Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Design of a widely tunable laser with a chirped ladder filter

We theoretically investigated a digitally tunable laser with a chirped ladder filter and a ring resonator to obtain a wide wavelength tuning range covering the whole C- or L- band. The clear relation between the tuning range and laser structure, especially the ladder filter, is described analytically. The introduction of a chirped structure into a ladder filter is effective in achieving both wide tunability and a stable lasing mode. A numerical simulation based on multimode rate equations shows that a tuning range of over 40 nm and a mode suppression ratio over 40 dB can be achieved by introducing a chirped ladder filter.     

Synthesis and properties of furo[4,3,2-de][1]benzopyran

A new heterocycle, furo[4,3,2-de][1]benzopyran ( 2 ), was synthesized. A key step in the sequence was the allylic bromination of 3,4-dihydrofuro[4,3,2-de][1]benzopyran ( 8 ) to give 3-bromo-3,4-dihydrofuro[4,3,2-de][1]-benzopyran ( 10 ) using N-bromosuccinimide under irradiation and high dilution conditions. Bromide 10 was dealt with 1,8-diazabicyclo[5.4.0]undec-7-ene to afford compound 2 . Several reactions of 2 were examined. Protonation of 2 in trifluoroacetic acid occurred at the 2-position to form a pyrylium ion 12 . Catalytic hydrogenation of 2 with palladium on charcoal proceeded smoothly to give 8 . Reduction of 2 by sodium and ethanol afforded 3-ethyl-4-hydroxybenzofuran ( 14 ). Electrophilic substitutions of 2 such as formylation, acetylation, and bromination, occurred easily at the 2-position. The above results show that compound 2 has both properties of benzofuran and 4-methylenepyran.     

Electron g-factor in a gated InAs-inserted-channel In0.53Ga0.47As/In0.52Al0.48As heterostructure

We report on electron g-factor in an InAs-inserted In_0.53Ga_0.47As/In_0.52Al_0.48As heterostructure. The gate voltage dependence of g-factor is obtained from the coincidence method. The obtained g-factor values are surprisingly smaller than the g-factor value of bulk InAs, and it is close to the bare g-factor value of In_0.53Ga_0.47As. The large change in g-factor is observed by applying the gate voltage. The obtained gate voltage dependence is not simply explained by the energy dependence of g-factor.     

Permeability,permselectivity, and penetrant‐induced plasticization in fluorinated polyimides studied by positron lifetime measurements

The ortho‐positronium (o‐Ps) lifetime τ₃ and its intensity I₃ in various fluorinated polyimides were determined by the positron annihilation technique and were studied with the spin–lattice relaxation time T₁ and the propylene permeability, solubility, diffusivity, and permselectivity for propylene/propane in them. τ₃, I₃, and the distribution of τ₃ changed when the bulky moieties in the polyimides were changed. The polyimides, having both large τ₃ and I₃ values, exhibited a short T₁ and a high permeability with a low permselectivity. The propylene permeability and diffusivity were exponentially correlated with the product of I₃ and the average free‐volume hole size estimated from τ₃. In highly plasticized states induced by the sorption of propylene, the permeability increased with the propylene pressure in excellent agreement with the change in the free‐volume hole properties probed by o‐Ps. The large and broad distribution of the free‐volume holes and increased local chain mobility for the 2,2‐bis(3,4‐decarboxyphenyl) hexafluoropropane dianhydride‐based polyimides are thought to be important physical properties for promoting penetrant‐induced plasticization. These results suggest that o‐Ps is a powerful probe of not only the free‐volume holes but also the corresponding permeation mechanism and penetrant‐induced plasticization phenomenon. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 308–318, 2003     

Dihydroboronium derivatives of (S,S)-1,2-bis(t-butylmethylphosphino)ethane as convenient chiral ligand precursors

Dihydroboronium derivatives of (S,S)-1,2-bis(t-butylmethylphosphino)ethane (t-Bu-BisP*) were prepared and used as chiral diphosphine ligand precursors in Rh-catalyzed asymmetric hydrogenation of methyl (Z)-acetamidocinnamate to afford the hydrogenation product in up to 94% enantioselectivity.