Synthesis and thermal crosslinking of carbosiloxane and oligo(oxyethylene) polymers

Acyclic diene metathesis (ADMET) polymerization has been used in the synthesis of telechelic materials using alkoxy‐functionalized carbosiloxane or oligo(oxyethylene)‐based polymers, varying from internal to terminal cured materials or the combination of them. Previous investigations demonstrated that introduction of chain‐end crosslinking improves the stress–strain behavior of such materials. A series of saturated and unsaturated carbosiloxane and oligo(oxyethylene)‐based polymers were synthesized by ADMET polymerization using silacyclobutane as chain‐end, thermally induced crosslinker. The carbosiloxane derivatives presented pure amorphous behavior, whereas the oligo(oxyethylene) polymers were semicrystalline. The thermal curing process was monitored by differential scanning calorimetry via the exotherm between 160 and 210 °C. Mechanical properties on thermoset polymers were measured, where cured polymers showed moduli from 0.6 to 9.3 MPa, tensile strengths from 0.3 to 1.0 MPa, and elongations from 12 to 76%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Atomistic simulation of InGaN/GaN quantum disk LEDs

In this work electronic and optoelectronic properties of InGaN/GaN nanocolumn quantum disk LEDs have been studied with the multiscale simulation tool tiberCAD. Calculations have been performed with an atomistic tight-binding model. Results shows that emission energies have a minor dependence on the nanocolumn dimension while In concentration in the active region is a critical parameter.     

Mass‐Spectrometric Observation of Counter Anion Production in SU‐8 Exposed to UV Light and its Use for Dill C Parameter Determination

Photopolymerization is a phenomenon that is the basis of much of today's microfabrication technology and intense research is conducted to improve its control and the characteristics of end products for a variety of applications. The design of microscopic structures often relies on the accurate knowledge and modeling of photopolymer's behavior upon exposure, i.e. the Dill parameters, for each radiation species of interest and therefore the development of flexible characterization techniques is of great importance. SU‐8 is a popular compound that is representative of a whole class that relies on cationic polymerization, where an acid is obtained via photolysis of an onium salt during exposure. Here we report on the observation of SbF₆^? via laser desorption mass spectrometry on SU‐8 exposed to UV light at the wavelength of 365 nm and demonstrate that the yield of this counter‐anion as a function of exposure is consistent with the Dill C parameter value available in the literature. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 967–972     

Fractional order models for the homogenization and wave propagation analysis in periodic elastic beams

Meccanica - The advancement of manufacturing techniques has led to a rapid increase in the design and fabrication of periodic and architectured materials for a variety of dynamics and wave...     

Surface modification of polyamide 12 angioplasty balloons by photochemical reaction with an aromatic azide

Polyamide 12 (PA12) is used in a variety of applications when low moisture absorption, good dimensional stability, and toughness are required. Polyamide 12 is one of the polymers most frequently employed to fabricate angioplasty balloon catheters; however, its high hydrophobicity and chemical inertness require the application of coatings to make its surface more hydrophilic and biocompatible. In this work, an alternative method, based on the photochemical reaction of PA12 with a hydrophilic aromatic azide, was developed. Static and dynamic contact angle measurements evidenced that the surface modification process was able to improve PA12 wettability and that the effects were retained even after 12 months from surface treatment. Polyamide 12 modification resulted in an increase of its surface free energy, as evaluated by the van Oss, Good, and Chaudhury method. X‐ray photoelectron spectroscopy confirmed the presence of the aromatic azide on PA12 surface. Finally, compliance tests showed that the modification process did not reduce the mechanical performance of balloons.     

Reducing the computational cost of NMR crystallography of organic powders at natural isotopic abundance with the help of 13C-13C dipolar couplings

Structure determination of functional organic compounds remains a formidable challenge when the sample exists as a powder. Nuclear magnetic resonance crystallography approaches based on the comparison of experimental and Density Functional Theory (DFT)-computed ¹H chemical shifts have already demonstrated great potential for structure determination of organic powders, but limitations still persist. In this study, we discuss the possibility of using ¹³C-¹³C dipolar couplings quantified on powdered theophylline at natural isotopic abundance with the help of dynamic nuclear polarization, to realize a DFT-free, rapid screening of a pool of structures predicted by ab initio random structure search. We show that although ¹³C-¹³C dipolar couplings can identify structures possessing long range structural motifs and unit cell parameters close to those of the true structure, it must be complemented with other data to recover information about the presence and the chemical nature of the supramolecular interactions.