition (SI) engine with full bore overhead optical access. Lubricant oil was deliberately injected to the exhaust area through a specially modified direct injector to trigger the stochastic pre-ignition in a premixed air and fuel mixture. Simultaneous heat release analysis and high speed combustion imaging were used to study the pre-ignition and combustion processes. Outlier detection based on robust statistical methods was validated as an effective and efficient approach to identify sporadic pre-ignition. When pre-ignition occurred, the pre-ignited flame-front exhibited much faster propagating speed than that of the normal spark-ignited flame-front in the first stage of flame development. In several cycles, pre-ignition was followed by the pre-ignited propagating flame-front and then a separate spark-ignited flame-front before they subsequently merged together. In a few other cycles, pre-ignition led to heavy knocking combustion caused either by the auto-ignition close to the flame-front or near the cylinder wall, or both. The ultimate knock intensity of such cycles was determined by the timing, size, and location of end-gas auto-ignition of the unburned gas. Furthermore, optical detection of the oil droplet entrained combustion in the cycle subsequent to the knocking combustion cycle implied that high frequency oscillation pressure waves ejected lubricant from the piston-ring crevice.     

Catalysis of the 〈b̄b〉 Condensate in the Composite Higgs Model

Increasing external pressure gives rise to s–d electron transfer in calcium that results in the localization of the charge density in the interstices of the crystal structure, i.e., the formation of an electride. The corresponding electronic states are partially filled and localized and, hence, electronic correlations could arise. We have carried out theoretical calculations for the high-pressure phases of Ca taking into account the Coulomb interactions between the electronic states centered on the interstitial site. The results of our calculations and proposed microscopic model showed that the structural phase transition under high pressure is due to an interplay of hybridization and correlation effects. Furthermore, it was found that the Coulomb repulsion can explain the experimentally observed anomalous increase in resistivity of the simple cubic phase of calcium under pressure.

     

Improvement of photoluminescence and electrical properties of porous silicon layer treated with lanthanum

The influence of surface treatment of porous silicon (PS) in lanthanum (La) containing solution during different times on its photoluminescence and electrical properties has been investigated. For this purpose, chemical composition, structural, vibrational, photoluminescence and electrical characteristics of the porous silicon layer with and without lanthanum were examined using X-ray diffractometry (XRD), energy dispersive X-ray (EDX) spectroscopy, Fourier transmission infrared (FTIR) spectroscopy, photoluminescence (PL) spectroscopy and current–voltage (I–V) measurements. The results indicate that porous silicon layers treated with lanthanum exhibit an enhancement of photoluminescence intensity and show an improvement current intensity compared to untreated porous silicon layer.     

Timed Petri nets and prediction to improve the Chandy–Misra conservative-distributed simulation

The main contribution of this paper shows that distributed simulation of timed Petri nets (TPN) can take advantage of their structure to obtain a significant lookahead which is usually difficult to compute with other models. In this paper, we introduce a conservative-distributed simulation with a reduced number of control messages and without deadlock resolution. This approach is based on a part of optimism computed on the prediction time each logical process can determine for its advancement. Obviously this prediction time must be computed easily according to the structure of the simulated logical process. Timed Petri nets meet these requirements and we use their structure to evaluate the depth of the prediction. In conservative-distributed simulation, it is known that the deeper the prediction, the better the efficiency of the simulation. We present a method we have devised based on channel time prediction. We compare its performance to the Chandy–Misra method and to some related Petri nets approaches (Chiola). Experiments carried out on Sun stations show that there is more parallelism and a reduced number of null messages in the cases of deadlock avoidance. Moreover, considering deadlock detection and resolution technique we observe that in many cases no deadlock occurs with less control messages.