Singlewall carbon nanotubes covered with polystyrene nanoparticles by in‐situ miniemulsion polymerization

This work is to make carbon nanotubes dispersible in both water and organic solvents without oxidation and cutting nanotube threads. Polystyrene‐singlewall carbon nanotube (PS‐SWNT) composites were prepared with three different methods: miniemulsion polymerization, conventional emulsion polymerization, and mixing SWNT with PS latex. The two factors, crosslinking and surface coverage of PS are important factors for the mechanical and electrical properties, including dispersion states of SWNT in various solvents. The PS‐SWNT composite prepared via a conventional emulsion polymerization showed SWNT bundles entirely covered with PS, whereas the PS‐SWNT composite prepared via a miniemulsion polymerization showed SWNT partially covered with crosslinked PS nanoparticles. The method of mixing SWNTs with PS latex did not show the well dispersed state of carbon nanotubes because PS was not crosslinked and was dissolved in a solvent, and nanotubes separated from PS precipitated. So the PS nanoparticle‐SWNT composite had lower electrical resistance, and higher mechanical strength than the other composites made by the latter two methods. As the amount of SWNT increases, the bare surface area of SWNT increases and the electrical conductivity increases in the composite made by the miniemulsion polymerization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 573–584, 2006     

In‐line monitoring of UV photopolymerization with a quartz crystal resonator

An in‐line monitoring device using a quartz crystal resonator for thin film polymerization was proposed, and its performance has been evaluated by implementing in the UV polymerization of 2‐hydroxyethyl methacrylate with a photoinitiator of 1‐chloroanthraquinone. Because the variation of resonant resistance of the resonator is proportional to the square root of viscosity change that is closely related to the polymerization degree, the resistance can be used as a measure of the polymerization degree. The resistance measurements were compared with the outcome of instrumental analyses of polymerization degree using an FTIR spectrometer and a gel permeation chromatograph. The experimental results showed that the resistance measurements were consistent with the experimental outcome of the instrumental analyses, and this indicates the effectiveness of the proposed device. Owing to the simplicity and availability of the resonator system, its wide utilization in the monitoring of a variety of film polymerization processes, including photoresistor application, is expected. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2428–2439, 2006     

Local chemical distribution and electronic structure of Ge1−xTx DMS single crystals (T=Cr,Mn, Fe)

The spatial concentration distribution and local electronic structure of ferromagnetic Ge_1−xT_x (T=Cr, Mn, Fe) DMS single crystals have been investigated by using scanning photoelectron microscopy (SPEM), X-ray absorption spectroscopy (XAS), and photoemission spectroscopy (PES). It is found that doped T ions in Ge_1−xT_x crystals are chemically phase-separated, suggesting that the observed ferromagnetism arises from the phase-separated T-rich phases in Ge_1−xT_x.     

Converging Marriage in Honey-Bees Optimization and Application to Stochastic Dynamic Programming

In this paper, we first refine a recently proposed metaheuristic called “Marriage in Honey-Bees Optimization” (MBO) for solving combinatorial optimization problems with some modifications to formally show that MBO converges to the global optimum value. We then adapt MBO into an algorithm called “Honey-Bees Policy Iteration” (HBPI) for solving infinite horizon-discounted cost stochastic dynamic programming problems and show that HBPI also converges to the optimal value.     

Local control of electric current driven shell etching of multiwalled carbon nanotubes

We report on a novel method for local control of shell engineering in multiwalled carbon nanotubes (MWNTs) using Joule-heating induced electric breakdown. By modulating the heat dissipation along a nanotube, we can confine its thinning and shell breakdown to occur within localized regions of peak temperatures, which are distributed over one-half of the NT length. The modulation is achieved by using suitably designed nanomachined heat sinks with different degrees of thermal coupling at different parts of a current-carrying nanotube. The location of electric breakdown occurs precisely at the regions of high temperatures predicted by the classical finite-element model of Joule heating in the MWNT. The experiments herein provide new insight into the electric breakdown mechanism and prove unambiguously that shell removal occurs due to thermal stress, underpinning the diffusive nature of MWNTs. The method demonstrated here has the potential to be a powerful tool in realizing MWNT bearings with complex architectures for use in integrated nanoelectromechanical systems (NEMS). In addition, the breakdown current and power in the nanotubes are significantly higher than those observed in nanotubes without heat removal via additional heat sinks. This indicates future avenues for enhancing the performance of MWNTs in electrical interconnect and nanoelectronic applications. PACS  73.63.Fg; 65.80.+n     

Proof of semialgebraic covering mapping cylinder conjecture with semialgebraic covering homotopy theorem

In this paper we prove the semialgebraic version of Palais' covering homotopy theorem, and use this to prove Bredon's covering mapping cylinder conjecture positively in the semialgebraic category. Bredon's conjecture was originally stated in the topological category, and a topological version of our semialgebraic proof of the conjecture answers the original topological conjecture for topological G-spaces over “simplicial” mapping cylinders.