Chain‐growth condensation polymerization of 4‐aminobenzoic acid esters bearing tri(ethylene glycol) side chain with lithium amide base

Chain‐growth condensation polymerization of p‐aminobenzoic acid esters 1 bearing a tri(ethylene glycol) monomethyl ether side chain on the nitrogen atom was investigated by using lithium 1,1,1,3,3,3‐hexamethyldisilazide (LiHMDS) as a base. The methyl ester monomer 1a afforded polymer with low molecular weight and a broad molecular weight distribution, whereas the polymerization of the phenyl ester monomer 1b at ?20 °C yielded polymer with controlled molecular weight (M_n = 2800–13,400) and low polydispersity (M_w/M_n = 1.10–1.15). Block copolymerization of 1b and 4‐(octylamino)benzoic acid methyl ester ( 2 ) was further investigated. We found that block copolymer of poly 1b and poly 2 with defined molecular weight and low polydispersity was obtained when the polymerization of 1b was initiated with equimolar LiHMDS at ?20 °C and continued at ?50 °C, followed by addition of 2 and equimolar LiHMDS at ?10 °C. Spherical aggregates were formed when a solution of poly 1b in THF was dropped on a glass plate and dried at room temperature, although the block copolymer of poly 1b and poly 2 did not afford similar aggregates under the same conditions. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1357–1363, 2010     

InGaAsP multiple quantum well edge-emitting light-emitting diode showing low coherence characteristics using selective-area metalorganic vapor phase epitaxy

Low coherence multiple-quantum well edge-emitting light-emitting diodes were obtained using selective-area metalorganic vapor-phase epitaxial growth, which utilized growth rate enhancement on an open stripe region between mask stripes. An optical absorption region, which was controlled by selective-area growth, was introduced to suppress optical feedback. At a driving current of 100 mA and an ambient temperature of 25°C, a power of 55 μW was coupled into a single-mode fiber, and a broad spectrum without spectral ripple was observed. Low coherence characteristics and very small temperature dependence were obtained in the temperature range from -40°C to 85°C. The modulation bandwidth was 210 MHz at a bias current of 100 mA.     

The effect of UV irradiation on the reduction of Au(III) ions adsorbed on manganese dioxide.

The effect of UV (ultraviolet) irradiation on the adsorption of Au(III) ions on manganese dioxide and their reduction to Au(0) (gold with 0 valence state) was investigated using XPS (X-ray photoelectron spectroscopy) and 197Au M?ssbauer spectroscopy. The UV irradiation accelerated the adsorption and the reduction. From the fact that the proportion of Au(0) estimated from Au 4f XPS spectra for surface analysis was significantly smaller than that from 197Au M?ssbauer spectra for bulk analysis, we deduced that Au(0) was interpenetrated to the inside of manganese dioxide (into deeper places than about 30 A) where XPS is impossible to detect. The content of surface hydroxyl groups on manganese dioxide also increased due to the UV irradiation. The relationship between the charge in the content of hydroxyl groups and the interpenetration of Au(0) is discussed.     

Oblique-Incidence Characteristics of a Parallel-Aligned Nematic-Liquid-Crystal Spatial Light Modulator

We have developed optically-addressed and electrically-addressed liquid crystal spatial phase-only light modulators having no pixelized structures. We obtained a large depth of phase-only modulation and high diffraction efficiency based on the electro-optical characteristics of a parallel-aligned nematic liquid crystal. These spatial light modulators (SLM) are of the reflection type, so there would be a loss of power in the readout light from the half mirror, which was set up so as to separate the incident and reflected lights. To optimize the characteristics of a reflection type spatial phase-only light modulator, we have proposed an oblique incident optical readout setup. We have examined the effect of conditions such as the polarization direction and the incidence angle of the readout light, and the orientation of liquid crystal molecules in the SLM. High diffraction efficiency close to the theoretical maximum value was obtained by adjusting the above conditions. The simulation analysis can well explain the experimental results of phase modulation.     

Universal generation of higher-order multiringed Laguerre-Gaussian beams by using a spatial light modulator

Laguerre-Gaussian (LG) beams of various higher-order radial modes are generated by using a reflective phase-only liquid crystal on silicon (LCOS) spatial light modulator (SLM). Because of the LCOS SLM's phase-modulation characteristic of a wide spatial bandwidth, a phase modulation scheme effectively generates higher-order LG beams of up to the fifth-order radial mode. We also perform correlation analyses between the observed and the theoretical two-dimensional mode profiles to universally obtain correlation coefficients of more than 0.946, which suggest mode generations of high quality.     

Similar Structural Dynamics for the Degradation of CH3NH3PbI3 in Air and in Vacuum

We investigate the degradation path of MAPbI₃ (MA=methylammonium) films over flat TiO₂ substrates at room temperature by means of X‐ray diffraction, spectroscopic ellipsometry, X‐ray photoelectron spectroscopy, and high‐resolution transmission electron microscopy. The degradation dynamics is found to be similar in air and under vacuum conditions, which leads to the conclusion that the occurrence of intrinsic thermodynamic mechanisms is not necessarily linked to humidity. The process has an early stage, which drives the starting tetragonal lattice in the direction of a cubic atomic arrangement. This early stage is followed by a phase change towards PbI₂. We describe how this degradation product is structurally coupled with the original MAPbI₃ lattice through the orientation of its constituent PbI₆ octahedra. Our results suggest a slight octahedral rearrangement after volatilization of HI+CH₃NH₂ or MAI, with a relatively low energy cost. Our experiments also clarify why reducing the interfaces and internal defects in the perovskite lattice enhances the stability of the material.     

Precise determination of bromine in PP resin pellet by instrumental neutron activation analysis using internal standardization

Instrumental neutron activation analysis with the internal standardization was applied to the precise determination of Br in polypropylene resin of candidate certified reference material. The known amount of ¹⁹⁷Au was used as an internal standard to compensate for neutron flux inhomogeneity, to improve the γ ray measurement uncertainty and the linearity of the calibration curves. The reliability of the proposed method validated using analytical results of BCR-681. The analytical result of Br in the sample was consistent with that obtained by ID-ICPMS. The relative expanded uncertainty (k = 2) was 1.5 %, and it was equivalent to that of ID-ICPMS.