Polypyrrole Shell@3D‐Ni Metal Core Structured Electrodes for High‐Performance Supercapacitors

Three‐dimensional (3D) nanometal films serving as current collectors have attracted much interest recently owing to their promising application in high‐performance supercapacitors. In the process of the electrochemical reaction, the 3D structure can provide a short diffusion path for fast ion transport, and the highly conductive nanometal may serve as a backbone for facile electron transfer. In this work, a novel polypyrrole (PPy) shell@3D‐Ni‐core composite is developed to enhance the electrochemical performance of conventional PPy. With the introduction of a Ni metal core, the as‐prepared material exhibits a high specific capacitance (726 F g^?1 at a charge/discharge rate of 1 A g^?1), good rate capability (a decay of 33 % in C_sp with charge/discharge rates increasing from 1 to 20 A g^?1), and high cycle stability (only a small decrease of 4.2 % in C_sp after 1000 cycles at a scan rate of 100 mV s^?1). Furthermore, an aqueous symmetric supercapacitor device is fabricated by using the as‐prepared composite as electrodes; the device demonstrates a high energy density (≈21.2 Wh kg^?1) and superior long‐term cycle ability (only 4.4 % and 18.6 % loss in C_sp after 2000 and 5000 cycles, respectively).     

Electrochemiluminescence Enhanced by the Synergetic Effect of Porphyrin and Multi-walled Carbon Nanotubes for Uric Acid Detection

The design and exploration of efficient, stable and environmentally compatible organic emitters for an electrochemiluminescence (ECL) sensor is a promising topic. Herein, a novel environmentally-friendly luminophore, ZnBCBTP@MWCNTs, were fabricated via self-assembly of porphyrin molecules (ZnBCBTP) onto multi-walled carbon nanotubes (MWCNTs). The resulting luminophore ZnBCBTP@MWCNTs displayed not only the highly ECL property and but also the good accelerated electron mobility. Then, a label-free ECL biosensor based ZnBCBTP@MWCNTs was constructed for the ultrasensitive detection of uric acid. Excitingly, this proposed ECL biosensor performed a good linear relationship in the range of 0–300 μM with a low detection limit of 1.4 μM, thus offering another reliable and feasible sensing platform for clinical bioanalysis with good selectivity, stability, and repeatability.     

Experimental comparison of nonlinear damping performance of toroidal and conventional tuned liquid column dampers

Nonlinear Dynamics - Conventional tuned liquid column dampers (TLCDs) are deficient in multidirectionality. In contrast, toroidal TLCDs are designed to extend the application to multidirectional...     

An improved LC–MS/MS method for determination of docetaxel and its application to population pharmacokinetic study in Chinese cancer patients

Because of its unpredictable side effects and efficacy, the anticancer drug docetaxel (DTX) requires improved characterisation of its pharmacokinetic profiles through population pharmacokinetic studies. A sensitive and rugged LC–MS/MS method for the detection of DTX in human plasma was developed and optimised using paclitaxel as an internal standard (IS). The plasma samples underwent rapid extraction using hybrid solid-phase extraction-protein precipitation. The analyte and IS were separated with an isocratic system on a Zorbax Eclipse Plus C₁₈ column using water containing 0.05% acetic acid along with 20 μM of sodium acetate and methanol (30/70, v/v) as the mobile phase. Quantification was performed using a triple quadrupole mass spectrometer through multiple reaction monitoring in positive mode, using the m/z 830.3 → 548.8 and m/z 876.3 → 307.7 transitions for DTX and paclitaxel, respectively. The range of the calibration curve was 1–500 ng/mL for DTX, and the linear correlation coefficient was >0.99. The accuracies ranged from −4.6 to 4.2%, and the precision was no higher than 7.0% for the analytes. No significant matrix effect was observed. Both DTX and the IS showed considerable recovery. This method was finally applied to the establishment of a population pharmacokinetic model to optimise the clinical use of DTX.     

Optical fiber acoustic sensing multiplexing system based on TDM/SFDM

We propose a system of time-division multiplexing(TDM) and spatial frequency-division multiplexing(SFDM). Extrinsic Fabry–Perot interferometric sensors are applied to detect weak acoustic signals. The broadband source is employed, the light from it is modulated by a pulse signal sequence and is efficiently amplified by semiconductor optical amplifiers. Experimental results show that the equivalent noise pressure spectrum level is-97.2 d B re 1 rad/√Hz below 1250 Hz, and the cross talk between two sensors in one TDM channel is-32.7 d B with a cavity length difference of 60 μm. The number of sensors in this multiplexing system can theoretically reach 160.     

Fatigue life enhancement by irradiation of 12Cr1MoV steel with a Zr<Superscript>+</Superscript> ion beam. Mesoscale deformation and fracture

The structure and properties of 12Cr1MoV steel irradiated with a zirconium ion beam were studied by optical microscopy, scanning electron microscopy, and micro- and nanoindentation. It is shown that the modification covers the entire cross-section of the irradiated specimens to a depth of 1 mm. The data on irradiation-induced structural changes are used to interpret the changes in mechanical properties of the irradiated specimens under static and cyclic loading. Particular attention is given to analysis of strain estimation by the digital image correlation method.     

Microtextures Induced by Nanosecond Laser on Ni–Co Alloy Coatings

Ni–Co alloys have a wide range of applications in various fields owning to their excellent physical, chemical, and mechanical properties. In this paper, we prepare Ni–Co alloy coatings on 316L stain steel surfaces by electroplating. We present a novel approach utilizing a nanosecond laser to induce microtextures on Ni–Co alloy coatings. We study experimentally the effects of laser power and scanning rate on the surface morphologies of Ni–Co alloy coatings. The results indicate that the shape and size of induced microtextures can be controlled by the laser power and scanning rate. The size of grains increases with increase in the work current of the laser (WCL) at a certain scanning rate. With the WCL constant, the size of grains decreases with increase in scanning rate while their average height increases. It is a simple and easily-controlled method for the fabrication of microstructures on Ni–Co alloy coatings, which has promising applications in investigations of the properties of microtextured surfaces, such as friction, adhesion, and wetting.