Purification and characterization of gamma-enolase from various mammals.

The gamma subunit of enolase (gamma-enolase) was purified from the brain tissues of cow, dog, goat, pig, rabbit, and rat. The purification was achieved in only three steps: ammonium sulfate-precipitation, DE 53 cellulose ion-exchange chromatography, and polyacrylamide gel electrophoresis (PAGE) in a preparative mode. The purification procedure was comparatively more simple than previously reported methods, and the yield of gamma-enolase was sufficient for subsequent structural and immunological analyses. In all mammals, the purified gamma-enolase migrated in sodium dodecyl sulfate-PAGE (SDS-PAGE) with a molecular mass of 46 kilodaltons (kDa), and the immunological cross-reactivity between those gamma-enolases was very strong. The structural homology of these gamma-enolases was examined by peptide mapping using cyanogen bromide cleavage and subsequent two-dimensional electrophoresis. The resulting peptide patterns were highly similar and in cow, dog, and goat, the patterns were almost identical. These results indicate that structural homology, that is, the species non-specificity of gamma-enolase, appears to be very high.     

High-quality hydroxyapatite coating on biocompatible materials by laser-assisted laser ablation method

A new method for high-quality hydroxyapatite (HAp) coating is developed, the laser-assisted laser ablation method. In this method, two lasers are used. One is used for ablation of a HAp target. The other, the assist laser, is used to irradiate a Ti substrate surface. The effects of the assist laser irradiation are to anneal the HAp coating and to improve its adhesive strength to the Ti substrate. The quality of the HAp coating depends on the delay time of the assist-laser irradiation. HAp coatings obtained at a delay time of 10 microseconds or more are more amorphous. It was confirmed that the amorphous part of a coating dissolves in simulated body fluid, while the crystalline part does not. The value of the Ca/P ratio in a coating obtained at a delay time of a few microseconds is close to the stoichiometric value. PACS 81.16.Mk     

Basic study of the gelation of dimethacrylate‐type crosslinking agents

An investigation was made of the gelation of dimethacrylate‐type crosslinking agents in view of an application for separation media. The study mainly centered on a crosslinking agent, glycerol dimethacrylate (GDMA), which is relatively hydrophilic because of a hydroxyl group in the middle of its structure. The gelation of GDMA was compared with that of other hydrophobic crosslinking agents such as ethylene glycol dimethacrylate and 1,6‐hexanediol dimethacrylate. The diluents used in the study were toluene, toluene with methanol, and cyclohexanol. The gelation was observed in real time with a charge coupled device camera and dynamic light scattering (DLS). Also, the separated dry gels were extensively characterized with scanning electron microscopy, BET (N₂ absorption and desorption isotherm), and Fourier transform infrared. DLS analysis showed a stronger molecular interaction of GDMA gelation in toluene, whereas this interaction was much weaker in an alcoholic solvent such as toluene with methanol or cyclohexanol. This indicated that GDMA gelation might proceed through hydrogen bonding as well as a crosslinking reaction of vinyl groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 949–958, 2006     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Preparation and properties of isobutylene–isoprene rubber–clay nanocomposites

Isobutylene isoprene rubber (IIR)‐clay nanocomposites have been prepared successfully by melt intercalation with maleic anhydride‐grafted IIR (Ma‐g‐IIR) and organophilic clay. In IIR‐clay nanocomposites, the silicate layers of the clay were exfoliated and dispersed into the monolayer. The nanocomposites exhibited greater gas barrier properties compared with those of Ma‐g‐IIR. When 15 phr clay was added, gas barrier properties were 2.5 times greater than those of Ma‐g‐IIR. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1182–1188, 2006     

Thermal properties and fracture toughness of a liquid‐crystalline epoxy resin cured with an aromatic diamine crosslinker having a mesogenic group

A mesogenic‐type curing agent was synthesized to introduce a mesogenic group not only into epoxy resin backbones but also into the crosslink units. In the mesogenic curing agent system, the domain size became larger, and the network arrangement in each domain existed to a greater extent than that in a system cured with the ordinary diamine curing system according to the evidence from polarized optical micrographs and polarized Fourier transform infrared mapping measurements. Moreover, the fracture toughness of the system was considerably improved. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2486–2494, 2006     

Investigation of the drying conditions for amidosulfuric acid.

The drying conditions for primary standards of volumetric analysis have a significant effect on the titration results due to changes in the purity, stability and homogeneity. Amidosulfuric acid, a strong acid used as a reference material for volumetric analysis in Japan, was dried in a vacuum desiccator or heated at different temperatures, and then measured by Karl-Fischer titration, thermogravimetry/mass spectroscopy (TG-MS), ion chromatography and coulometric titration. The optimum drying conditions were at 50 degrees C for 24 h with crushing.     

Selective and simultaneous determination of phosphate and silicate ions in leaching process waters for ceramics glaze raw materials of narutal origin by ion-exclusion chromatography coupled with UV-detection after postcolumn derivatization.

The selective and simultaneous ion-exclusion chromatography (IEC) with UV-detection on a weakly acidic cation-exchange resin column in the H+ -form (TSKgel Super IC-A/C) was developed and applied for the simultaneous determination of phosphate and silicate ions as the water quality parameters required for optimizing the water-leaching process for ceramics glaze raw materials of natural origin including feldspar, woods-ash, and straw-ash. Phosphate and silicate ions in these water-leaching process water samples were separated selectively from the coexisting anions such as sulfate, chloride, nitrate and carbonate ions, based on the ion-exclusion separation mechanism. They were detected selectively and simultaneously by a postcolumn derivatization with molybdenum-yellow using the UV-detector. Under the optimized separation and detection conditions (eluent, 0-1 mM sulfuric acid; reactant, 10 mM sodium molybdate-25 mM sulfuric acid; detector, UV at 370 nm; temperature, 45 degrees C), the linearity of calibration was in the range 0.1 - 10 ppm for both phosphate and silicate ions, and the detection limits at S/N = 3 were 2.58 ppb for silicate ions and 4.75 ppb for phosphate ions. The effectiveness of this method was demonstrated in practical applications to the water-leaching process for some ceramics glaze raw materials.